Title: A3 / s3 8L Cluster bench harness Grey Connector( FIS CONTROL) Post by: Steven97i1 on July 18, 2021, 11:00:36 AM Hey guys, i made an bench harness for the a3 8l cluster, i can connect to VCDS and so, but i need to connect the grey connector for fis.
i need to switch betwen the menus i found the pinout for the Grey connector BUT i dont know how i can wire the buttons. do i need to Connect the menu pins to - or +? please help. here is Complete pinout in English :) 1 - Terminal 15 2 - Brake pad wear 3 - Tachometer output 1 4 - not occupied 5 - Tank sensor 6 - Tank warning OBD 2 7 - Terminal 31 (sensor Ground (GND)) 8 - Coolant temperature 9 - Terminal 31 (load Ground (GND)) 10 - Oil pressure 2 (high) 11 - RPM signal 12 - A/C shut-off 13 - E-Gas/glow plug control 14 - Level control 15 - Terminal 58d 16 - Trailer turn signal 17 - High beam 18 - Left turn signal 19 - not occupied 20 - Terminal 58s 21 - Driver door contact 22 - Low coolant 23 - Terminal 30 24 - Terminal 31 (load Ground (GND)) 25 - Consumption signal 26 - Right parking light 27 - Left parking light 28 - Tachometer input 29 - Brake 30 - S-contact 31 - Tachometer output 2 32 - ESP/ASR Green Connector: 1 - Door contact (all doors) 2 - Transponder 1 3 - not occupied 4 - not occupied 5 - W-wire 6 - Tailgate 7 - Right turn signal 8 - External buzzer 9 - External gong 10 - Airbag 11 - Stand-still time output 12 - Terminal 61 13 - Parking brake/BRAKE 14 - CHECK 15 - Oil level/oil temperature 16 - not occupied 17 - Transponder 2 18 - CAN high speed (powertrain) (high +) 19 - CAN high speed (powertrain) (low -) 20 - CAN high speed (powertrain) (screen) 21 - ABS 22 - CAN low speed (comfort) (high +) 23 - CAN low speed (comfort) (low -) 24 - CAN low speed (comfort) (screen) 25 - Engine lid 26 - not occupied 27 - Belt buckle 28 - K-wire 29 - Outside temperature -input 30 - not occupied 31 - Selector range display 32 - not occupied Gray connector: 1 - Menu selection switch (menu) 2 - Menu selection switch (out A) 3 - Menu selection switch (out B) 4 - Menu selection switch (Enter) 5 - CAN high speed display (high +) 6 - CAN high speed display (low -) 7 - CAN high speed display (screen) 8 - Passenger door contact 9 - Right rear door contact 10 - Left rear door contact 11 - Enable 12 - Clock 13 - Data 14 - Brake light 15 - Windshield washer fluid level 16 - Rear lights/low beams 17 - Left board computer 18 - Right board computer 19 - Board computer, reset 20 - not occupied 21 - not occupied 22 - not occupied 23 - Button branch 1 navigation 24 - Button branch 2 navigation 25 - Button branch Telematic 26 - not occupied 27 - not occupied 28 - not occupied 29 - not occupied 30 - not occupied 31 - not occupied 32 - not occupied Title: Re: A3 / s3 8L Cluster bench harness Grey Connector( FIS CONTROL) Post by: BlackT on July 18, 2021, 11:54:29 AM Just connect to ground pin you want to go tru menu
Title: Re: A3 / s3 8L Cluster bench harness Grey Connector( FIS CONTROL) Post by: Steven97i1 on July 18, 2021, 01:47:15 PM so i need 4 buttons
1 - Menu selection switch (menu) 2 - Menu selection switch (out A) 3 - Menu selection switch (out B) 4 - Menu selection switch (Enter) and all on ground? Title: Re: A3 / s3 8L Cluster bench harness Grey Connector( FIS CONTROL) Post by: BlackT on July 18, 2021, 01:54:33 PM 17 - Left board computer ground if you need go left
18 - Right board computer etc. 19 - Board computer, reset |