Title: 01 audi s4 holset turbo Post by: Surferkirsch on August 09, 2012, 11:26:08 PM So i bought this car with a worn out clutch about 6 months ago, 158xxx, decided to go ahead and upgrade to ko4s when i changed the clutch, along with a full gasket set. A week ago, the porcelin from a spark plug fell out of the plug and locked my right side turbo, destroying the wheels, and sending rediculous oil to my intake. I am good with engines and cars, but really? 2nd set of turbos, and ihave to go through hell to even check them? I decided as soon as the turbo went, i love this damn car too much to ever get rid of it, so i started my complete modification stage to make my life easier and my car even more fun. Im worried a bit about the tune,especially since i cant seem to get thefile to checksum anything, or figure out how to datalog, but once i start her up tommorrow im planning on spending allweekend datalogging. :) enjoy, i know im rediculously stoked about this.
Title: Re: 01 audi s4 holset turbo Post by: marcellus on August 14, 2012, 11:24:14 PM What turbo are you using?
Title: Re: 01 audi s4 holset turbo Post by: ddillenger on October 20, 2012, 01:02:26 AM All of these single turbo threads have me eyeballing the PDR super hx-40 I have sitting in my backroom..........
Title: Re: 01 audi s4 holset turbo Post by: cactusgreens4 on October 22, 2012, 12:10:57 PM All of these single turbo threads have me eyeballing the PDR super hx-40 I have sitting in my backroom.......... DO IT! Title: Re: 01 audi s4 holset turbo Post by: ddillenger on October 22, 2012, 01:09:03 PM I'm thinking that since it's not vgt it may be a bit laggy-any thoughts? Its got a ported 16cm exhaust housing on it...
Title: Re: 01 audi s4 holset turbo Post by: cactusgreens4 on October 22, 2012, 05:36:08 PM I'm thinking that since it's not vgt it may be a bit laggy-any thoughts? Its got a ported 16cm exhaust housing on it... dont quote me on this but I think the variable geometry turbos are hard to control with our ecu's... or maybe thats just the 20v turbo I am thinking of. Title: Re: 01 audi s4 holset turbo Post by: Surferkirsch on October 23, 2012, 11:35:16 AM not sure what it was, i took it all back apart again.. it was around an hx-40. it was too laggy for my liking. im currently building up the bottom end, and then im going to go with a smaller turbo, and make some header manifolds for it to give more air.
Title: Re: 01 audi s4 holset turbo Post by: haggard69er on November 14, 2012, 02:13:43 PM the 16cm2 housing on a stock block is way to big imo. I am also exploring holset turbos and have decided on a hx35 (seven blade comp), it will flow around 60lbs which will be what i need to obtain my hp goal. you could also look for a smaller exhaust housing for your hx40 to help spool, but a smaller holset housing will most likely need to be machined out to fit. good luck!
Title: Re: 01 audi s4 holset turbo Post by: prj on November 15, 2012, 04:01:08 AM the 16cm2 housing on a stock block is way to big imo. What? I use these housings on the Audi 2.2T engine without any issue. The 16cm^2 is the smallest I use on those. Considering this has 2.7 liters displacement, then no, I would say 16 is even a little on the small side for a HX40. |