NefMoto

The instructions on my software don't even show the same ECU board of my computer from my 2005 Audi S4. I'm so disgusted with Ktag. Seems to be junk... There is no way to even while you're at how it shows, I have it hooked up the best I can based on the instructions that it gives, but there is a connection error issue.

Can anybody tell me if the software can even hook up to my ecu?


Here is what I have hooked up currently:
(http://[URL=http://s8.photobucket.com/user/nitrorocket/media/Mobile%20Uploads/image_9.jpg.html][IMG]http://i8.photobucket.com/albums/a50/nitrorocket/Mobile%20Uploads/image_9.jpg)[/URL][/img]

Here is the wiring instruction on my ksuite software for Ktag:
(http://i8.photobucket.com/albums/a50/nitrorocket/Mobile%20Uploads/image_10.jpg) (http://s8.photobucket.com/user/nitrorocket/media/Mobile%20Uploads/image_10.jpg.html)
(http://Here is how my ECU board looks, its different the the one shown above:[URL=http://s8.photobucket.com/user/nitrorocket/media/Mobile%20Uploads/image_11.jpg.html][IMG]http://i8.photobucket.com/albums/a50/nitrorocket/Mobile%20Uploads/image_11.jpg)[/URL][/img]

(http://i8.photobucket.com/albums/a50/nitrorocket/Mobile%20Uploads/image_9.jpg)[/URL][/img]

Here is the wiring instruction on my ksuite software for Ktag:
(http://i8.photobucket.com/albums/a50/nitrorocket/Mobile%20Uploads/image_10.jpg) (http://s8.photobucket.com/user/nitrorocket/media/Mobile%20Uploads/image_10.jpg.html)
(http://Here is how my ECU board looks, its different the the one shown above:[URL=http://s8.photobucket.com/user/nitrorocket/media/Mobile%20Uploads/image_11.jpg.html][IMG]http://i8.photobucket.com/albums/a50/nitrorocket/Mobile%20Uploads/image_11.jpg)[/URL][/im

Here is how my ECU board looks, its different the the one shown above:
(http://i8.photobucket.com/albums/a50/nitrorocket/Mobile%20Uploads/image_11.jpg) (http://s8.photobucket.com/user/nitrorocket/media/Mobile%20Uploads/image_11.jpg.html)[/img]

Somebody informed me that there are different protocols, it was telling me my car was protocol 52, but it's actually 50. Now it shows me the correct EC you, but it still will not work.

It says there is a connection issue whenever I try to read that ecu with my K tag.

I changed the protocol like you said, and the correct instructions came up. However, it still gives me a pop up that communication error please check power and connections.

(http://i8.photobucket.com/albums/a50/nitrorocket/Mobile%20Uploads/image_13.jpg) (http://s8.photobucket.com/user/nitrorocket/media/Mobile%20Uploads/image_13.jpg.html)


(http://i8.photobucket.com/albums/a50/nitrorocket/Mobile%20Uploads/image_14.jpg) (http://s8.photobucket.com/user/nitrorocket/media/Mobile%20Uploads/image_14.jpg.html)

are you sure the k-line on your cloned tool works?

Is there a way to test it? I bought it from a very reputable seller, and it's european(was pretty expensive). I have also messaged him to see if there's anyway to test the unit.

The red light goes on when I plug it in, and when I hit read, the green light lights up until the error message occurs.

you bought a "pretty expensive" pile of shit.
buy a real one.

then you can bother them with your problems instead of asking others for free help because youre cheap.

Why don't you shut your stupid ass mouth and stay off my post. Thank you...

No need to post your relevant rude things...

Sorry for talking like that, but that was rude and not helpful at all. If everyone knew everything, nobody would post.

Hi some S4 V8 ECUs only have CAN ! K-Line will not work.

Best way for ME7.1.1 Can is desoldering.

Why would you desolder when you can bootmode?

you 100% missed my point.
my point was: youre here because you bought a cheap cloned pile of crap with NO type of support.
if you had bought a genuine tool, you could contact alientech for all the support help you need.

Nitrorocket, when you say your S4 is a 2005, is it a B6 (i.e. early 2005) or a B7 (i.e. 2005.5+)

I have a B6 2005 S4 and I can communicate/flash my ECU with the Nefmoto flashing software as long as I do it on the bench.

What I found worked was:

1) put the ECU into bootmode

2) read your EEPROM to make sure you have a backup

3) Use Argdub's 90540 reading software to read the immobilizer code and back that up too

4) once you have the EEPROM and immo coding, then disable the immobilizer (here's some pics on how to do it http://nefariousmotorsports.com/forum/index.php?topic=9030.60)

5) From there, you should be able to flash on the bench without putting it in boot mode every time. I've successfully cloned my '05 560G tiptronic ECU with immobilizer coding onto an '04 560A 6 speed ECU that way, so I know for fact that it works. The only thing is that I still can't flash with the ECU in the vehicle. But it's better than not being able to at all or having to constantly put the ECU in boot mode

The infamous cluster fuse problem, like with me7logger?

That's a good clue.
On clone units 2 or 4 wires are mixed.
Check the attachment for proper pinout.

Hi can you show me a tool that can Bootmode on ME7.1.1 Can with ST10F275?

.

MPPS
Galletto
Minimon
I/O terminal

Do you need more examples? I'm not sure what the cloned tools will do, but to be honest, I/O terminal is pretty cheap considering what it's capable of. If you do this even semi professionally I'd consider buying it.

HI, has there been a proper update to this? using a registered K-tag.

same error occurs.


Thanks.

If you have a cloned Ktag and your trying to read ME7.1.1 it'll say that the ECU is recognized as ME7.5 HW I. So you have to go back and choose that ECU protocol. Leave your wires connected as you would normally with grey on boot pin and BAM!! It reads as it should.

Sent from my SM-S908U1 using Tapatalk