|
Title: Afr goes very rich Post by: elav on February 23, 2016, 11:16:55 AM hello
my car is an 1.8t audi s3 from 99, with wideband conversion 018h ecu. Around 7500 rpm the AFR goes above 11. with n75 off the Afr goes above 11 arounf 7000rpm. any ideas.... i try every thing Title: Re: Post by: adam- on February 23, 2016, 11:47:21 AM BTS?
Title: Re: Afr goes very rich Post by: aef on February 23, 2016, 11:54:47 AM So your car was a APY or APX without real egt probe. You put in BAM ecu 018h without probe because you have K04-022, not 23.
Please post a file to check how you disabled the egt probe. Please post log with egt temps. 018cb file works on 018h? Title: Re: Afr goes very rich Post by: elav on February 23, 2016, 02:09:45 PM BTS is disable
egt is fine the file works great in others car Title: Re: Afr goes very rich Post by: elav on February 23, 2016, 02:12:16 PM this is the correct log
Title: Re: Afr goes very rich Post by: armageddon on February 23, 2016, 02:51:51 PM what you have TABGBTS set to? 760ยบ?
Title: Re: Afr goes very rich Post by: phila_dot on February 23, 2016, 02:54:52 PM Is AFR desired lamsbg_w?
If so, it's a fuel cal or hardware error. Title: Re: Afr goes very rich Post by: phila_dot on February 23, 2016, 02:56:02 PM Graph load
Title: Re: Afr goes very rich Post by: elav on February 23, 2016, 08:25:10 PM load log
Title: Re: Afr goes very rich Post by: phila_dot on February 23, 2016, 08:40:46 PM Specifically rl_w, put rk_w on a seperate axis as well if you have it
Title: Re: Afr goes very rich Post by: aef on February 23, 2016, 11:17:28 PM Post a log, is this so hard to understand ::)
Title: Re: Afr goes very rich Post by: littco on February 24, 2016, 03:16:59 AM So your car was a APY or APX without real egt probe. You put in BAM ecu 018h without probe because you have K04-022, not 23. Please post a file to check how you disabled the egt probe. Please post log with egt temps. 018cb file works on 018h? if EGT wasnt disabled then it would be 0.75 all the time not just at a certain point. Title: Re: Afr goes very rich Post by: elav on February 24, 2016, 07:31:07 AM here is the log
Title: Re: Afr goes very rich Post by: aef on February 24, 2016, 07:42:30 AM if EGT wasnt disabled then it would be 0.75 all the time not just at a certain point. So its done with ESKONF, thats it? Title: Re: Afr goes very rich Post by: elav on February 24, 2016, 06:11:29 PM i just set KRMXN to 0
when lambda goes below 0,75 the ignition starts cutting Title: Re: Afr goes very rich Post by: littco on February 25, 2016, 11:21:40 AM i just set KRMXN to 0 when lambda goes below 0,75 the ignition starts cutting whats the rev limiter set to? both .. Title: Re: Afr goes very rich Post by: elav on February 26, 2016, 02:55:45 PM NmaxF 8300 all the other 8000
Title: Re: Afr goes very rich Post by: prj on February 26, 2016, 05:43:31 PM NmaxF 8300 all the other 8000 You have changed the valve springs and exhaust valves? Title: Re: Afr goes very rich Post by: elav on February 27, 2016, 07:09:08 PM yes i did ;D
|