NefMoto

Hello friends, i have a Leon 2.8 vr6 24v. Engine code BDE.
I need a damos or mappack for this motor please.
I have used the "search" but I cant find anything.
thanks!

hello.
I try to find also good deffinitions for this kind of engine, in my case AYL engine from sharan/alhambra/galaxy.

Cause need understood or find maps for calculation intake cam vvt.
Please help someone.




@pablofrtdi
I found few maps in my flash, may be helps... I did only some mods for LPG adapt

tell me what maps you need, I will happily help find them.

wanna find/use

KFNWWUE
KFNWWE
KFNWWLE
KFNWSE
WNWSMNE
WNWSMXE

or other from NW modules where is possible to setup intake camshaft settings....


thank U for your kind help ;-)

There's a BFH R32 ols file on here in the noobs area somewhere and it is the best one to line up for defining a BDE ecu as the offsets are very similar, better than many DAMOS you can get.

If you post up your stock bin I'll have a play with it as I want to build another BDE def file

This was an old one I did of some of the controls on the BDE - not sure of the revision.

thanx for pointing right way.

my stock bin is included in above posted .RAR file ;-)

 Those files you put up didn't seem to want to work with me. The ols didn't look right in some you defined but literally have only had time to spend 5-10 mins on this. Put a few maps/functions on your bin though to get you going.

The file I used was a very early def file I made on this BDE one linked below so some bits need tweaking. I think the coolant temp axis on some ES/Injection areas reads 143 across the board instead of usual temp values. Also want to check the ignition as this I usually do manually and check any slight axis offsets too - all things you should really know to look out for anyway.

So, this stock BDE is what I used so you can play with both, I have added some offsets between them so you can line the Galaxy and BDE up in Winols and cross the maps over.

http://nefariousmotorsports.com/forum/index.php?topic=7565.0title=

Thanx a lot.
It look so the files are really similar :-)
do U have fully defined your bin? to take compared part's defs?
I'm interested only for intake camshaft settings - actual ;-) 
 

sorry for repost. Here, my original BDE bin. I'm working on it with a r32 damos but some adress don't work. If anyone have a damos... I would like to remove o2s sensor, after catalyst sistem and if it's posible, lauch control and rev cut. Thanks you very much. I could pay for damos file if someone have it

please @RBPE could you help me? thanks you very much

Hi, i am in need for KFNWEGM, KFZWOP, KFZWMN and CWSAWE. I have been trying to transfer maps from BDF, but there are not enough maps. R32 maps i found differs a lot for me. I am noob and maybe i will finally learn how to do that. And one more noob question. When i tranfser maps, axis are messed up. Should i use winols option to change axis offset when transfering maps? Same problem with galaxy maps.

Pablofrtfi, if you want 2 step LC you should check PHP auto add script  somewhere here. It's really easy, i can help.

Including my bin file and BDF maps:
EDIT:
Ok, i found them

Some of the main map locations to tweak.

Thank you! :D

thank you very much!!

Please, anything can help me finding VNMX, NMAX and DNMAXH?? to do launch control. I have uploaded my project. I applied a damos from a r32. Some maps are not definitely correct.

Prokon codewords v other R32's

(https://c1.staticflickr.com/4/3857/33680914572_c564728f71_b.jpg) (https://flic.kr/p/TjgutE)prokon codewords me7.1.1. (https://flic.kr/p/TjgutE) by Rick B (https://www.flickr.com/photos/146155164@N03/), on Flickr

The damos file 29F800 should line up best with a BDE file if I remember right - attached speed locations

Oh and also if you're looking into this, there's an 032CN file knocking about, some DAMOS pack one that I've posted up some English def's for somewhere - it's actually a hybrid by the look of it, it's got power and disp/2.8 values across CAN for example, yet the torque of an R32, so some hex figures will match some won't if you're struggling with such files.

 Probably been cross flashed time and again as people do with these -  but I'd be wary of any DAMOS and build a stock file up really!

I think these kind of changes are related to the crc's and protocols of flash tools from what I can gather and what is accepted by the ecu/processors and their traps/timeouts etc

I'd try and look at these areas first if you can on any damos/def file to see what's what, would make your defining maps easier in the long run;

(https://c1.staticflickr.com/1/681/32250782496_9104758357_b.jpg) (https://flic.kr/p/R8TG35)CAN CC Hybrid R32 mk4 v BDE (https://flic.kr/p/R8TG35) by Rick B (https://www.flickr.com/photos/146155164@N03/), on Flickr

(https://c1.staticflickr.com/1/285/32250781746_c0f17afa11_b.jpg) (https://flic.kr/p/R8TFP9)CAN Displacement (https://flic.kr/p/R8TFP9) by Rick B (https://www.flickr.com/photos/146155164@N03/), on Flickr

(https://c1.staticflickr.com/1/544/32250781286_24543d70f6_b.jpg) (https://flic.kr/p/R8TFFd)CAN Torque limits mk4 5 R32 (https://flic.kr/p/R8TFFd) by Rick B (https://www.flickr.com/photos/146155164@N03/), on Flickr

(https://c1.staticflickr.com/1/450/32289614705_c064ac56ba_b.jpg) (https://flic.kr/p/RcjHuV)Cross flash R32 v BDE (https://flic.kr/p/RcjHuV) by Rick B (https://www.flickr.com/photos/146155164@N03/), on Flickr

BDE locations in screenshots should also match the BDE BG file attached in the thread (as too any other screenshots posted up).

hi,
there is someone have a way put this file into emublack?
thanks

managed to do LC??? will you share the file?