|
Title: 022 906 032 CS (ME7.1.1g - cannot enter bootmode (pic + searched for days) Post by: Platinumdub-18t on August 20, 2016, 03:40:47 PM Hello - Here is my issue... i can NOT get this ecu into boot mode like all the other ecu's i've done. This ecu is from a 2003 24v VR6 donor car, and is labelled as a benzin ME7.1.1. This ecu is similar to the Audi B6 S4 4.2 ecu's but not the same.
I have had success with reading / flashing eprom tweaks on a few 1.8t 032xx ecu's. I just swapped a freshly built 24v BDF into a 12v GLX car - ecu lets engine start and scan and all is well except immo cuts after about 1 sec... so my goal is to turn IMMO OFF on the eeprom. I already updated my bin file with new values and checksum's are done, etc. I don't need any help with that stuff... just help with bootmode on this particular ecu. closest thread on nef i have found is this: http://nefariousmotorsports.com/forum/index.php?topic=9252.0 (http://nefariousmotorsports.com/forum/index.php?topic=9252.0) I have searched like crazy and found a few interesting similar situations, but nothing has remedied my "no boot mode" yet. Here is the ECU front/back/cover (http://i700.photobucket.com/albums/ww7/platinumdub-18t/2001%20Futura%20GTI/IMG_1415_zpsnweusgix.jpg) (http://i700.photobucket.com/albums/ww7/platinumdub-18t/2001%20Futura%20GTI/IMG_1416_zpsjy8dugnp.jpg) (http://i700.photobucket.com/albums/ww7/platinumdub-18t/2001%20Futura%20GTI/IMG_1417_zpsddxkprbq.jpg) sample of the cable / ecu communicating for reads: (http://i700.photobucket.com/albums/ww7/platinumdub-18t/2001%20Futura%20GTI/IMG_1414_zpswe63lm0u.jpg) i have seen a few instances where some 7.1.1 ecu's have required resistor mods... i am not sure if this applies for this 7.1.1g or not. really hoping someone knows something specific about these 24v ECU's --- i have come across a lot of failed bootmode sob stories ... and this is one more haha. i have a typical cable everyone here is using, plus a G 1260. I even tried with my eurodyne maestro cable (for another car altogether, but getting desperate, lol) I tried to trace the circuit on the ecu board, but its covered by a large grounding zone on the backside of this one... so no dice finding anything of interest that way. i rarely ask for help with any of my projects, but i am hoping my karma is high enough to receive some this time! Title: Re: 022 906 032 CS (ME7.1.1g - cannot enter bootmode (pic + searched for days) Post by: Carsinc on August 20, 2016, 06:23:44 PM Did you really search for days?
Cause its answered here on this forum I will give you a clue they circled the problem in red in the thread where they answered. Title: Re: 022 906 032 CS (ME7.1.1g - cannot enter bootmode (pic + searched for days) Post by: jameswalker on September 08, 2016, 12:08:47 PM Interestingly I also have an ME7.1.1G but the PCB looks a little different to yours. Mine is as per my thread here where I had the same problem:
http://nefariousmotorsports.com/forum/index.php?topic=11073.0title= Title: Re: 022 906 032 CS (ME7.1.1g - cannot enter bootmode (pic + searched for days) Post by: tonytony232 on January 30, 2017, 05:16:31 PM Here u have 5p08 eeprom its similar to 95040 from ME7.5, but on ME7.1.1 ecu u can only read eeprom.
I just installed eeprom from ME7.1.1 on ME7.5 re-writed it by my custom immo off file and installed it back to ME7.1.1 P.S. If u have xprog u can do it much easier Sent from my iPhone using Tapatalk |