|
Title: AUDI A6 C5 2.4V6 AML ME7.1 3B0907552AP - how to numb rear o2 sensors Post by: bendzji on November 08, 2014, 04:59:15 PM I'm looking to try to numb the sensivity of the rear o2 sensors -I'm getting P0420 , P0430 DTC.
Propably it happens beacause i have a LPG conversion so the exhaust gases are diffrent than on petrol ( no DTC when using it ) I found on the forum and WIKI that i should change these parameters: AHKATMN (0x18672) - leave alone AHKATMX (0x18673) - set to max AHKATS (0x18674) - set to max AHKATSB (0x18675) - set to max Are these adresses the same in my ECU eeprom? Cannot find any XDF but it's a ME7.1. In my BIN all of these values are the same. Title: Re: AUDI A6 C5 2.4V6 AML ME7.1 3B0907552AP- rear o2 sensors , maps Post by: bendzji on December 02, 2014, 03:37:52 PM After comparing bin files with a M-Box i suppose that in my bin these parameters are on:
AHKATMN -0x18662 AHKATMX -0x18663 AHKATS - 0x18664 AHKATSB -0x18665 Am i correct? I'm looking for a second ECU to play with on bench - what about other part number , let's say 3B0907552 but with F , AN or other? Title: Re: AUDI A6 C5 2.4V6 AML ME7.1 3B0907552AP - how to numb rear o2 sensors Post by: bendzji on September 30, 2015, 02:20:29 AM I've changed:
CDKAT - 181A0 CWDLSAHK - 18653 and It works , they are almost in the same place as in 3B0907552AN Title: Re: AUDI A6 C5 2.4V6 AML ME7.1 3B0907552AP - how to numb rear o2 sensors Post by: kris1855 on May 20, 2018, 03:54:35 AM I've changed: CDKAT - 181A0 CWDLSAHK - 18653 and It works , they are almost in the same place as in 3B0907552AN Hello, I am at the stage of blocking diagnostic probes behind the catalyst. I opened the bin file from ecu into the hex editor and the question in what table should I change it to block the probes. Audi a6 c5 2.4 AML 3B0907552AN Maybe someone would suggest where to look for it. Title: Re: AUDI A6 C5 2.4V6 AML ME7.1 3B0907552AP - how to numb rear o2 sensors Post by: macxxx on May 20, 2018, 05:06:20 AM You have all the info here ;)
Title: Re: AUDI A6 C5 2.4V6 AML ME7.1 3B0907552AP - how to numb rear o2 sensors Post by: kris1855 on May 20, 2018, 11:24:17 AM You have all the info here ;) I understand that in the editor hex he finds the address CDKAT - 181A0 CWDLSAHK - 18653 and I change from 01 to 00 ?? Do I understand correctly? Title: Re: AUDI A6 C5 2.4V6 AML ME7.1 3B0907552AP - how to numb rear o2 sensors Post by: macxxx on May 20, 2018, 11:25:33 AM You didnt try?
Title: Re: AUDI A6 C5 2.4V6 AML ME7.1 3B0907552AP - how to numb rear o2 sensors Post by: kris1855 on May 20, 2018, 12:50:15 PM You didnt try? I'm asking, because I do not want to make any mistakes.In the picture, I marked the value 01 and I have to change it to 00. Make a check sum and upload to ecu. (https://images84.fotosik.pl/1075/e0b8ed8cefcc3583med.jpg) (https://www.fotosik.pl/zdjecie/e0b8ed8cefcc3583) |