|
Title: Help wanted! Advice on troubleshooting ECM. Me7.1.1(Burned or Not) Post by: vwdubNam on April 02, 2018, 11:26:00 PM Hi Interballs!
Im in a situation of troubleshooting, i drive a 2004 VW Golf R32, 022 906 032 cp me7.1.1 i have both O2 sensors registering implausible signal fault on my ecu. 16518-p0134 16538-p0154 Aswell the oil temp sensor only shows on the cluster module Aswell the speedo stopped working 16885-p0501 i replaced both bosch 02 sensors before my cats, and oil level sensor and still i have the fault codes and here is my actual question? Can the ECM(Me7.1.1) have a burned input board, and how would i determine that? Any Help or links to someone As back ground info, im in africa, i cant just pop into the VW dealer and ask to fix my car, as its my project car, and they are very very expensive, and probably know less than me. Title: Re: Help wanted! Advice on troubleshooting ECM. Me7.1.1(Burned or Not) Post by: _nameless on April 03, 2018, 12:02:31 AM Hi Interballs! Well how about some loggs or a vcds printoff. The very least a list of codes. LolIm in a situation of troubleshooting, i drive a 2004 VW Golf R32, 022 906 032 cp me7.1.1 i have both O2 sensors registering implausible signal fault on my ecu. 16518-p0134 16538-p0154 Aswell the oil temp sensor only shows on the cluster module Aswell the speedo stopped working 16885-p0501 i replaced both bosch 02 sensors before my cats, and oil level sensor and still i have the fault codes and here is my actual question? Can the ECM(Me7.1.1) have a burned input board, and how would i determine that? Any Help or links to someone As back ground info, im in africa, i cant just pop into the VW dealer and ask to fix my car, as its my project car, and they are very very expensive, and probably know less than me. Title: Re: Help wanted! Advice on troubleshooting ECM. Me7.1.1(Burned or Not) Post by: vwdubNam on April 03, 2018, 03:22:47 AM Well how about some loggs or a vcds printoff. The very least a list of codes. Lol not sure of what i should do a log? Im not sure what the idle voltage should be. but measure block 30 status of B1 0111 but b2 does not change to active VAG-COM Version: Release 409.1-S Chassis Type: 1J - VW G/J/B Mk4 Scan: 01,02,03,08,16,15,17,19,22,35,46,56 ------------------------------------------------------------------------------- Address 01: Engine Controller: 022 906 032 CP Component: MOTRONIC ME7.1.1G 6463 Coding: 0000132 Shop #: WSC 76040 5 Faults Found: 16518 - Oxygen (Lambda) Sensor B1 S1: No Activity P0134 - 008 - Implausible Signal 16885 - Vehicle Speed Sensor: Implausible Signal P0501 - 004 - No Signal/Communication 16955 - Brake Switch (F): Implausible Signal P0571 - 008 - Implausible Signal 17599 - Linear O2 Sensors: Before CAT: Reversed P1191 - 008 - Implausible Signal 16538 - Oxygen (Lambda) Sensor B2 S1: No Activity P0154 - 008 - Implausible Signal Readiness: 0000 1101 ------------------------------------------------------------------------------- Title: Re: Help wanted! Advice on troubleshooting ECM. Me7.1.1(Burned or Not) Post by: nubcake on April 03, 2018, 04:49:39 AM 17599 - Linear O2 Sensors: Before CAT: Reversed P1191 - 008 - Implausible Signal Tried swapping connectors from bank1 to bank2? |