NefMoto

please I need help with SAI and O2 off in my car. Anyone can help me?

it is audi a4 190ps BEX

please how can I found this when I have not map pack for this?

CDSLS
CLASLVE
CLASLPE

sai use eskonf  010ED1 , 2 eskonf  010ED8
AA   FF   00   30   E3   F8   30   
AA   FF   00   30   23   F8   30

CDSLS  181B7

thank you,have you full map pack or damos for this sw?

why is changed byte number 4? SAI relay is in byte 5 and 6,or?

sorry byte 6 not,only byte 5--- from F8 to FB, right?

AA   FF   00   F0   E3   FB   3C   
AA   FF   00   F0   23   FB   3C
5 and 6
fb and 3c

rear o2 remove byte 3 F0

and SAI not only CDSLS   0181b7  CWKONABG  set 0

which address has CWKONABG ?

I dont understand..when I need remove rear o2 sensor and SAI,then is ESKONF

from
Byte0    Byte1   Byte2   Byte3   Byte4   Byte5   Byte6   
AA        FF       00        30        E3       F8       30   

to
AA   FF   00   F0   E3   FB   30

right??

why you have changed byte 4 and byte 6?

I see this from s4 wiki
    Byte 0= ZUE4 ZUE3 ZUE2 ZUE1
    Byte 1= NC NC NC NC
    Byte 2= EV4 EV3 EV2 EV1
    Byte 3= LSHHK EFLA LDR TEV
    Byte 4= BKV NC AAV MIL
    Byte 5= NC NC EKP SLP
    Byte 6= ULT UAGR SLV NWS


Abbreviations:

    ZUE=COIL
    NC=NOT CONFIGURED
    EV=INJECTOR
    LSHHK=REAR O2'S
    EFLA=(Error lamp non OBD compliant?)
    LDR/E=N75
    TEV=N80 TANK VENT VALVE
    BKV=BRAKE BOOSTER PUMP
    AAV=(shut off valve, Absperrventil vorhanden)
    MIL=(Malfunction indicator lamp, OBD)
    EKP=FUEL PUMP
    SLP=J299 SAI PUMP RELAY
    ULT/LDUVS=N249 Schubumluftventil
    UAGR=(EGR valve power amplifier)
    SLV=N112 SAI RELAY
    NWS=n205 CAMSHAFT CONTROL/VVT
    EPC - EPC light
    SLP - J299 SAI pump relay
    LDP - leak detection pump
    BKP - brake booster pump

It's only the 4th byte if you start counting with 1.

Please where is CWKONABG?

181B8

I also need help for doing this, but in a RS4 K-box! Can someone please Teller me, where I can find Eskonf 1&2?
Thanks

There is only one in the RS4 binary. It's at 10B70.

Ok, thank u a lot!

Ok in adress 10B70 in K-Box is standing 00 C0 EF FC 0C. This can't be right, or?

6/8 cylinder configurations are 13 bytes long, and nothing like the 4 cylinder variants. You'll have to dig around the forum for what you need. It's all here.

succeeded disabled the sai ? no error code ?
because approx 1 or 2 week come back error code
eskonf not enough

Are you sure that CDSLS is 181B7 and not 181A4 like in other bin files from similar ECU (for instance 8E0909518AK)?

Also I think the main thing is to find CLRSHK and CLRSKA and disable these ones otherwise correction factor won't work.

100% only death .. :(
i try find 18as compared other 1,8t damos but very big different 2 file :(

ok maybe cdsls wrong adress but need other map address :(
and 18ak xdf only see one

can you tell missing map address ?

CLASLVE
CLASLPE

CLRSHK
CLRSKA

sorry but my english not very good :(

I wish I knew addresses for CLRSHk and CLRSKA but i don't have :( I also can't find this.
But I've found a lot of other maps map file is attached.

I would have posted the addresses 3 times now if I had a 518AT original file......the kp does not help me.

thanks..
and maybe post AT original file ?
because some map passed 18AS but not all
original AT file help compared AS ..

@ddillenger

you write this forum
CLASLVE
CLASLPE
leave alone because killing fuel trim
but many other post write other :confused:

sai disable only need eskonf , cdsls ?
or need other 2 map  MSLUB ,MSLBAS ?

plz check
kp file add MSLUB  map maybe correct ?

Hi Daz,

The bin file is attached. Thanks in advance!

I have not checked your .kp file.  MSLUB in AT file locates at 0x1BA16.

yes i add same address..