|
Title: Swapped ECU from Auto to Manual Audi a4 1.8T Quattro 2003 Post by: PLVSVLTRASPAIN on January 08, 2016, 09:36:00 PM Hello fellow enthusiasts,
So I installed an Auto ECU along with a matching cluster (Immo problems) on my Audi. The old ECU got wet (previous owner) along with all the relays and relay connectors. I swapped an old Auto ECU and cluster i had laying around. I also rewired everything, the relay connectors had horrible rust damage and were giving me misfires on all cylinders along with a whole bunch of codes. Anyway, i fixed all of that but now im left with these codes and lights on my cluster. My question is, can i somehow gather and extract the data from the old ECU into the new one? Sonds too good to be true to me but i figured i'd ask on here anyway. Any help will be greatly appreciated. Much obliged :-\ :'( in advance! Here's a copy of the scan: VCDS-Lite Version: Release 1.2 Friday, 08 January 2016, 13:21:42:25689 Control Module Part Number: 8E0 909 518 AF Component and/or Version: 1.8L R4/5VT G 0003 Software Coding: 0016751 Work Shop Code: WSC 63351 VCID: 749B3B8A57A3 3 Faults Found: 18034 - Powertrain Data Bus: Missing Message from TCU P1626 - 004 - No Signal/Communication 17837 - Circuit for Brake Vacuum Pump: Open Circuit P1429 - 004 - No Signal/Communication 18320 - Pressure Sensor for Brake Boost (G294): Short to Plus P1912 - 001 - Upper Limit Exceeded ------------------------------------------------------------------------------- Address 03: ABS Brakes Labels: 8E0-614-517.LBL Controller: 8E0 614 517 H Component: ABS/ESP allrad 2328 Coding: 04275 Shop #: WSC 06435 VCID: 2D2DEEEEF409 3 Faults Found: 01826 - Sensor for Steering Angle (G85); Supply Voltage Terminal 30 35-10 - - - Intermittent 18034 - Powertrain Data Bus: Missing Message from TCU P1626 - 35-00 - - 18055 - Check Coding of ECUs on Powertrain Data Bus P1647 - 35-00 - - ------------------------------------------------------------------------------- Address 08: Auto HVAC Labels: 8E0-820-043.LBL Controller: 8E0 820 043 L Component: A4 Klimaautomat 1116 Coding: 00000 Shop #: WSC 63351 VCID: 2A27E5F2C5E7 4 Faults Found: 01810 - Actuating Motor for Temperature Flap; Right (V159) 41-10 - Blocked or No Voltage - Intermittent 01274 - Air Flow Flap Positioning Motor (V71) 41-00 - Blocked or No Voltage 00735 - Potentiometer in Positioning Motor for Air recirculation Flap (G143) 30-10 - Open or Short to Plus - Intermittent 00819 - High Pressure Sensor (G65) 07-10 - Signal too Low - Intermittent ------------------------------------------------------------------------------- Address 09: Cent. Elect. Labels: 8E0-907-279-8E2.LBL Controller: 8E0 907 279 E Component: int. Lastmodul USA 0305 Coding: 00013 Shop #: WSC 63351 VCID: 341BFB8A1723 2 Faults Found: 01800 - Light Switch (E1) 27-00 - Implausible Signal 01794 - Control Module - Incorrect Chassis (VIN) Number 35-00 - - ------------------------------------------------------------------------------- Address 15: Airbags Labels: 8E0-959-655-84.LBL Controller: 8E0 959 655 C Component: Airbag 8.4EP 2000 Coding: 0010707 Shop #: WSC 63351 VCID: 3701CC860655 5 Faults Found: 00532 - Supply Voltage B+ 002 - Lower Limit Exceeded - Intermittent 01794 - Control Module - Incorrect Chassis (VIN) Number 000 - - - Intermittent 01217 - Side Airbag Igniter; Driver Side (N199) 001 - Upper Limit Exceeded - Intermittent 00474 - Control Module for Immobilizer 004 - No Signal/Communication - Intermittent 00591 - Seat Belt Switch; Driver (E24) 010 - Open or Short to Plus - Intermittent ------------------------------------------------------------------------------- Address 16: Steering wheel Labels: 8E0-953-549.LBL Controller: 8E0 953 549 L Component: Lenksáulenmodul 0308 Coding: 00041 Shop #: WSC 63351 VCID: 3C0BD3AA3F73 1 Fault Found: 01794 - Control Module - Incorrect Chassis (VIN) Number 35-00 - - ------------------------------------------------------------------------------- Address 17: Instruments Labels: 8E0-920-9xx-8E2.LBL Controller: 8E0 920 950 L Component: KOMBI+WEGFAHRS. RB4 D36 Coding: 03200 Shop #: WSC 02301 VCID: 3217FD92ED37 WAULC68E33A306130 AUZ6Z0B0393907 4 Faults Found: 01176 - Key 07-10 - Signal too Low - Intermittent 01315 - Transmission Control Module 49-00 - No Communications 01320 - Control Module for Climatronic (J255) 49-10 - No Communications - Intermittent 01304 - Radio 49-10 - No Communications - Intermittent ------------------------------------------------------------------------------- Address 45: Inter. Monitor Labels: 8E0-951-177.LBL Controller: 8E0 951 177 Component: Innenraumueberw. 0604 Coding: 00001 Shop #: WSC 00000 VCID: EBA9A0F68A9D No fault code found. ------------------------------------------------------------------------------- Address 46: Central Conv. Labels: 8E0-959-433-MAX.LBL Controller: 8E0 959 433 BB Component: Komfortgerát T7B 1311 Coding: 11788 Shop #: WSC 63351 VCID: 72973D922DB7 15 Faults Found: 01330 - Central Control Module for Central Convenience (J393) 53-10 - Supply Voltage Too Low - Intermittent 01320 - Control Module for Climatronic (J255) 49-10 - No Communications - Intermittent 01370 - Alarm triggered by Interior Monitoring 35-00 - - 01368 - Alarm triggered by Luggage Compartment Switch 35-00 - - 01374 - Alarm triggered by Terminal 15 35-00 - - 01371 - Alarm triggered by Door Contact Switch; Driver's Side 35-00 - - 00955 - Key 1 35-00 - - 01331 - Door Control Module; Driver Side (J386) 49-10 - No Communications - Intermittent 01811 - Supply Voltage for Door Controller; Drivers Side (J386) 37-10 - Faulty - Intermittent 01332 - Door Control Module; Passenger Side (J387) 49-10 - No Communications - Intermittent 01560 - Passenger Door 59-10 - Can't Unlock - Intermittent 01812 - Supply Voltage for Door Controller; Pass. Side (J387) 37-10 - Faulty - Intermittent 01561 - Left Rear Door 59-10 - Can't Unlock - Intermittent 01334 - Door Control Module; Rear Right (J398) 49-10 - No Communications - Intermittent 01562 - Right Rear Door 59-10 - Can't Unlock - Intermittent ------------------------------------------------------------------------------- Address 55: Xenon Range Labels: 4Z7-907-357.LBL Controller: 4Z7 907 357 Component: dynamische LWR D08 Coding: 00060 Shop #: WSC 63351 VCID: 047B6B4A0703 2 Faults Found: 00776 - Level Control System Sensor; Left Front (G78) 31-00 - Open or Short to Ground 00532 - Supply Voltage B+ 07-10 - Signal too Low - Intermittent ------------------------------------------------------------------------------- Address 56: Radio Labels: 8E0-035-1xx-56.LBL Controller: 8E0 035 195 F Component: symphony II NP2 0051 Coding: 00201 Shop #: WSC 00003 VCID: 2A27E5F2C5E7 4 Faults Found: 00858 - Connection; Radio ZF Output to Antenna Amplifier 36-00 - Open Circuit 01317 - Control Module in Instrument Cluster (J285) 49-10 - No Communications - Intermittent 00466 - Control Module for Steering Column Electronics (J527) 49-10 - No Communications - Intermittent 01336 - Data Bus for Comfort System 49-10 - No Communications - Intermittent ------------------------------------------------------------------------------- Address 75: Telematics Labels: None Controller: 8E0 035 616 A Component: Telematik USA1 Coding: 0005003 Shop #: WSC 63351 VCID: 233908D6A2CD 1 Fault Found: 01531 - Emergency Battery 002 - Lower Limit Exceeded End -------------------------------------------------------------------------------------------------- Title: Re: Swapped ECU from Auto to Manual Audi a4 1.8T Quattro 2003 Post by: ddillenger on January 08, 2016, 09:43:47 PM Adapt the immobilizer, recode the ecu 0016701. Then enter the cluster, go to adaptation channel 60, and ensure that it is setup for a manual.
Title: Re: Swapped ECU from Auto to Manual Audi a4 1.8T Quattro 2003 Post by: PLVSVLTRASPAIN on January 08, 2016, 09:47:28 PM Thank you sir. I can do all this with VCDS? sorry i'm new to this, the little i know has gotten me here.
Title: Re: Swapped ECU from Auto to Manual Audi a4 1.8T Quattro 2003 Post by: PLVSVLTRASPAIN on January 08, 2016, 10:19:11 PM Adapt the immobilizer, recode the ecu 0016701. Then enter the cluster, go to adaptation channel 60, and ensure that it is setup for a manual. Update i'm in. New Value reads 1031 Pop up window says: +00001 (Engine Standard) +00002 (Auto Trans) +00004 (Brake Standard) +01024 (Inst Cluster Standard) What do i do next? Thanks Title: Re: Swapped ECU from Auto to Manual Audi a4 1.8T Quattro 2003 Post by: ddillenger on January 08, 2016, 10:44:01 PM Update i'm in. New Value reads 1031 Pop up window says: +00001 (Engine Standard) +00002 (Auto Trans) +00004 (Brake Standard) +01024 (Inst Cluster Standard) What do i do next? Thanks Subtract 2 from the total and save (1029). Then recode ecu 0016701. Then adapt immobilizer. (as I said earlier). Title: Re: Swapped ECU from Auto to Manual Audi a4 1.8T Quattro 2003 Post by: PLVSVLTRASPAIN on January 08, 2016, 10:49:41 PM You have no idea how much money you just saved me, money i don't have.
Stealership gave me an over the phone quote of $350plus. Thank you so much!! |