Pages: [1]
Author Topic: DAMOS Motronic 4.3 / Volvo 850 T5  (Read 9943 times)
germi
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« on: January 17, 2012, 03:35:23 PM »

Im new to this forum so: Hello!

I have readen a lot now and searched everywhere i could but didnt found something.

Maybe one of you can provide me with a DAMOS for the old motronic 3.4 mounted in a Volvo 850 T5?

Every software in these cars contains tags with software partnumbers, hardware partnumbers, creation date and a stamp where is stored with which DAMOS they were created.
As example: 
"44/1/M4.3/19/117.X/DAMOS16//1603AE03/050696/" ,
"44/1/M4.3/19/117.4/DAMOS19//1901ME01/060795/" ,
"44/1/M4.3/19/117.X/DAMOS17//17A0ME01/021294/" ,

Anybody knows about anything about these DAMOS16, 17, 18, 19 ?


Best regards
Fabian

(Nice forum here, sorry about my bad english)


Logged
gremlin
Hero Member
*****

Karma: +194/-9
Offline Offline

Posts: 650


« Reply #1 on: January 17, 2012, 10:45:59 PM »

I have readen a lot now and searched everywhere i could but didnt found something.

http://trionic.mobixs.eu/
Logged
germi
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #2 on: January 18, 2012, 01:15:25 AM »

Hi

thanks for your answer.
Motronic Suite from this page youve sent me the link is what i worked till now.

i thought there is maybe a possibility to get deeper in the software of this motronic.
the most important maps are listed in motronic suite but there were so many "undocumented" maps too...
Logged
ohhello
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 28


« Reply #3 on: January 22, 2012, 10:47:22 PM »

Here's a tip, Motronic M4.3 is an ok fuel system. If you jump two pins together on a M4.4 ECU you can have a plug and play M4.4 ECU that is totally compatible with your M4.3 car.

From there I can help you with all the 'undefined' maps in M4.4

PM for further details...
Logged
germi
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #4 on: January 23, 2012, 11:08:01 AM »

thanks for the tip!
Logged
germi
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #5 on: February 04, 2012, 05:09:36 AM »

hello again.

i dont get an answer from "ohhello" anymore...
maybe someone other knows anything about this m4.3 to m4.4 swap?

which pads should i solder together?
and what should i do with the software then to delete SAS, EVAP and so on? DAMOS is necessary to do this.... am i right?

thanks
Logged
ohhello
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 28


« Reply #6 on: February 06, 2012, 09:12:32 PM »

Sorry been slammed.

I msg'd you on that topic. but there's quite a bit to it. The soldering on the board is easy but you'll need to know where in the code to remove the CEL trigger points.
Do you have DAMOS for M4.4?
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.041 seconds with 19 queries. (Pretty URLs adds 0.001s, 0q)