|
Title: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: nyet on March 26, 2012, 10:06:08 AM http://nyet.org/cars/ECUxPlot/
http://nyet.org/cars/files/ECUxPlot-v1.0.0-setup.exe Nightly (BETA!) builds here: http://nyet.org/cars/ECUxPlot/nightly/ Title: Re: ECUxPlot 0.9r4.0 released Post by: nyet on March 26, 2012, 10:08:18 AM FAQ
ECUxPlot won't run Try installing as administrator ECUxPlot complains about not being able to find main class Make sure you have at LEAST Java JRE SE 6 . If that doesn't work, try Java JRE SE 7. I dont see anything! Turn off the filter (uncheck Options->Filter data). I turned off the filter. Now it's a huge mess! Turn on the filter (check Options->Filter data). With the filter on, I dont see anything! The filter option searches for a WOT run of a certain length in 3rd gear. If you don't meet that criterion, you won't see any data if you enable the filter. You can adjust the filter parameters in the "Options->Configure filter" menu. If you aren't in 3rd (or aren't logging "gear") or aren't WOT (or logging accelerator pedal position), the filter doesn't work that well. You can adjust the filter to look for a different gear in the "Options->Configure filter" menu. If you set gear to 0, the filter will ignore gear entirely. Useful if you are doing multi-gear pulls, or don't always log the same gear. If your run doesn't start low enough, or isn't long enough (RPM range too short, insufficient samples), the filter won't let any data through. If you are running into problems, please post your log file here and I will try to help. In some cases, ECUxPlot isn't detecting pedal/gear data properly from the .csv header and requires me to add your .csv format to it. What is FATS? FATS is ET from 4200-6500 in 3rd. My HP estimate is way off Adjust the numbers in "Vehicle Profiles->Edit Constants" My flow estimates (compressor map, calc AFR etc.) are way off! Adjust the numbers in "Vehicle Profiles->Edit Fueling" The "MAF" parameter is a bit confusing. If you have a non-stock intake set up, the "MAF" parameter is used to set a *correction* to the MAF values calculated by the ECU. If your tune properly calibrates MAF readings for your MAF, you should leave this parameter alone. If, however, your ECU uses underscaled MAF values (you have a larger MAF, but stock MAF maps), you will have to increase the MAF diameter. The correction that ECUxPlot is using is shown in the box right under the MAF parameter so you can check for sanity. Future release will probably only have the correction, not the diameter, since it is increasingly uncommon for people to have improperly scaled MAF numbers. If you aren't sure, you can calibrate it by hand by comparing Calc AFR with wideband data. Title: Re: ECUxPlot 0.9r4.1 released - please read the FAQ in this thread! Post by: nyet on September 04, 2012, 01:58:46 PM Migrated ECUxPlot project to github.
If you want to report bugs or request a feature, click here (https://github.com/nyetwurk/ecuxplot/issues) Title: Re: ECUxPlot 0.9r4.1 released - please read the FAQ in this thread! Post by: air_forced on September 29, 2012, 06:45:49 PM Having some issues with the filter/FATS window. Can't get data to show when filter is changed to 2nd gear. And 3rd gear data looks incorrect. Changed some settings around with no luck. I also noticed in the excel file for the log that its showing 4th and 5th gear being selected at a point in the log, when I know for a fact I skipped from 3rd to 6th. Not sure what this means.. My power levels are also way off. I edited the rpm/mph in constants, and it's even more inflated. Not sure what's going on there either. Log attached. Any help would be appreciated.
Title: Re: ECUxPlot 0.9r4.1 released - please read the FAQ in this thread! Post by: bbernd on December 07, 2012, 06:00:30 AM Under XP running fine...
Under W7 64 getting Error - "java runtime 1.5 required" - but java runtime is present on the 7 machine :P Title: Re: ECUxPlot 0.9r4.1 released - please read the FAQ in this thread! Post by: lezsi on December 08, 2012, 05:34:50 AM Under XP running fine... Under W7 64 getting Error - "java runtime 1.5 required" - but java runtime is present on the 7 machine :P Works fine for me. Win7 Ent. 64 bit SP1, JRE 1.7.0_09 Title: Re: ECUxPlot 0.9r4.1 released - please read the FAQ in this thread! Post by: bbernd on December 09, 2012, 05:53:42 AM not for me... :(
Title: Re: ECUxPlot 0.9r5.0 released - please read the FAQ in this thread! Post by: nyet on January 19, 2013, 06:01:27 PM Bump. New release. OP and topic updated.
Title: Re: ECUxPlot 0.9r5.0 released - please read the FAQ in this thread! Post by: jibberjive on January 19, 2013, 06:41:36 PM Nice, I'll have to check out the drag and drop. Any thoughts on any of the suggestions I made a while ago (I know most of them need work/effort by someone [not necessarily always you], was just curious if you given them any thought)?
Title: Re: ECUxPlot 0.9r5.0 released - please read the FAQ in this thread! Post by: nyet on January 19, 2013, 07:24:07 PM i forgot most of what we talked about except for what i put in the issues area on github...
https://github.com/nyetwurk/ecuxplot/issues please remind me (preferably by adding it there directly), its been too long :( Title: Re: ECUxPlot 0.9r4.1 released - please read the FAQ in this thread! Post by: vtraudt on January 23, 2013, 08:06:15 AM Under XP running fine... Under W7 64 getting Error - "java runtime 1.5 required" - but java runtime is present on the 7 machine :P It seems like the install went through by using 'run as administrator'. But starting the program only shows a blank graph. I used 'file open' on a few example .csv files posted here, but nothing shows. Anything missing to get ECUxPlot to work? How can I check if the required 'java' is installed (java update says I have the lastest)? I want to use Nefmoto logger. Are the CSV output by nefmoto logger 'readable' by ECUxPlot? Title: Re: ECUxPlot 0.9r5.0 released - please read the FAQ in this thread! Post by: vtraudt on January 23, 2013, 08:17:27 AM Oh: is there a basic 'operator instruction manual' for ECUxPlot?
From making sure all files are properly installed and in the right place, to how to load the correct files (what format, columns, headers, etc.) and what/how to output. Plus some 'example' files to test the installation. Note: Win7-64 Pro, Netmoto logger, MS Office Pro Plus 2010 Title: Re: ECUxPlot 0.9r5.0 released - please read the FAQ in this thread! Post by: vtraudt on January 23, 2013, 10:12:49 AM Seem like I got ECUxPlot to work on my win7-64 now, at least loading some csv file posted here shows something.
Now: I have a bunch of - Allroad 6spd - Allroad tip that I want to data log with NefMoto logger, and analyze/show the data with ECUxPlot 1. Can someone send me the correct/applicable Vehicle Profiles to use? 2. the sample CSV file I tried only puts out/exports (file/export all charts) on graph. I have seen listings that show an entire collection of charts. How can i generate those (one click)? Title: Re: ECUxPlot 0.9r5.0 released - please read the FAQ in this thread! Post by: nyet on January 23, 2013, 10:38:15 AM Oh: is there a basic 'operator instruction manual' for ECUxPlot? did you read the FAQ? ITS FREAKING RIGHT THERE AT THE TOP OF THIS PAGE geez Title: Re: ECUxPlot 0.9r5.0 released - please read the FAQ in this thread! Post by: nyet on January 23, 2013, 10:41:20 AM 1. Can someone send me the correct/applicable Vehicle Profiles to use? You'll have to supply that (vehicle weight, gearing, CD etc). its only relevant for HP estimationQuote 2. the sample CSV file I tried only puts out/exports (file/export all charts) on graph. I have seen listings that show an entire collection of charts. How can i generate those (one click)? You set up a bunch of presets then hit load all, then export all. Title: Re: ECUxPlot 0.9r5.0 released - please read the FAQ in this thread! Post by: vtraudt on January 23, 2013, 11:06:29 AM did you read the FAQ? ITS FREAKING RIGHT THERE AT THE TOP OF THIS PAGE geez Yes. Several time. Then again. Used text search function in addition to be sure: not a word a manual, how to use it, etc. But thanks for the effort. Title: Re: ECUxPlot 0.9r5.0 released - please read the FAQ in this thread! Post by: marcellus on January 31, 2013, 07:36:17 PM Is there any way to get my Zeitronix log to show up in PSI instead in millibar? The Zeitronix data is in psi, but its being converted. There is only one option for Zeitronix boost, unlike requested and actual.
Title: Re: ECUxPlot 0.9r5.0 released - please read the FAQ in this thread! Post by: nyet on January 31, 2013, 08:04:04 PM I'll take look, thanks.
https://github.com/nyetwurk/ecuxplot/issues/13 Title: Re: ECUxPlot 0.9r5.0 released - please read the FAQ in this thread! Post by: marcellus on January 31, 2013, 10:22:39 PM I tried to download the new version, thinking maybe I needed to update and now:
I have so many errors in the download process. This is the first one. Title: Re: ECUxPlot 0.9r5.0 released - please read the FAQ in this thread! Post by: nyet on January 31, 2013, 10:35:22 PM install as administrator
Title: Re: ECUxPlot 0.9r5.0 released - please read the FAQ in this thread! Post by: marcellus on January 31, 2013, 10:41:49 PM I did. Same results.
Title: Re: ECUxPlot 0.9r5.0 released - please read the FAQ in this thread! Post by: nyet on January 31, 2013, 10:46:44 PM remove the directory in program files...
Title: Re: ECUxPlot 0.9r5.1 released - please read the FAQ in this thread! Post by: marcellus on January 31, 2013, 10:53:24 PM Directory left when I uninstalled and tried to reinstall.
Title: Re: ECUxPlot 0.9r5.1 released - please read the FAQ in this thread! Post by: nyet on January 31, 2013, 10:56:50 PM how about this
Title: Re: ECUxPlot 0.9r5.1 released - please read the FAQ in this thread! Post by: marcellus on January 31, 2013, 11:01:58 PM I will try the link you just posted in a sec.
It installs as admin, but I get this when I try to open it: Title: Re: ECUxPlot 0.9r5.1 released - please read the FAQ in this thread! Post by: marcellus on January 31, 2013, 11:06:18 PM same on link posted
Title: Re: ECUxPlot 0.9r5.1 released - please read the FAQ in this thread! Post by: nyet on January 31, 2013, 11:15:52 PM can you zip up your ECUxPlot folder in program files and upload it?
Title: Re: ECUxPlot 0.9r5.1 released - please read the FAQ in this thread! Post by: nyet on January 31, 2013, 11:18:39 PM also what version of java do you have
Title: Re: ECUxPlot 0.9r5.1 released - please read the FAQ in this thread! Post by: marcellus on January 31, 2013, 11:27:09 PM java
Title: Re: ECUxPlot 0.9r5.1 released - please read the FAQ in this thread! Post by: marcellus on January 31, 2013, 11:37:34 PM Does this work?
Title: Re: ECUxPlot 0.9r5.1 released - please read the FAQ in this thread! Post by: nyet on January 31, 2013, 11:38:56 PM I think i see the problem. working on it now.
it looks like it requires java 1.7 Title: Re: ECUxPlot 0.9r5.1 released - please read the FAQ in this thread! Post by: marcellus on January 31, 2013, 11:44:36 PM I just updated Java to version Recommended Version 7 Update 11 and it works as admin now. I am still wondering about the Zeitronix though.
http://www.java.com/en/download/manual.jsp Title: Re: ECUxPlot 0.9r5.1 released - please read the FAQ in this thread! Post by: nyet on January 31, 2013, 11:56:19 PM It should be fixed in the last version...
Title: Re: ECUxPlot 0.9r5.1 released - please read the FAQ in this thread! Post by: marcellus on February 01, 2013, 08:44:43 AM Thank you NYET! It works. Also, thank you for helping me last night getting everything set back up again.
One last thing, I am having probelms with the MPH per RPM part. I dont know how to calculate it. Mine will be different I am sure since my car/trans is not S4. Its 2.8 5speed gearing, and big ole 19" wheel tire combo. What is the formula used to calculate the number I need? Title: Re: ECUxPlot 0.9r5.1 released - please read the FAQ in this thread! Post by: nyet on February 01, 2013, 09:46:02 AM GPS :)
Title: Re: ECUxPlot 0.9r5.1 released - please read the FAQ in this thread! Post by: marcellus on February 01, 2013, 10:07:40 AM Darn. Thanks anyhow.
Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: nyet on February 02, 2013, 03:02:12 AM Hopefully 0.9r5.2 fixes the java 1.6 issues.
Thanks for the feedback. Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: Bische on February 10, 2013, 08:15:02 PM Thanks a trillion times for this app! :)
Would it be much to make it read both rl and rl_w? Anytime I log rl I cant seem to plot rl_w, its getting overridden by rl which caps at 191.25 :) Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: nyet on February 10, 2013, 09:07:48 PM heh i never log rl. I'll take a look.... it could be that your .ecu file has the same alias for both?
Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: Bische on February 10, 2013, 11:46:27 PM heh i never log rl. I'll take a look.... it could be that your .ecu file has the same alias for both? That can very likely be the cause, ill take a look at that after work. Im working on a tool for calibrating KFKHFM, thats why im logging rl :) Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: Bische on February 13, 2013, 05:00:33 AM heh i never log rl. I'll take a look.... it could be that your .ecu file has the same alias for both? They had the same alias', changed the 8bit alias and now it does not show up in ECUxPlot at all lol Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: nyet on February 13, 2013, 09:10:27 AM makes no sense, there is nothing special about that column. maybe you mistyped the alias or screwed up the quotes? or try a very different alias? or send me the .csv...
Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: Bische on February 16, 2013, 01:03:42 PM makes no sense, there is nothing special about that column. maybe you mistyped the alias or screwed up the quotes? or try a very different alias? or send me the .csv... Yes, I did make a mistake when I changed the alias, now it is alles gut :) Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: NOTORIOUS VR on June 03, 2013, 07:57:20 AM Nye, I've got a suggestion for a function...
How hard is it to add a cursor line that intercepts all the graph lines and shows the value where the cursor is (much like a dynojet graph where you can choose with the mouse a spot on the graph) see the attached for eg. Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: nyet on June 03, 2013, 09:04:35 AM hmm that should be pretty easy.
Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: NOTORIOUS VR on June 13, 2013, 06:55:30 AM Can someone tell me where the Profiles are stored and how I can back them up or copy them to a different computer? I've looked just about everywhere and cannot find them.
Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: rnagy86 on June 13, 2013, 09:04:35 AM Can someone tell me where the Profiles are stored and how I can back them up or copy them to a different computer? I've looked just about everywhere and cannot find them. On windows: %APPDATA%\ECUxPlot\profiles Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: NOTORIOUS VR on June 13, 2013, 11:57:41 AM That was the 2nd place I looked (after checking the install DIR) and it doesn't exist in appdata either.
Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: nyet on June 13, 2013, 12:12:21 PM In windows, they are stored in the registry.
you'll have to export the keys :/ Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: NOTORIOUS VR on June 13, 2013, 12:13:20 PM ok that's cool... I can do that :)
Thanks Nye! Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: nyet on June 13, 2013, 12:14:13 PM HKEY_USERS\...\Software\JavaSoft\Prefs\org\nyet\ecuxplot
Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: NOTORIOUS VR on June 13, 2013, 12:16:53 PM yep, found it and exported it.. worked like a charm :)
Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: rnagy86 on June 13, 2013, 12:32:57 PM Uhm i also have them in %APPDATA%.
Code: Directory of C:\Users\robert\AppData\Roaming\ECUxPlot\profiles\foobar Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: NOTORIOUS VR on June 13, 2013, 01:55:51 PM Interesting! Maybe from a previous version or something... I don't have the DIR at all under appdata\roaming on either my desktop or laptop.
That said the two files you're showing isn't what I needed anyway :P I was talking about the profiles for graphing. Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: rnagy86 on June 13, 2013, 02:23:45 PM Interesting! Maybe from a previous version or something... I don't have the DIR at all under appdata\roaming on either my desktop or laptop. That might explain the different storage then :PThat said the two files you're showing isn't what I needed anyway :P I was talking about the profiles for graphing. Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: nyet on June 13, 2013, 03:56:32 PM Uhm i also have them in %APPDATA%. Code: Directory of C:\Users\robert\AppData\Roaming\ECUxPlot\profiles\foobar yea. very old version used to store them there. Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: masterj on August 08, 2013, 02:21:11 PM Are there any plans to show 3d logs? It could be shown as simple tables, but that would help massive
Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: nyet on August 08, 2013, 03:50:40 PM Are there any plans to show 3d logs? It could be shown as simple tables, but that would help massive i'd love to but i dont know if jfreechart supports heatmaps or 3d yet. perhaps they do, haven't checked in a while. Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: julex on August 12, 2013, 06:26:18 AM Something I was hoping you could start support...
I frequently want to throw so many things on a chart (so that I load only one preset for at-a-glance purposes) that I rung out of meaningful y-axis scaling. For example: Y-Axis 1: Load/WHP Y-Axis 2: Timing/AFR I also want to stick accel in g/s in there but due to the resulting value being at most 0.5-0.6 g, it is so compressed on Y-Axis 2 that it is pointless to even put it in there. Same would go for several other things that might not necessarily fit on any scale used in this example. If you could perhaps add an option to scale variables, even if only by decimal factor so: 0.001, 0.01, 0.1, 1 (default), 10, 100, 1000 it would be of great help as I would put said "g" value on Y-Axis 1 with a scale of 1000x and it would show nicely. Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: Bische on August 13, 2013, 09:19:29 PM Nyet, please add Calc lbs/min for us using kg/hr MAF unit instead of g/s :)
Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: julex on August 15, 2013, 06:12:48 AM And one more request, important to me...
Can you add HP/TQ/Accel etc calculations based on vehicle speed instead of RPMs? The reason I am asking is that sometimes I see wandering nmot_w during WOT pulls which completely throws off the HP/TQ/Accel calculations. I've had this issue before on a different ECU/crank sensor/clutch/FW and it is back albeit in much less severe fashion. Once you think about it, the way you do it now is actually kind of backwards as it assumes some things like that RPM signal is perfect (but it might oscillate quite heavily if the engine misfires for example and FW buffers the shocks allowing the engine to "rubber band" in respect to drive train) and rpms per mph are chosen right... Working off vfil_w would be more consistent as that's what ECU sees the tranny output shaft spinning at. Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: nyet on August 15, 2013, 08:00:15 AM Excellent point. I've actually been meaning to do this for the reasons you've mentioned.. also not sure if you noticed, but there is some pretty serious smoothing of rpm data built in as well because i've seen the same on some cars..
Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: julex on August 16, 2013, 06:23:44 AM Excellent point. I've actually been meaning to do this for the reasons you've mentioned.. also not sure if you noticed, but there is some pretty serious smoothing of rpm data built in as well because i've seen the same on some cars.. Awesome, thanks! And I appreciate adding raw RPM a while ago. Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: dream3R on September 11, 2013, 03:19:44 AM Hi Nyet,
Great bit of kit this. I was wondering if you could help me. I did look for this info but couldn't find it in print and I don't have an Audi to test the logger. I've written a CAN-BUS logger for Volvo ME7 which seems to work nice. I'd like to output the data to CSV for easy input into your software. Could you point me a list a list of field names it will automagically like (assuming there are some). Ideally I'd like to make the process as automatic as possible, it's easy enough to print whatever field names we need at the top of the CSV file. FYI, the tool will be Freeware in-case you are wondering. No plans for open source at the minute though. The variables it may log will be, rpm, gear, ait, coolant temp, egt, throttle, boost, ignition, tcv, desired boost, and both knock sensor voltages. Cheers! John. Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: nyet on September 11, 2013, 09:31:05 AM Could you point me a list a list of field names it will automagically like (assuming there are some). Sorry, I don't actually have an easily digestible list like it, but here are two possible starting points the source itself (yea, its a mess) https://github.com/nyetwurk/ecuxplot/blob/master/src/org/nyet/ecuxplot/ECUxDataset.java but more importantly: some ecu defs/aliases from ME7L (especially the 2nd column): https://github.com/nyetwurk/ME7L/blob/master/defs/me7_alias.map unfortunately, most of those names come from ECUx, so a lot of them may not make much sense, especially the Load names. Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: dream3R on September 13, 2013, 02:54:03 PM Thanks, that github linky gave me an idea.
:) Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: dream3R on October 09, 2013, 02:19:42 PM Thanks, that github linky gave me an idea. :) Pretty much got it sorted with trial and error and a browse through the source. It's a very nice bit of software you have written there!! :D Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: nyet on October 09, 2013, 08:07:46 PM Awesome. Glad somebody actually found it useful!
Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: userpike on October 10, 2013, 11:28:07 AM I read in another thread there is a .kp => XDF converter somewhere in a bundle with ECUxPlot. I looked around and I'm not finding it. I know its called mapdump. Where'd ya put it?
Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: nyet on October 10, 2013, 02:03:51 PM mapdump.exe in the ecuxplot install dir (or should be, unless i screwed up the installer again)
Title: Re: ECUxPlot 0.9r5.2 released - please read the FAQ in this thread! Post by: userpike on October 10, 2013, 09:46:57 PM mapdump.exe in the ecuxplot install dir (or should be, unless i screwed up the installer again) no, it's in there. I didn't realize it was in the folder until right now because I just checked. I was looking in ECUxPlot the program. ??? Title: Re: ECUxPlot 0.9r5.3 released - please read the FAQ in this thread! Post by: nyet on October 16, 2013, 11:32:29 PM updated to 0.9r5.3
mapdump should work now under windows. Title: Re: ECUxPlot 0.9r5.3 released - please read the FAQ in this thread! Post by: userpike on October 18, 2013, 06:50:23 PM I tried to open a 19MB log file in ECUxPlot but the file is a Log.xml, produced from Neflogger. Nothing happened but it took forever for nothing to happen. The program went unresponcive for a time and then when I tried to open anything it would just freeze up for a while after. Needless to say I didnt get it working. Is it possible to get log.xml files to load and be analyzed?
Title: Re: ECUxPlot 0.9r5.3 released - please read the FAQ in this thread! Post by: nyet on October 18, 2013, 09:32:18 PM I have not tried to get it to work with nefmoto logs yet. It DEFINITELY does not support them :(
Also, it looks like the mapdump.exe is still broken. You can try to use mapdump.jar if you are very familiar with java, but if you aren't it will probably just cause headaches. I'm actually at the track (sonoma) right now, and wont be back till tues, then leaving again the week after so its unlikely i'll have time to work on either issue until nov :/ Title: Re: ECUxPlot 0.9r5.3 released - please read the FAQ in this thread! Post by: userpike on October 18, 2013, 11:17:28 PM I have not tried to get it to work with nefmoto logs yet. It DEFINITELY does not support them :( Also, it looks like the mapdump.exe is still broken. You can try to use mapdump.jar if you are very familiar with java, but if you aren't it will probably just cause headaches. I'm actually at the track (sonoma) right now, and wont be back till tues, then leaving again the week after so its unlikely i'll have time to work on either issue until nov :/ ok I guess I'll stop trying to make it load the neflogger file. :P If I didn't PM you with the error I got from mapdump I meant to. I'll get it there eventually. Good luck at the track, thats awesome! win win win Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: nyet on October 20, 2013, 08:29:22 PM Ok, one more try... can you try 0.9r5.4?
thanks! Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: userpike on October 21, 2013, 08:21:17 AM Ok, one more try... can you try 0.9r5.4? xPlot loads the Neflogger file now but no information shows up. There are no parameters to check in the axis drop down menus either. I don't think it's reading the file correctly maybe. or you didn't add support for it yet. lolthanks! I didn't get mapdump.exe working either. I get the same error as I sent you in the PM. The .kp file I used to try it out is from 2.24 version. I remember it was said that Mapdump won't do all the different .kp versions. If you want the files I used let me know. Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: nyet on October 21, 2013, 11:27:24 PM I didn't add nef support yet, just trying to get a stable mapdump.exe
you seem to be having path problems.. can you try it making sure there is no space in the path to the file? or cd to the file directory, and run mapdump.exe like "c:\Program Files (x86)\ECUxPlot\mapdump.exe" in.kp > out.xdf if you dont use "-i" and a ref bin you will have to hand edit the xdf to add the bin file size. Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: userpike on October 22, 2013, 07:22:27 PM I didn't add nef support yet, just trying to get a stable mapdump.exe you seem to be having path problems.. can you try it making sure there is no space in the path to the file? or cd to the file directory, and run mapdump.exe like "c:\Program Files (x86)\ECUxPlot\mapdump.exe" in.kp > out.xdf if you dont use "-i" and a ref bin you will have to hand edit the xdf to add the bin file size. I've "cd"ed all the way down to ECUxPlot and ran mapdump, even copying and pasting the file path to the .kp file. Do I have to create the .xdf file first or put in the file path to where I want the file created? I tried both but get the same error but with it as the object of path error instead of the.kp. After taking spaces out of the file name and such, the errors show me more and more filename/path that is suppossedly unknown until I have taken all spaces out between words and finally I get the can not find the specified file cmd error. At first, even though the file name is "extended HS mappack- 362937.kp" the error only shows " 362937.kp" as the file name saying it is unknown. If i change the file's name to "extendedHSmappack937362.kp", in the error it shows that exactly but saying it can't be found. I even moved the file to the ECUxplot folder and get the same results. so the in.kp = C:\Program Files\ECUxplot\extendedHSmappack937362.kp If i change in the path the space between "Program" and "Files" I get the "system can not find specified file" error. I dont think this matters but I'm running this on a Vista machine. Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: nyet on October 22, 2013, 07:55:13 PM probably long filename and/or space in filename related. i dont use cmd.exe because it sucks ass for this reaason, i use bash/cygwin or linux.
in any case, it should work though; i think you have lots of quoting issues. not sure how familiar you are with cmd.exe, but its a piece of utter shit for that reason. Code: C:\Users\nyet\src\ecuxplot>dir data\8D0907551M.bin Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: userpike on October 25, 2013, 10:19:20 PM probably long filename and/or space in filename related. i dont use cmd.exe because it sucks ass for this reaason, i use bash/cygwin or linux. in any case, it should work though; i think you have lots of quoting issues. not sure how familiar you are with cmd.exe, but its a piece of utter shit for that reason. Code: C:\Users\nyet\src\ecuxplot>dir data\8D0907551M.bin Thank you for posting the screen dump and your patience. I see what you are talking about now. Syntax errors on my part. yeap, not that familiar with cmd.exe I know what "dir" does... and "cd". I was missing quotes and these guys: < >, never knew you had to use them in cmd.exe. Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: golfputtputt on October 26, 2013, 08:54:00 PM Thanks for inquiring pike! And also thanks to nyet for clarifying how to get mapdump working! You guys are awesome!
Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: golfputtputt on October 26, 2013, 09:12:04 PM Ok new issue. Attempted to use the newly converted xdf and got this error in Tunerpro RT:
Failed to load C:\Users\Meister\Desktop\userpike.kp Unrecognized encoding (parser does not support UTF-8 language encodings) whats up with this? attached is the xdf Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: nyet on October 29, 2013, 05:36:08 AM Failed to load C:\Users\Meister\Desktop\userpike.kp Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: golfputtputt on October 29, 2013, 05:36:39 PM oops I copied that error onto the forum by hand incorrectly. It said:
Failed to load C:\Users\Meister\Desktop\userpike.xdf Unrecognized encoding (parser does not support UTF-8 language encodings) My bad, my windows computer can't handle loading the internet so I'm using my mac to post to the forum and the windows to use Tunerpro RT... Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: golfputtputt on October 29, 2013, 05:38:51 PM tried it again, just to make sure I'm not retarded and did actually use the kp. Yea still got the error...
Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: nyet on October 31, 2013, 11:29:26 PM Thats not an xdf, thats a csv.
You did look at the output before trying to load it, right? Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: ddillenger on October 31, 2013, 11:50:21 PM I tried to flash this file, but the flash button was grayed out?
(http://www.metalsucks.net/wp-content/uploads/2013/03/Monkey-Mia-MJK-Australia.jpg) Why won't it work? Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: golfputtputt on November 03, 2013, 08:27:09 AM I'm lost. The file is showing it's an .xdf under file properties. Also, I followed the conversion code in your post in command. I CD'ed down to ECUxplot then inputed it the same way you did but with my username.
Quote C:\Users\nyet\src\ecuxplot>dir data\8D0907551M.bin Volume in drive C has no label. Volume Serial Number is 5CBA-D86A Directory of C:\Users\nyet\src\ecuxplot\data 09/05/2012 08:49 PM 1,048,576 8D0907551M.bin 1 File(s) 1,048,576 bytes 0 Dir(s) 16,422,436,864 bytes free C:\Users\nyet\src\ecuxplot>dir data\2.24-M.kp Volume in drive C has no label. Volume Serial Number is 5CBA-D86A Directory of C:\Users\nyet\src\ecuxplot\data 07/29/2013 10:50 PM 32,465 2.24-M.kp 1 File(s) 32,465 bytes 0 Dir(s) 16,422,436,864 bytes free C:\Users\nyet\src\ecuxplot>"c:\Program Files (x86)\ECUxPlot\mapdump.exe" -i data \8D0907551M.bin -k data\2.24-M.kp > out.csv C:\Users\nyet\src\ecuxplot>"c:\Program Files (x86)\ECUxPlot\mapdump.exe" -i data \8D0907551M.bin -k data\2.24-M.kp -x > out.xdf C:\Users\nyet\src\ecuxplot> Then, went into where ECUxplot dumped both the csv and xdf and chose the xdf and tried to load it. Unless the conversion dumped out two csv files.....not sure what's up. Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: golfputtputt on November 03, 2013, 08:29:04 AM I also, did it again, just to make sure I got the conversion correct as per the post you published about coding the conversion in command. Got the same file and same error.
Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: nyet on November 03, 2013, 02:08:43 PM I'm lost. The file is showing it's an .xdf under file properties windows "file properties" don't care about content, only the filename extension. windows sucks. Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: golfputtputt on November 03, 2013, 04:28:08 PM hmm, ok, well mapdump's conversion of the xdf from kp is spitting out a csv claiming to be an xdf. What can be done about this?
Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: nyet on November 03, 2013, 04:48:27 PM mapdump doesn't care about the filename either. It is looking for "-x".
If you omit -i and are using -x, it is likely dumping an error message into the output, which is being piped to your .xdf file. Have you looked at the contents of the .xdf? Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: golfputtputt on November 03, 2013, 04:56:36 PM I omitted -i or -x. my eyes didn't even see that was present. Let me give it another go, the right way this time. My bad.
Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: nyet on November 03, 2013, 05:04:40 PM No problem. I am working on fixing up mapdump to be bit more user friendly and removing its reliance on ">"
Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: MIL_on on November 04, 2013, 05:56:18 PM pretty cool tool nyet :)
this may be the most dumb question in this thread, but i have to ask it: is it possible to set the range of y-axis 2? if yes, where? :-[ and: does a list exist which labels are needed/used to calc the "special functions" like compressor map etc.? thank you and kind regards Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: nyet on November 04, 2013, 06:25:26 PM 1) by default, both y-axis 1 and y-axis 2 are autoscaled, but you can use the mouse to select a range you want to zoom in on.
2) no, no such coherent list exists, unfortunately, but if you are having problems I can tell you specific details for a calc func, or you can browse the source on github :/ Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: MIL_on on November 05, 2013, 12:37:48 AM ok
the reason im asking is for example the screenshot in attachment, where the lambda is a few times 4.0 which doesnt really care, but that combined with autoscale destroys completely any visibility of the data you care of that label :( alright i'll have a look in the code and maybe i can start such a map, when i find some unused time :D thank you nye! Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: nyet on November 05, 2013, 11:01:10 AM You need to use the filter so it only displays WOT
Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: MIL_on on November 05, 2013, 03:07:19 PM was already filtered!
Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: ddillenger on November 05, 2013, 03:18:23 PM That graph was not filtered.
Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: Milka on November 05, 2013, 03:51:05 PM How does the calc AFR get calculated? Which variables?
Reason I ask is because with the RS6 there are 3 mshfm variables, one for each bank and a combined. I'm assuming it's trying to use mshfm_w (combined) Also what is the MAF offset value? Stock it is 6.0 g/s but Bosch MAFs are normally 200 kg/hr ~ 55.5 g/s, but that does not work, I'm sure I'm just missing something simple. I'm using A8 MAFs (Stock A8 MLHFM, so I don't change the MAF correction) with EV14 980cc inj Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: nyet on November 05, 2013, 03:55:26 PM Also what is the MAF offset value? Thats only there in case you need to offset the MAF readings because you know your measurements are wrong (similar to if your maf is underscaled). Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: Milka on November 05, 2013, 04:09:40 PM Ok, thanks tested out mshfm and it using the combined. Thanks
Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: Milka on November 05, 2013, 05:28:03 PM Ok that is not working for the RS6? maybe an issue for 8 cyl or 980cc inj too big?
ECUxplot shows actual AFR ~14.5 during idle but AFR Calc is showing ~6? Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: nyet on November 05, 2013, 05:35:11 PM i'd probably just tweak MAF correction until it looks right at idle.
Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: Milka on November 05, 2013, 06:33:15 PM Interesting I just renamed the te columns as the ti columns and it nearly matches perfectly. Do the ti values include the injector on/off time? Hence we need to use the te values for the calculation?
Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: nyet on November 05, 2013, 06:36:56 PM Interesting I just renamed the te columns as the ti columns and it nearly matches perfectly. Do the ti values include the injector on/off time? Hence we need to use the te values for the calculation? strange. CalcAFR comes from calc MAF and whatever column is aliased to FuelInjectorOnTime Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: Milka on November 05, 2013, 06:54:11 PM I thought ti was with the latency values (tvub) and te was without so would we not want to use te (EffInjectionTime)? I could be totally wrong but looking at my log the numbers match up
Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: nyet on November 05, 2013, 06:57:07 PM Yes, good point actually. I'll have to amend the code appropriately. It really should be te, not ti.
Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: MIL_on on November 06, 2013, 01:21:08 AM Hi Nye,
is it possible, that theres a little mistake in Calc Turbo Flow in lbs/min ? Cause right now i have a car which does 165 g/s MAF which should be round about 21 lb/min. But the axis just shows 11.0 lb/min Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: nyet on November 06, 2013, 11:43:05 AM thats based on two turbos...
Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: MIL_on on November 06, 2013, 05:22:07 PM narf, damn luxury s4/rs4 guys, can even afford 2 turbos :D
i'm sorry for asking so much, i'll send you some chocolate from switzerland for christmas ;) Title: Re: ECUxPlot 0.9r5.4 released - please read the FAQ in this thread! Post by: nyet on November 12, 2013, 02:33:02 PM Yes, good point actually. I'll have to amend the code appropriately. It really should be te, not ti. 0.9r5.5 released to fix this issue. see thread starter. Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: julex on November 19, 2013, 08:36:59 AM Just wondering if you could add WHP/WTQ/HP/TQ (and any other variables that may make sense, like DRAG?) calcs based on vehicle speed instead of RPMs,
I would opt for adding extra options like "Calc WTQ (Speed Based)" and modifying old options to "Calc WTQ (RPM based)" instead of replacing them altogether. The reason for this is simple. There is currently no way to reliably compare two logs/graphs between two different cars or if you change gearing, tire size, etc. I have logs from K04 set up on my allroad, which had different transmission to what I currently have with 770s, but would also like to throw some S4 stuff on to compare too. I can't load two logs into the same graph to have apples to apples comparison as only one set of "vehicle profiles" can be used on one graph with its RPM per mile variable. If I instead open two graphs and set each to a different profiles, the auto scaling kicks in and it makes it real hard to compare and I still can't have everything overlaid nicely on one graph. It would be of great help if that could be accomplished. Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: nyet on November 19, 2013, 09:21:16 AM Yea, absolutely can be done easily. I'll try to have it in the next release.
Keep in mind that it means your tune has to take into account wheel diameter etc. so the wheel speed sensor reports the right speed... Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: julex on November 19, 2013, 09:54:27 AM Yea, absolutely can be done easily. I'll try to have it in the next release. Keep in mind that it means your tune has to take into account wheel diameter etc. so the wheel speed sensor reports the right speed... Roger, my special case is already properly adjusted for wheel size. The upgrade will neatly solve my last issue with abandoning excel altogether, Mark P's power calcs use speed which makes power measurement independent from gearing/platform. Thanks! Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: nyet on November 19, 2013, 10:12:48 AM And actually, it still suffers from the same problem if they have different weights, F/A, drag, etc :/
Profiles per LOG might be appropriate, but it could prove difficult to do, unless we add a way to provide that data inside the log itself. Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: julex on November 19, 2013, 11:02:53 AM And actually, it still suffers from the same problem if they have different weights, F/A, drag, etc :/ Profiles per LOG might be appropriate, but it could prove difficult to do, unless we add a way to provide that data inside the log itself. True, if comparing between two completely different cars but at least the same car's but different ratios would be doable... deriving from say 3rd, 4th and 5th gear runs will be fully automatic. I leave it to your to figure out something if we really want cross-platform ability to compare... Perhaps doing per log and leaving "open log" the way it is, let it apply default config. But when somebody tries "Add File", have them make a choice of which config to use? Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: MyTunes on December 09, 2013, 09:37:14 AM Thanks for fixing mapdump.exe
I just downloaded 0.9r5.5 and ran it using winblows cmd.exe and it worked perfect. used: mapdump.exe -i name.bin name.kp -x name.xdf And it generated the correct .xdf file for tuner pro from my winols .kp file that I exported. Thanks again Nye! Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: julex on January 20, 2014, 07:00:41 AM Tsk tsk, any idea when a new version will be out? Thank you!
Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: nyet on January 20, 2014, 11:09:36 AM When somebody opens a pull request that fixes all the bugs ;)
Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: dream3R on January 20, 2014, 02:04:16 PM :)
Feature request... Ability to filter by filtered run. Say three runs make it past the filter, the ability to hide one or more would be nice. Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: aef on January 21, 2014, 05:36:42 AM Is there a way to create a .kp out of .xdf using mapdump?
Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: nyet on January 21, 2014, 09:56:53 AM Is there a way to create a .kp out of .xdf using mapdump? unfortunately not. the .kp format is an utter piece of non-portable proprietary shit. in theory, we could convert .xdf to a2l and import that into OLS though. Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: julex on February 25, 2014, 08:19:18 AM When somebody opens a pull request that fixes all the bugs ;) Fix all the bugs! :). But seriously, I could really use mph/kph based calculations instead just purely RPM based. Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: SB_GLI on February 25, 2014, 08:53:20 AM I am not sure if this is already in there and I didn't notice.. but it would be nice if you could page through multiple "pulls" in a log file... Like a next pull, previous pull. Then I wouldn't have to modify log files in order for ECUxPlot to display the information that I want to see.
Sorry if this is already in there... but I didn't see it. Thanks! Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: nyet on February 25, 2014, 10:29:08 AM Fix all the bugs! :). But seriously, I could really use mph/kph based calculations instead just purely RPM based. That isn't a github "pull request" :P Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: julex on February 25, 2014, 12:34:01 PM That isn't a github "pull request" :P You added it yourself you bum ;D Add option to calculate power based on velocity data, not just RPM Nye Liu Opened by nyetwurk 6 months ago Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: nyet on February 25, 2014, 01:00:08 PM Thats not a pull request!
A pull request is a fix :) Title: Re: ECUxPlot 0.9r5.5 released - please read the FAQ in this thread! Post by: julex on March 31, 2014, 07:41:34 AM Thats not a pull request! A pull request is a fix :) Just poking :) Title: Re: ECUxPlot 0.9r5.6 released - please read the FAQ in this thread! Post by: nyet on July 18, 2014, 03:50:35 PM 0.9r5.6 released (see thread start)
* Add support for semicolon separated CSVs * Add True Timing, support mm:ss.SSS time stamps * Add aliases section for ECUx logs * Handle case where ME7Logger gets corrupted by extra whitespace * Range patch from sbloom82's pull request. Reformatted to handle whitespace problems. Title: Re: ECUxPlot 0.9r5.6 released - please read the FAQ in this thread! Post by: julex on August 26, 2014, 11:44:36 AM Hi Nyet,
I don't mean to nag but are you planning to add vehicle speed based power/TQ calculations in near future? Title: Re: ECUxPlot 0.9r5.6 released - please read the FAQ in this thread! Post by: nyet on August 26, 2014, 11:50:28 AM Crap. thanks for reminding me.
I will try to have that before the next release.. right now I'm having problems with java on MacOS... deploying java apps is a huge pain now :/ Really, what is needed is a general user-definable expression thingy ... kinda like visuallogger has ... Title: Re: ECUxPlot 0.9r5.6 released - please read the FAQ in this thread! Post by: julex on August 26, 2014, 11:59:52 AM Crap. thanks for reminding me. I will try to have that before the next release.. right now I'm having problems with java on MacOS... deploying java apps is a huge pain now :/ Really, what is needed is a general user-definable expression thingy ... kinda like visuallogger has ... ;) I support that notion! Title: Re: ECUxPlot 0.9r5.6 released - please read the FAQ in this thread! Post by: SB_GLI on August 26, 2014, 12:18:37 PM Crap. thanks for reminding me. I will try to have that before the next release.. right now I'm having problems with java on MacOS... deploying java apps is a huge pain now :/ Really, what is needed is a general user-definable expression thingy ... kinda like visuallogger has ... this was an open source project that I stole the code from. you can probably easily port this code to java. Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: nyet on October 14, 2014, 10:12:16 AM 0.9r6.0 released:
* Add option for verbose, do better at deducing units, don't add any units to axis if none found * MAF in kg/hr (issue 16) * Add note to show that rpm/mph is only used when VehicleSpeed isn't present * Support using VehicleSpeed for power/torque calcs if it exists * Add comment about how to ignore gear * Handle spaces in JAVA_HOME correctly * Look for plain "TPS" to detect throttle plate * Handle German VCDS logs * Check array bounds * Fix typo in Eff injector axis menu and calc * Add csvs so we can diff them when we do a new build * Properly detect if target rt.jar exists * Target RT back to 1.6 so we still have MacOS support * Makefile changes, Volvo logger changes * First pass at volvo logger support Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: julex on October 15, 2014, 10:10:17 AM Thanks for the speed based calculations!
Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: Lost on October 26, 2014, 05:35:44 AM Thanks for the speed based calculations! I am feeling that power n tq calculations are more off now with latest ecux. Looking through my logs and comparing too my dyno. We can say, it was more accurate before based on fats, then now. Car was dynoed on very low reading mustang, showing 413whp. Logs based on fats with older ecu x version showed 405-410whp. Now the same logs with latest ecu x shows 380whp. What's up? Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: nyet on October 26, 2014, 09:47:25 AM I am feeling that power n tq calculations are more off now with latest ecux. Looking through my logs and comparing too my dyno. We can say, it was more accurate before based on fats, then now. Car was dynoed on very low reading mustang, showing 413whp. Logs based on fats with older ecu x version showed 405-410whp. Now the same logs with latest ecu x shows 380whp. What's up? WHOA. Ugh. I was suspicious of the speed sensor, it looks like it is pretty far off ... I will make an option next release for either a speed correction factor, or an option to fall back to RPM :( I was afraid of this, but was too lazy to check it. Lesson learned: CHECK YOUR SPEEDO WITH GPS! :) Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: Lost on October 26, 2014, 12:13:35 PM WHOA. Ugh. I was suspicious of the speed sensor, it looks like it is pretty far off ... I will make an option next release for either a speed correction factor, or an option to fall back to RPM :( I was afraid of this, but was too lazy to check it. Lesson learned: CHECK YOUR SPEEDO WITH GPS! :) Options are always welcome:). Thanx N!! Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: bk56190 on November 17, 2014, 12:06:23 PM 0.9r6.0 released: * Add option for verbose, do better at deducing units, don't add any units to axis if none found * MAF in kg/hr (issue 16) * Add note to show that rpm/mph is only used when VehicleSpeed isn't present * Support using VehicleSpeed for power/torque calcs if it exists * Add comment about how to ignore gear * Handle spaces in JAVA_HOME correctly * Look for plain "TPS" to detect throttle plate * Handle German VCDS logs * Check array bounds * Fix typo in Eff injector axis menu and calc * Add csvs so we can diff them when we do a new build * Properly detect if target rt.jar exists * Target RT back to 1.6 so we still have MacOS support * Makefile changes, Volvo logger changes * First pass at volvo logger support Hi How does the power/torque calculation work ? It seems to be more accurate with older version with my car ??? Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: nyet on November 17, 2014, 12:40:09 PM Hi How does the power/torque calculation work ? It seems to be more accurate with older version with my car ??? Yea. That was a bad idea. Remove speed from your logged variables and it should fall back to RPM. Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: bk56190 on November 17, 2014, 01:41:06 PM Thx for your answer, it's ok now :)
Title: display torque - enter correct input parameters for engine/vehicle Post by: vtraudt on March 07, 2015, 07:32:17 AM What parameters (vehicle, engine) need to be entered correctly to display correct torque numbers in ECUxPlot?
Title: Re: display torque - enter correct input parameters for engine/vehicle Post by: vtraudt on March 07, 2015, 07:39:24 AM What parameters (vehicle, engine) need to be entered correctly to display correct torque numbers in ECUxPlot? Maybe someone already has put together correct profile/inputs for my cars: - B6 1.8T, 6 spd, stock MAF, 550cc - B6 1.8T, 5 spd, RS4 MAF, 550cc - C5 2.7T, 6 spd, 85mm MAF, 750cc - C5 2.7T, auto, stock MAF, stock injectors and 550cc injectors Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: aef on March 09, 2015, 04:09:12 AM Is there a way to open and display Innovate LM2 logs?
I have a csv here with Session ID, time, LM_2_O2, LM_2_RPM, Boost (in Volt) Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: nyet on March 09, 2015, 10:11:42 AM Post it (or email me) and I will add support if possible
Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: prj on March 09, 2015, 02:06:57 PM Request feature:
Text file that is parsed on startup for RPM "aliases". I use ecuxplot for great many logs - BMW, Subaru, Mitsu etc etc, and I have to go and edit most text files to change the name of the RPM to "RPM" for ecuxplot to pick it up. For example, a file like "aliases.txt": RPM;label1;label2;label3;label4 TPS;label1;label2;label3;label4 IAT;label1;label2;label3;label4 Then run the translation when the file is loaded based on the aliases file. Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: nyet on March 09, 2015, 03:15:13 PM Request feature: Text file that is parsed on startup for RPM "aliases". I use ecuxplot for great many logs - BMW, Subaru, Mitsu etc etc, and I have to go and edit most text files to change the name of the RPM to "RPM" for ecuxplot to pick it up. For example, a file like "aliases.txt": RPM;label1;label2;label3;label4 TPS;label1;label2;label3;label4 IAT;label1;label2;label3;label4 Then run the translation when the file is loaded based on the aliases file. Absolutely 100% doable... i'd really like some sort of loadable equation definition file too, for complex calcs, but I agree an "aliases" would be an excellent start. Much of it is hardcoded and really should be easily extensible. Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: phils8 on March 09, 2015, 04:38:18 PM I have created a large number of Presets. Where does ecuxplot save them? I would like to move them to a different computer.
Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: nyet on March 09, 2015, 05:01:48 PM I have created a large number of Presets. Where does ecuxplot save them? I would like to move them to a different computer. Registry.. Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: aef on March 16, 2015, 03:07:30 AM Does somebody have a vehicle profile for Audi S3 8L ?
Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: SKOLS on April 10, 2015, 04:28:53 AM Hi all....
I'm a bit ashamed to ask this question, but i'm bloked...probably forgot something, or just don't understand (I'm not speaking english very well) :-\ Since 2 hours, i try to make ECUxPLOT working on my PC (Win xp pro SP3), with the last ExP update (0.9r6.0). The install worked fine, the soft open without any issue, but i can't see anything. First, let me say i try to read a VCDS log, so, although it seems to me that this is possible, the problem may be there. Then, my car is a MED9 audi S3 8P, so perhaps i made a mistake in config setup. I try to disable filter, configure vehicule data, configure filter.....the screen remains desperately gray :(. I know that I necessarily forgotten something, but i' really don't know what. In attachement, the LOG i try to plot. Very thank's for answers. SKOLS Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: nyet on April 10, 2015, 10:07:40 AM There are problems with some VCDS logs. I have a patch but I have not uploaded a new version yet
Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: NOTORIOUS VR on April 10, 2015, 10:29:36 AM Nye, I've got a suggestion for a function... How hard is it to add a cursor line that intercepts all the graph lines and shows the value where the cursor is (much like a dynojet graph where you can choose with the mouse a spot on the graph) see the attached for eg. Hey Nye, any chance you would be able to implement this feature in your next release? :D Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: nyet on April 10, 2015, 10:36:15 AM Hey Nye, any chance you would be able to implement this feature in your next release? :D Sure. Send me a patch :P Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: NOTORIOUS VR on April 10, 2015, 11:59:55 AM Sure. Send me a patch :P like these? :P (https://diabetessource.ca/wp-content/uploads/2013/07/nicod1.jpg) Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: SKOLS on April 11, 2015, 04:04:40 AM There are problems with some VCDS logs. I have a patch but I have not uploaded a new version yet Thank's for answer, nyet.... What do you advice for MED9 data logging? Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: nyet on April 11, 2015, 10:47:29 AM Currently, you have no choice (that i know of)... VCDS or nothing.
Seeing as you are having problems I will try to get a release together this weekend.. Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: SKOLS on April 12, 2015, 09:40:56 AM Thank's nyet…
Is my log working for you? Perhaps i made something wrong… Thank's… Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: nyet on April 13, 2015, 05:04:05 PM Thank's nyet… Is my log working for you? Perhaps i made something wrong… Thank's… Your log is fine! It is ecuxplot that is broken! I have released 0.9r6.1 which should fix your issues! (I hope) Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: SKOLS on April 14, 2015, 01:20:54 AM Great nyet, it seem to work fine!!!!
Now, the job is to understand how to use it.... Thank's a lot for the time you spend for it. SKOLS Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: tweetss4estate on May 11, 2015, 08:25:40 AM My ecux plot was working all day. All of a sudden I load a log and then all it does is act like it's loading. I restart the comp and get the message "Can't open codes file Codes.DAT" and it still just thinks it's loading the log into ecux plot. I uninstall it, reinstall it same thing. Goes back to loading and doesn't do anything else.
Let me know what my next step should be. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on May 11, 2015, 09:57:04 AM I restart the comp and get the message "Can't open codes file Codes.DAT" and it still just thinks it's loading the log into ecux plot. That is a VCDS problem not an ECUxPlot problem. Consult VCDS tech support. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: tweetss4estate on May 11, 2015, 11:09:43 AM Will do. Nevertheless ECUX Plot isn't working. Just sits in loading... EDIT: Don't you get tired of being right? lol. I re loaded all of my VCDS stuff and now it works flawlessly again... I will be spending a lot more time here, I desire to learn from you all.
Title: Re: ECUxPlot 0.9r6.0 released - please read the FAQ in this thread! Post by: prj on May 14, 2015, 12:44:40 AM Request feature: Text file that is parsed on startup for RPM "aliases". I use ecuxplot for great many logs - BMW, Subaru, Mitsu etc etc, and I have to go and edit most text files to change the name of the RPM to "RPM" for ecuxplot to pick it up. For example, a file like "aliases.txt": RPM;label1;label2;label3;label4 TPS;label1;label2;label3;label4 IAT;label1;label2;label3;label4 Then run the translation when the file is loaded based on the aliases file. BUMP Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: tweetss4estate on May 14, 2015, 03:47:46 PM Has anyone honestly messed with the fueling constraints. I'm trying to get my S6 profile accurate.
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on June 21, 2015, 06:39:51 PM PRJ: any suggestions for merging a "standard" alias list with a user extended alias list? as in, if I want to change the "standard" alias list, how do merge that with what the user wants?
https://github.com/nyetwurk/ecuxplot/issues/23 Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nomad on June 30, 2015, 07:16:38 AM Installed ecuxplot couple of days ago and starteds using it yesterday, read a couple of logs and everything worked really well but now when i open my log it just sits loading and nothing happens, it will load a empty graph but the log itself will never load.. Any ideas?
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on June 30, 2015, 12:16:41 PM Installed ecuxplot couple of days ago and starteds using it yesterday, read a couple of logs and everything worked really well but now when i open my log it just sits loading and nothing happens, it will load a empty graph but the log itself will never load.. Any ideas? If it is one log that isn't working right (but the others are), please post it. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nomad on June 30, 2015, 12:46:06 PM If it is one log that isn't working right (but the others are), please post it. Ive tried with logs that worked yesterday but also with fresh made logs from today but unfortuneately none of them will load. Also tried to reinstall the program in a different location.. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nomad on June 30, 2015, 12:52:15 PM Last thing I did when it was working was to delete the Original presets that comes with the program and added my own and next time I started ecuxplot and tried to load a log it justs keep loading and nothing happens..
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nomad on June 30, 2015, 12:59:56 PM Did a "restore to default" on the preset's and now it decided to work! Seems like it didnt like that I removed the stock presets :)
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on July 01, 2015, 02:33:24 PM I think I see the problem.
https://github.com/nyetwurk/ecuxplot/issues/24 Thanks for reporting it! BTW i have starting making automated nightly builds http://nyet.org/cars/ECUxPlot/nightly/ They MAY NOT WORK OR MAY BE OTHERWISE BUGGY AND UNSTABLE! Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nomad on July 02, 2015, 07:27:48 AM I think I see the problem. https://github.com/nyetwurk/ecuxplot/issues/24 Thanks for reporting it! 8) Thanks for sharing this awesome program! Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: Lost on September 20, 2015, 08:20:30 AM I was wondering what does 1700kg for S4 stands for.
Car + driver + full tank Just Car ??? Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: prj on September 20, 2015, 12:34:13 PM PRJ: any suggestions for merging a "standard" alias list with a user extended alias list? as in, if I want to change the "standard" alias list, how do merge that with what the user wants? https://github.com/nyetwurk/ecuxplot/issues/23 Three options: a) If the .txt is present, ignore the standard list b) Add the .txt to the standard list c) Create a .txt out of the standard hardcoded list and provide a default .txt which the user can edit. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: Lost on October 17, 2015, 12:17:14 PM I was wondering what does 1700kg for S4 stands for. Car + driver + full tank Just Car ??? Hm, nobody has an answer to this one? Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: seishuku on October 17, 2015, 09:09:33 PM 1700kg is roughly 3800lbs, sounds like dry weight to me.
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on October 17, 2015, 09:44:22 PM 1700kg is roughly 3800lbs, sounds like dry weight to me. Dry weight would be pretty useless for HP estimation purposes :) Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: Lost on October 17, 2015, 11:31:00 PM Dry weight would be pretty useless for HP estimation purposes :) Ofcourse it is logical explanation. My RS weights much more with me and full tank than an S4. It bumps estimates a bit. Didn't wanna belive that. It is what it is. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: dream3R on October 30, 2015, 05:57:02 PM There's sprung and unsprung too lol
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: Lost on November 01, 2015, 01:49:02 AM Yeah, and the one before or after taking dump in the morning :)
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: Gilgamesh on November 03, 2015, 10:58:09 AM Hello nyet!
Your programm is the best for logviewing! Thanks for great work! But it would be much better if you could add manual multipliers for different Y parameters, or autoscale them in one axis. For example on this screenshot I cant see "small valued" parameters such as AFR or IAT or ignition angles against the "high valued" RPM or MAP in mBar. After 10 min in Excel I've manually prepared multiplied log on second screenshot. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on November 03, 2015, 11:40:38 AM But it would be much better if you could add manual multipliers for different Y parameters, or autoscale them in one axis. Yea this is a pretty big limitation; I just try to pick y and y2 appropriately. A generic scaling UI would be nice, but i can't figure out a way to make it both user friendly and usable (not to mention scale lable clarity) Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: Gilgamesh on November 03, 2015, 01:09:52 PM Thanks for your attention! Unfortunately I don't know how to help you with the programming matters :(
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: aef on November 04, 2015, 03:02:23 AM Is there a way to force it to remember the settings i did?
For example: it starts with the values i selected in the last log, which is great. Unfortunately it starts every time in a smaller window, not fullscreen. If i open the logs i have to change the folder view to "details" and "ordered by date" every time i open a file. Regards Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: adam- on November 04, 2015, 03:22:53 AM Is there a way to force it to remember the settings i did? Unfortunately it starts every time in a smaller window, not fullscreen. If i open the logs i have to change the folder view to "details" and "ordered by date" every time i open a file. This would be really easy to implement. If it remembers settings, they're stored somewhere. Wouldn't be too hard to get it to remember the closing screen position. That, and getting it to open the folder it was last in (must be stored), and get it to remember display settings. For most though, I think details and ordered by date would be the preference, so would be even easier to get it to do this. If it was open-source I'd add it myself. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: SB_GLI on November 04, 2015, 08:08:59 AM For most though, I think details and ordered by date would be the preference, so would be even easier to get it to do this. If it was open-source I'd add it myself. details and ordered by date would be nice. It is open source. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: adam- on November 04, 2015, 08:38:29 AM It is open source. I was gonna check this, but I can't in work. I'll have a look when I get home, wouldn't be too hard. It's Java based IIRC. Wouldn't take me too long to pick it up, I'm fluent in VB and it's basically the same. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on November 04, 2015, 11:34:06 AM https://github.com/nyetwurk/ecuxplot
Pull requests are always welcome. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: SB_GLI on November 04, 2015, 04:57:03 PM Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: adam- on November 06, 2015, 05:40:08 AM oh, so sorry. :P It's not even like it's something to be proud of tbf. :P But, it's high level, and Java isn't much different. We've all gotta start somewhere. :( Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: aef on November 06, 2015, 05:58:25 AM Does someone have the constants for a Audi S3 8L ?
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: SB_GLI on November 06, 2015, 10:25:48 AM It's not even like it's something to be proud of tbf. :P But, it's high level, and Java isn't much different. We've all gotta start somewhere. :( Ha, just kidding. I hate java just as much. And I'm a C# guy. Your code and my code compiles down to the exact same IL. :) Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: AudiSportB5S4 on December 21, 2015, 09:49:24 AM Nye,
On my netbook, I am struggling to use ECUx Plot. When I open it, it looks like it tries to launch but then nothing happens. I was doing it while watching the processes screen and can see the process come up into the queue but then drops off right away and doesn't open the app. I tried doing it with "run as admin" but still no dice. Is this a limitation you think of my netbook? I can't see ECUx plot being that hungry to the point it wouldn't open. I can run everything else fine. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on December 21, 2015, 11:53:44 AM What version of java?
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: AudiSportB5S4 on December 21, 2015, 01:19:37 PM I will check and reply later. Thought it was the latest version because I get reminders about it but let me confirm that. Would that cause it to crash if your program is requesting a certain version?
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on December 21, 2015, 01:33:16 PM ECUxPlot will not work if your java environment is broken.
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: AudiSportB5S4 on December 21, 2015, 01:41:01 PM Okay I will uninstall and re-install Java and see how that works.
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: AudiSportB5S4 on December 23, 2015, 09:03:27 AM Damn it, Nye, you know your stuff. It works after cleaning up the old Java and re-installing with new.
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on December 23, 2015, 11:54:54 AM Glad you got it working!
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: phila_dot on December 31, 2015, 07:50:53 AM Hate to be the guy to pop in with a request, but I think the ability to select which runs to display is sorely missing.
As in, say there are 5 runs in the log that meet the filter criteria, a drop down menu with checkboxes to select/deselect which ones are displayed, so that you could look at one or two at a time instead of a mad plot of lines and giant list of variables at the bottom taking up half the display. I know it's open source and maybe I will play with it some day, but it shouldn't be too difficult and it would be a massive improvement imo. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: golfputtputt on January 13, 2016, 07:51:50 PM Is there any way to filter VIA time range?
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: dream3R on January 16, 2016, 11:04:48 PM Is there any way to filter VIA time range? 0Open excel filter copy an paste back to logger format.notepad++ recommended Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: Lost on January 25, 2016, 01:40:33 PM Is it possible to get TQ graphed in NM, plz?
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: prj on March 03, 2016, 11:07:01 AM Request feature: Text file that is parsed on startup for RPM "aliases". I use ecuxplot for great many logs - BMW, Subaru, Mitsu etc etc, and I have to go and edit most text files to change the name of the RPM to "RPM" for ecuxplot to pick it up. For example, a file like "aliases.txt": RPM;label1;label2;label3;label4 TPS;label1;label2;label3;label4 IAT;label1;label2;label3;label4 Then run the translation when the file is loaded based on the aliases file. BUMP Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: SB_GLI on March 03, 2016, 04:07:53 PM Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: grifrowl on April 22, 2016, 08:31:41 PM I know I'm being dumb, I just don't know how yet.
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: vwaudiguy on April 22, 2016, 09:10:54 PM Was there a way to get a black background? :)
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: grifrowl on May 15, 2016, 12:32:54 AM Was there a way to get a black background? :) I guess I need to "brush" up on my mspaint skills. For realzies though, is there a certain .kp thats unsuported/what am i missing to be able to do this? Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: vavjettaw36 on October 05, 2016, 12:32:31 PM Which I could change the colors of the lines. Sometimes certain data gets drowned out by the intense colors. Is this functionality there and I just cannot find it?
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: vtraudt on October 05, 2016, 02:02:34 PM I sometimes change the background from the 'grey' to white so lines are more visible.
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: vwaudiguy on October 05, 2016, 02:05:16 PM I sometimes change the background from the 'grey' to white so lines are more visible. Anyone know of a way to change the background default color? As in black all the time when the application is opened? Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on October 05, 2016, 02:12:48 PM It's open source, teddy brosevelt. ;) ...Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: gin+ on December 16, 2016, 10:03:46 AM Although I cringed installing Java, I must admit, excellent tool! :)
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: jimmcgee5 on February 19, 2017, 11:06:43 AM I cant get this to run on my windows 10 laptop , reinstalled java and the program , starts fine loads the log file and then it just sits with a blue spinning circle ???, HELP :-\
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: jimmcgee5 on February 23, 2017, 04:05:57 PM sorted ;D , used regedit . searched for anything related to ECUxplot and delete , worked a charm ;D
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on February 23, 2017, 04:15:05 PM sorted ;D , used regedit . searched for anything related to ECUxplot and delete , worked a charm ;D Thanks for this update. I wish I knew which setting was causing problems, but I am glad you got it sorted. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on June 09, 2017, 11:17:29 AM Some VCDS logs do not work correctly
http://nefariousmotorsports.com/forum/index.php?topic=12649.msg104688#msg104688 Investigating now. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: adam- on September 05, 2018, 01:39:17 PM Can we select a time range for data too? So just now I have time as X, I'd like to be able to choose "from 30-50 seconds" rather than the whole log!
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: golfputtputt on October 08, 2018, 10:33:35 AM Could someone assist with mapdump? I'm having issues with it again.
Code: Microsoft Windows [Version 6.1.7601] this is with Java SE 11 installed (link on ecuxplot). Not sure what I'm doing wrong. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on October 08, 2018, 10:38:53 AM what version of .kp is it?
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: golfputtputt on October 08, 2018, 10:56:01 AM Tried this .kp and got this:
Code: Microsoft Windows [Version 6.1.7601] different kp, different bin. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on October 31, 2018, 10:39:00 AM unfortunately, mapdump only supports very very old .kps
I've tried to reverse engineer newer ones but they're a mess and I gave up :/ Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: silver2ks4 on August 15, 2019, 11:22:42 AM Is there an easy way to get the 5120 hack to display actual pressure values instead of the halved values from the logs? Multiplying the values in the log x2 maybe? I tried searching through the forums with no luck. Thanks.
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: aef on August 15, 2019, 11:35:42 AM You have to modify the vars in the Me7logger preset
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on August 15, 2019, 11:39:28 AM http://files.s4wiki.com/ME7L-ecu/
https://github.com/nyetwurk/ME7L/blob/master/ecus/5120.pl Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: silver2ks4 on August 15, 2019, 11:47:40 AM Thanks.
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: PerryRhodan on October 26, 2019, 02:29:04 AM Hi,
I have an installationproblem with Ecu X plot. Ist a javaproblem. I followed the instructions. Ecu X Plot ist installed as admin. My system is a Win7 prof 64 bit. I also installed Java like the program suggested. Ist Java runtime 13 or so on. The info card says Java version 8 update 231. If I start Ecu X Plot I get an error: "A JNI error has occured, please check your Installation and try again." After click to ok the next window is: "A Java Exception has occured". What is wrong and how can I start Ecu X :-)? I know ist a noob question, but i dont find a solution. Thank you for help. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: Blazius on October 26, 2019, 03:26:01 AM You need to install JRE. https://download.oracle.com/otn/java/jdk/8u231-b11/5b13a193868b4bf28bcb45c792fce896/jre-8u231-windows-x64.exe
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: Perry Rhodan on October 26, 2019, 07:26:50 AM Thank you I will test it.
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on October 26, 2019, 08:57:32 AM Unfortunately jre 9 is required now, and there is no standalone jre 9 installer, you will have to install the latest jdk/SE
https://github.com/nyetwurk/ecuxplot/issues/36 Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: PerryRhodan on October 26, 2019, 09:37:21 AM Oracle Needs an account and asks for a company. Is this not free for a privat user?
Or, is it possible to get an older version of Ecu X Plot which works with Java Runtime 8? Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: Blazius on October 26, 2019, 02:11:45 PM yes , my bad for link. You can download the SDK normally and it contains the required runtimes, I had to do it recently.
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: PerryRhodan on October 27, 2019, 01:52:38 AM Thank for the help. The earlier version runs with runtime 8.
Much thanks to the programmer. Ist a really helpful tool. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: curamrdan on December 24, 2019, 05:24:10 PM For others with 32bit windows and java problem, i installed obsolete but x86, 10.0.2-1 version found here, to be able run 0.9r7.0 version.
https://github.com/ojdkbuild/ojdkbuild Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: Lechuga on February 20, 2020, 12:55:12 AM Would it be possible to have TQ figures displayed in Nm?
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on February 20, 2020, 10:03:13 AM Would it be possible to have TQ figures displayed in Nm? Open a ticket, or even better, submit a PR Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: Lechuga on February 20, 2020, 02:25:17 PM I'll submit a PR this weekend
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: Lechuga on February 21, 2020, 08:41:20 AM Nyet, attached are my changes. I installed eclipse, cloned the GIT repository, made the changes to the code, but could not compile or test because of other bugs elsewhere in the code. So I am attaching the files I changed and I ask that you add them to the repository. Cheers!
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on February 21, 2020, 11:14:02 AM please open a pr
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: Lechuga on February 23, 2020, 02:05:15 AM I got a message that you accepted the PR. How long will it take to get added to the nightly builds? TIA
Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on February 23, 2020, 02:14:12 AM I got a message that you accepted the PR. How long will it take to get added to the nightly builds? TIA I closed the PR because it wasn't actually a useful PR. It was a fucking disaster. You opened a PR to merge an ancient branch (my own) into master. Not sure what you think you are doing, but you should probably learn a bit more about the github PR workflow. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: Lechuga on February 24, 2020, 01:36:47 AM Quote I closed the PR because it wasn't actually a useful PR. It was a fucking disaster. You opened a PR to merge an ancient branch (my own) into master. Not sure what you think you are doing, but you should probably learn a bit more about the github PR workflow. Woah! That's not very helpful. I only wanted to contribute. I am not a Java developer; I gave you the code changes and asked you politely to merge it and you requested I opened a PR, which I did following the only steps that github allowed me. My apologies if I am unable to jump backwards through hoops to satisfy your expectations. I will not contribute again. PD: Mind your language. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: adam- on February 24, 2020, 01:51:34 AM Woah! That's not very helpful. I'm with you on that, that reply was quite agressive for no reason. Man was only trying to help. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on February 24, 2020, 09:48:00 AM Woah! That's not very helpful. I only wanted to contribute. I am not a Java developer; I gave you the code changes and asked you politely to merge it and you requested I opened a PR, which I did following the only steps that github allowed me. My apologies if I am unable to jump backwards through hoops to satisfy your expectations. I will not contribute again. PD: Mind your language. Sorry. In any case, that isn't at all how github works. Did you review the PR before hitting submit? Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: Lechuga on February 24, 2020, 01:42:44 PM Quote Sorry. In any case, that isn't at all how github works. Did you review the PR before hitting submit? Apologies accepted. Yes. But it did not give me any other options. It was either PR from 'winols' or nothing. Then it asked me to upload the modified files in zip format (which I did) and assumed it was kosher. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on February 24, 2020, 02:35:54 PM You may want to review the github PR submission workflow.
In general 1) fork the repo to your own github projects 2) git clone your project to a local checkout dir 3) make a PR branch in the local checkout dir 4) make your changes locally 5) do a 'git diff' to make sure they make sense 6) check your changes into the PR branch 7) push the PR branch to your own githpub fork of the project 8) open a pull request to pull from your fork to main of the upstream repo All of the above requires a good working knowledge of both git and github. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: q_dubz on February 24, 2020, 10:17:22 PM You may want to review the github PR submission workflow. this is typical of engineers :P way more complicated than it needs to be but they don't care, so long as it meets the function requirement! In general 1) fork the repo to your own github projects 2) git clone your project to a local checkout dir 3) make a PR branch in the local checkout dir 4) make your changes locally 5) do a 'git diff' to make sure they make sense 6) check your changes into the PR branch 7) push the PR branch to your own githpub fork of the project 8) open a pull request to pull from your fork to main of the upstream repo All of the above requires a good working knowledge of both git and github. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: adam- on February 25, 2020, 01:21:51 AM this is typical of engineers :P way more complicated than it needs to be but they don't care, so long as it meets the function requirement! Literally this. I tried to use it ages ago and it was a ball-ache. No need for so many mouse clicks literally to request to change some code. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on February 25, 2020, 09:44:32 AM Literally this. I tried to use it ages ago and it was a ball-ache. No need for so many mouse clicks literally to request to change some code. You could also send a diff. Or a patch. But literally the entire open source universe works this way, I have opened literally dozens of PRs with projects that have 100k+ people working on it. It isn't hard. Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: aef on May 14, 2020, 08:53:12 AM Hi,
i cant figure out why one log is working, the other dont. regards Title: Re: ECUxPlot 0.9r7.0 released - please read the FAQ in this thread! Post by: nyet on July 04, 2020, 07:29:00 PM new build released, includes java runtime so no need to download java any more.
Need testers http://nyet.org/cars/files/ECUxPlot-v0.9.9-setup.exe Title: Re: ECUxPlot v0.9.9 released - please read the FAQ in this thread! Post by: Auriaka on July 05, 2020, 09:48:39 AM Ill download and try it out for ya. Will report back when I get the intake manifold back on the car tomorrow.
Family time weekend Title: Re: ECUxPlot v0.9.9 released - please read the FAQ in this thread! Post by: mcskittle on July 05, 2020, 10:04:36 AM Will let you know shortly. Thanks
Sent from my SM-N975U using Tapatalk Title: Re: ECUxPlot 0.9r6.1 released - please read the FAQ in this thread! Post by: nyet on July 05, 2020, 10:25:28 AM Hi, i cant figure out why one log is working, the other dont. regards Trying to figure this out now. Finally have a working build system again, thanks for nothing, Oracle! eta found the issue, will be fixed in the next release. Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: nyet on July 08, 2020, 02:18:10 AM new build released, includes java runtime so no need to download java any more, cobb ap support
Need testers http://nyet.org/cars/files/ECUxPlot-v1.0.0-setup.exe Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: BlackT on July 28, 2020, 04:57:31 AM new build released, includes java runtime so no need to download java any more, cobb ap support I am using it without any issuse so far, thank you very much for this updateNeed testers http://nyet.org/cars/files/ECUxPlot-v1.0.0-setup.exe Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: aef on July 31, 2020, 09:53:09 AM Hi Nyet,
finally german language vcds logs do work. i do have a new request. attached log contains rpm two times and it is not available in ecuxplot because it is renamed to rpm and rpm raw. the 2nd file attached is a test where i renamed the rpm columns and they are availible to select in ecuxplot. thank you for your great work regards Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: nyet on July 31, 2020, 03:22:09 PM That is intentional so the RPM based calculators (and most importantly, the filter) knows what to look for.
Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: Milka on July 31, 2020, 04:28:01 PM Wow, this is great work, can’t wait to get the 6 back on the road to start using it
Sent from my iPhone using Tapatalk Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: aef on August 01, 2020, 12:27:53 AM That is intentional so the RPM based calculators (and most importantly, the filter) knows what to look for. yes, understand but in my logfile you will find two different rpm values at the same time/mark one is used together with the speed and its important to select the correct one Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: nyet on August 01, 2020, 09:16:51 AM yes, understand but in my logfile you will find two different rpm values at the same time/mark one is used together with the speed and its important to select the correct one I'm not quite sure how to handle that. Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: nyet on August 01, 2020, 05:12:24 PM Working on a solution, should have a test version for you shortly
Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: nyet on August 02, 2020, 11:06:44 AM yes, understand but in my logfile you will find two different rpm values at the same time/mark one is used together with the speed and its important to select the correct one Please test, TIA! https://nyet.org/cars/ECUxPlot/nightly/ECUxPlot-v1.0.0-2-gdaef-setup.exe Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: aef on August 03, 2020, 10:10:18 AM Hi Nyet, thank you for creating that extra version
as you can see on the attachment: The mouseover on the 2nd var is not working. (red circle) I renamed the 2nd rpm to Motordrehzahl2. The Motordrehzahl1 is interpreted as your RPM, I get that. Unfortunatelly the 2nd rpm is not used for the correct drawing and thatswhy the drawing is a bit off. @20.03 its 6320rpm --> correct and its 231kmh --> incorrect because this speed is already reached at 19.90 I think the code was never meant to interpret different time(s) in one line. In me7logger files you will find one time and alot of other .values from that some time. In vcds you will have different times in one column. Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: nyet on August 03, 2020, 11:53:46 AM Hi Nyet, thank you for creating that extra version as you can see on the attachment: The mouseover on the 2nd var is not working. (red circle) I renamed the 2nd rpm to Motordrehzahl2. The Motordrehzahl1 is interpreted as your RPM, I get that. Unfortunatelly the 2nd rpm is not used for the correct drawing and thatswhy the drawing is a bit off. @20.03 its 6320rpm --> correct and its 231kmh --> incorrect because this speed is already reached at 19.90 I think the code was never meant to interpret different time(s) in one line. In me7logger files you will find one time and alot of other .values from that some time. In vcds you will have different times in one column. Yes, there is no way to fix this; there is only one real time ref per file. The most I can do is allow you to specify different times as x axis, but ECUxPlot doesn't know it's not a time axis. VCDS is really bad in this regard, its not real time series data like all other logs. Extending it to allow multiple times in the same log would be a lot of work. Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: flamy on November 19, 2020, 03:18:53 AM Hello,
I just installed the latest release at a freshly setup system with Windows 7 32bit and JRE8u271. I'm getting an error message at startup stating: "An error occurred while starting the application. The Version of %1 is not compatible with the executing version of Windows. Open the system information of the computer to check if a x86-(32Bit)- or a x64(64Bit)-version of the program is necessary and contact the supplier of the software" Is that problem known? Is there any chance to fix it? Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: nyet on November 19, 2020, 10:54:42 AM JRE9 is required for ECUxPlot
Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: flamy on November 19, 2020, 12:16:28 PM As there is no latter version as JRE8u271 for 32bit systems available it means it is only possible to use it on 64bit systems. That's too bad :(
Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: aef on November 20, 2020, 11:42:58 AM looks like the rpm range filter is not working anymore
version 1.0.0-3-g98b1 Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: nyet on November 20, 2020, 11:46:26 AM As there is no latter version as JRE8u271 for 32bit systems available it means it is only possible to use it on 64bit systems. That's too bad :( Oracle pretty much screwed everyone. Java is almost entirely useless thanks to them. I'd port it to different language but .. ugh. To make it cross platform that would likely mean electrum. Fuck that. Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: nyet on November 20, 2020, 11:47:18 AM looks like the rpm range filter is not working anymore version 1.0.0-3-g98b1 Open a ticket on github and attach the log. Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: BlackT on February 03, 2021, 10:26:00 AM Can you please make if that doesen't take you too much time... a version that can show torque in Nm?
Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: pizzaschnitzer on July 06, 2022, 10:34:09 AM https://gist.github.com/wavezhang/ba8425f24a968ec9b2a8619d7c2d86a6
latest working downloads von JDK and JRE Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: RENOxDECEPTION on November 20, 2022, 11:24:38 PM FYI
If anyone is getting visual glitches on a gaming PC in ecuxplot and are using RivaTuner Statistics Server, close it. Examples below: (https://i.imgur.com/oGlecet.png) (https://i.imgur.com/VLToTFH.png) Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: jmont23 on May 26, 2023, 04:40:51 PM Windows 10 forced my laptop to update and now my ecuxplot won't load a datalog. It allows me to start the program, select a log, but when I click open it builds the graphic area with default axis without any data displayed and freezes. I let it run for 15min just to be sure it wasn't my laptop but that didn't help. Tried all the normal stuff like power cycle, etc. Anyone else having this issue?
The update was: February 14, 2023—KB5022834 (OS Builds 19042.2604, 19044.2604, and 19045.2604) Edition Windows 10 Home Version 22H2 Installed on 11/10/2022 OS build 19045.2604 Experience Windows Feature Experience Pack 120.2212.4190.0 Title: Re: ECUxPlot v1.0.0 released - please read the FAQ in this thread! Post by: pedropp93 on July 13, 2023, 12:28:16 PM Windows 10 forced my laptop to update and now my ecuxplot won't load a datalog. It allows me to start the program, select a log, but when I click open it builds the graphic area with default axis without any data displayed and freezes. I let it run for 15min just to be sure it wasn't my laptop but that didn't help. Tried all the normal stuff like power cycle, etc. Anyone else having this issue? The update was: February 14, 2023—KB5022834 (OS Builds 19042.2604, 19044.2604, and 19045.2604) Edition Windows 10 Home Version 22H2 Installed on 11/10/2022 OS build 19045.2604 Experience Windows Feature Experience Pack 120.2212.4190.0 It seems like I have same problem (Win 11). All parameters are visible in .csv but nothing is plotted on graphs :( |