|
Title: 022906032EG r32 mk4 def needed! thank you! Post by: up50lut3 on July 30, 2018, 09:56:44 PM hey all,
i can't find a damos or xdf for my ecu.. ive tried others to compare but to no avail. I still have the rear 02's but no cats. i can either delete them or numb them to go through emissions but i cant figure out which bit is what for ither situation anyone with a little insight as to whats what would be much appreciated 0x18194 is where control bits start. i have the are where the control bits are but cant find the correct addresss for You maybe able to numb ME7's sensitivity (note: untested) using: [55][56] AHKATMN (0x18672) - leave alone AHKATMX (0x18673) - set to max AHKATS (0x18674) - set to max AHKATSB (0x18675) - set to max ....or CDHSH - Post cat O2 heater diagnosis CDHSHE - Post cat O2 heater amplifier diagnosis CDLATV - Lambda sensor aging diagnosis (tv) in OBDII-Mode (inverse: EURO-Mode) CDLASH - Lambda sensor aging diagnosis (SHK) in OBDII-Mode (inverse: EURO-Mode) CDLSH - Post cat O2 sensor diagnosis CDLSHV - Lambda sensor sensor interchange recognition (N/A for vehicles equipped with a single post cat sensor, IE 1.8t and certain vr6) CWKONLS (0x181BB) - Vehicles with 4 installed sensors - change from 51 (0x33/00110011b) to 17 (0x11/00010001b)[58] Vehicles with 2 installed sensors (default value 3), set to 1. When setting CWKONLS CDLSH must also be configured to prevent malfunction in circuit DTC's. CWKONLS.1 = 0 CWKONLS.5 = 0 Change these to disable rear O2 lambda control:[59][60] CLRHK (0x11A87) - Code word for Lambda - Bit 0 is Control post cat on/off. Set bit 2 and 0, clear bit 3 to disable; i.e. set from 72 (0x48/01001000b) to 5 (00000101b)[61] CLRHK.0 = 1 CLRHK.2 = 1 CLRHK.3 = 0 CLRHK.6 = 0 (don't care) CLRSHK - Wideband vehicles use CLRSHK. In these the default value is typically 16 (0x10/0001000b). Set bit 0 (and possibly set bit 2 and clear bit 3?) to disable (set to 5?) CLRSHK.0 = 1 CLRSHK.2 = 1(?) unconfirmed. CLRSHK.3 = 0(?) unconfirmed. CLRKA (0x11A72) - set to 0[62] * r32 eg.png (123.73 KB, 2131x911 - viewed 3 times.) * 022906032EG.bin (1024 KB - downloaded 1 times.) Title: Re: 022906032EG r32 mk4 def needed! thank you! Post by: vwdubNam on July 31, 2018, 03:15:58 AM im not sure if this would be of help
keep the post updated please. i am very much interested in it Title: Re: 022906032EG r32 mk4 def needed! thank you! Post by: tonytony232 on August 04, 2018, 01:08:52 AM hey all, i can't find a damos or xdf for my ecu.. ive tried others to compare but to no avail. I still have the rear 02's but no cats. i can either delete them or numb them to go through emissions but i cant figure out which bit is what for ither situation anyone with a little insight as to whats what would be much appreciated 0x18194 is where control bits start. i have the are where the control bits are but cant find the correct addresss for You maybe able to numb ME7's sensitivity (note: untested) using: [55][56] AHKATMN (0x18672) - leave alone AHKATMX (0x18673) - set to max AHKATS (0x18674) - set to max AHKATSB (0x18675) - set to max ....or CDHSH - Post cat O2 heater diagnosis CDHSHE - Post cat O2 heater amplifier diagnosis CDLATV - Lambda sensor aging diagnosis (tv) in OBDII-Mode (inverse: EURO-Mode) CDLASH - Lambda sensor aging diagnosis (SHK) in OBDII-Mode (inverse: EURO-Mode) CDLSH - Post cat O2 sensor diagnosis CDLSHV - Lambda sensor sensor interchange recognition (N/A for vehicles equipped with a single post cat sensor, IE 1.8t and certain vr6) CWKONLS (0x181BB) - Vehicles with 4 installed sensors - change from 51 (0x33/00110011b) to 17 (0x11/00010001b)[58] Vehicles with 2 installed sensors (default value 3), set to 1. When setting CWKONLS CDLSH must also be configured to prevent malfunction in circuit DTC's. CWKONLS.1 = 0 CWKONLS.5 = 0 Change these to disable rear O2 lambda control:[59][60] CLRHK (0x11A87) - Code word for Lambda - Bit 0 is Control post cat on/off. Set bit 2 and 0, clear bit 3 to disable; i.e. set from 72 (0x48/01001000b) to 5 (00000101b)[61] CLRHK.0 = 1 CLRHK.2 = 1 CLRHK.3 = 0 CLRHK.6 = 0 (don't care) CLRSHK - Wideband vehicles use CLRSHK. In these the default value is typically 16 (0x10/0001000b). Set bit 0 (and possibly set bit 2 and clear bit 3?) to disable (set to 5?) CLRSHK.0 = 1 CLRSHK.2 = 1(?) unconfirmed. CLRSHK.3 = 0(?) unconfirmed. CLRKA (0x11A72) - set to 0[62] * r32 eg.png (123.73 KB, 2131x911 - viewed 3 times.) * 022906032EG.bin (1024 KB - downloaded 1 times.) So, u need to delete rear o2 sensors and that’s all? |