|
Title: Unable to full read flash B6 S4 'G'-box (8E0 910 560 G) Post by: MOB7D4 on September 29, 2014, 11:49:28 AM I'm able to connect to the ECU at highest baud rate. After connecting, I lower baud to 38,400. In the KWP2000 Flashing tab, I choose the 29F800BB memory layout to full read flash. This is as far as I've been able to go:
29/Sep/2014 11:46:13.106: USER: Starting to read data block. 29/Sep/2014 11:46:13.110: USER: Requesting upload from ECU for address range 0x00800000 to 0x00803FFF. 29/Sep/2014 11:46:13.113: LOG: Sent message with service ID RequestUpload 29/Sep/2014 11:46:13.139: LOG: Received message with service ID: NegativeResponse 29/Sep/2014 11:46:13.141: LOG: Received negative response for service ID: RequestUpload, with response code: NoProgram 29/Sep/2014 11:46:13.146: USER: Request upload from ECU failed, ECU reports service is not supported. Request upload may have been disabled by aftermarket engine software. -------------------------------------------------------------------------------------------------------------------------- 29/Sep/2014 11:46:13.148: USER: Reading ECU flash memory failed. Trying to force ECU to recognize read operation is complete. 29/Sep/2014 11:46:13.151: LOG: Validating flashed data checksum for address range 0x00900000 to 0x00900001. 29/Sep/2014 11:46:13.156: LOG: Sent message with service ID StartRoutineByLocalIdentifier 29/Sep/2014 11:46:13.178: LOG: Received message with service ID: StartRoutineByLocalIdentifierPositiveResponse 29/Sep/2014 11:46:13.183: LOG: Sent message with service ID RequestRoutineResultsByLocalIdentifier 29/Sep/2014 11:46:13.202: LOG: Received message with service ID: NegativeResponse 29/Sep/2014 11:46:13.204: LOG: Received negative response for service ID: RequestRoutineResultsByLocalIdentifier, with response code: BlockTransferDataChecksumError 29/Sep/2014 11:46:13.207: LOG: Checksum is incorrect. 29/Sep/2014 11:46:13.209: USER: Finished forcing ECU to recognize that failed read operation is complete. 29/Sep/2014 11:46:13.230: USER: Reading ECU flash memory failed. 29/Sep/2014 11:46:15.687: LOG: Sent message with service ID TesterPresent 29/Sep/2014 11:46:15.704: LOG: Received message with service ID: TesterPresentPositiveReponse 29/Sep/2014 11:46:17.388: LOG: User Prompt - Title: Reading ECU Flash Memory Complete Message: Reading ECU flash memory failed. Result: OK -------------------------------------------------------------------------------------------------------------------------- Title: Re: Unable to full read flash B6 S4 'G'-box (8E0 910 560 G) Post by: ddillenger on September 29, 2014, 12:38:52 PM The B6/B7 S4's don't usually cooperate with nefmoto I'm afraid.
Title: Re: Unable to full read flash B6 S4 'G'-box (8E0 910 560 G) Post by: MOB7D4 on September 29, 2014, 01:51:24 PM any suggestions?
Title: Re: Unable to full read flash B6 S4 'G'-box (8E0 910 560 G) Post by: nyet on September 29, 2014, 02:40:00 PM Head to audirevolution.net and ask sakimano for more information on how to tune b6/b7
He's super knowledgeable. Title: Re: Unable to full read flash B6 S4 'G'-box (8E0 910 560 G) Post by: MOB7D4 on September 29, 2014, 03:40:05 PM ;D Yeah, right! I've seen your post about the collection of mouth-breathers at AR...doesn't exactly inspire confidence. Couldn't open that site anyway, dead link or something.
So what options do I have? New ecu, store-bought tune, etc...just to stop the bitchin' of the rear O2 sensors?? What a pisser! >:( Title: Re: Unable to full read flash B6 S4 'G'-box (8E0 910 560 G) Post by: nyet on September 29, 2014, 03:51:52 PM Your only option is MPPS probably
Title: Re: Unable to full read flash B6 S4 'G'-box (8E0 910 560 G) Post by: ddillenger on September 29, 2014, 04:24:34 PM You can also bootmode it :)
|