Pages: [1]
Author Topic: VAG ME7.5 bench reading/flashing w/KWP2000+ - suitable powersupply?  (Read 18448 times)
audidk
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7



I would like to do some experimental read/write to a spare ECU on the bench.

What are the requirements for a suitable powersupply, in terms of max. current? Am I better off with a spare 12V car battery?
Logged
kls
Full Member
***

Karma: +12/-0
Offline Offline

Posts: 97


« Reply #1 on: January 11, 2011, 05:45:16 PM »

Any regulated supply that provides 12 to 14 volts at with a current rating of at least 1 to 2 amps should be fine.
I think the key is that you want a regulated supply, not a standard "wall wart" that can have wildly varying voltage.
Logged
dan
Newbie
*

Karma: +2/-1
Offline Offline

Posts: 12


« Reply #2 on: January 11, 2011, 09:02:23 PM »

A computer power supply powered by a UPS would be my choice.
Logged
Jason
Hero Member
*****

Karma: +38/-0
Offline Offline

Posts: 500


Breaks everything!


« Reply #3 on: January 11, 2011, 11:32:24 PM »

If you go the computer power supply route, you can use an ATX power supply if you short the green wire on the ATX connector to any of the black wires as your "turn on".  (I think the green wire is pin 14 IIRC). 

 I just use a small SLA 12v battery with a trickle charger on it since the spare PSU I tried had a low voltage output of like 11.89V
Logged
audidk
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7


« Reply #4 on: January 12, 2011, 02:49:38 AM »

Thanx for the suggestions so far. Reliability is a top priority, price is second, but still a priority!

ATX power supply + UPS could do it, but an UPS is probably not cheap.

The SLA solution + trickle charger sounds good. And then I have a spare SLA if the one in the car let me down. Any idea to what happens, if the I experience a power outage during a flash, is the SLA sufficient to suppress any voltage spikes/drops?
Logged
dan
Newbie
*

Karma: +2/-1
Offline Offline

Posts: 12


« Reply #5 on: January 12, 2011, 09:35:07 AM »

Well, I was just making a wild assumption that anyone into computers enough to be flashing their own ECU's would have a UPS for their computer at home.

While the battery with trickle charger addresses a power outage, it does not do anything for voltage spikes. 

In all likelihood, either method will be fine, unless you are unlucky.
Logged
audidk
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7


« Reply #6 on: January 12, 2011, 10:25:34 AM »

My notebook got an built-in UPS :-)
Logged
Jason
Hero Member
*****

Karma: +38/-0
Offline Offline

Posts: 500


Breaks everything!


« Reply #7 on: January 12, 2011, 12:10:02 PM »

The trickle charger hasn't caused me any issues.  It is connected a small 4ah battery that you can buy at home depot/lowes for alarm systems/emergency lighting.

It's more prudent IMO to enable yourself to boot-mode flash in case of disaster.  Even with the cleanest, most voltage regulated power, you are still running the risk of windows blowing up when you flash and boot-mode is a fast and easy recovery method on the bench Smiley
Logged
Jason
Hero Member
*****

Karma: +38/-0
Offline Offline

Posts: 500


Breaks everything!


« Reply #8 on: January 13, 2011, 10:24:07 PM »

For grins, I took a new seasonic 750watt PSU and chopped it up.  It provides a little over 12v with a load on it, and is very stable - did several boot mode flashes, reads, and then 10 back to back NefMoto reads/writes...  no issue.  So, perhaps my old PSU was just junk?  Either case, if you have a PSU laying around, try it.  Short the green wire on the ATX header to an adjacent black wire, and then connect power to it - it will power up.. give her a whirl!
Logged
vag_tech
Newbie
*

Karma: +1/-0
Offline Offline

Posts: 3


« Reply #9 on: June 12, 2011, 09:17:31 PM »

Got one from radio shack, works great for bench flashing.

http://www.radioshack.com/product/index.jsp?productId=2103960&Camp=PPC%3AGoogle%3ATMProduct%3ABroad
Logged
Matt Danger
Full Member
***

Karma: +17/-1
Offline Offline

Posts: 116


« Reply #10 on: June 12, 2011, 09:54:10 PM »

I couldn't get reliable power from a few of the old ATX power supplies I used (from an old compaq & mac G4 tower). So I got this for around $20 shipped:

Pyramid PS3KX 3-Amp 12-Volt Power Supply
Logged
KmosK04
Full Member
***

Karma: +5/-10
Offline Offline

Posts: 97


« Reply #11 on: September 16, 2014, 02:40:21 AM »

What do you think about this guys? It will be good for bench flashing?

http://www.ebay.co.uk/itm/Mercury-650-656-Switch-Mode-13-8V-Bench-Top-Power-Supply-1-6m-Power-Lead-New-/131293693621?pt=UK_BOI_Electrical_Test_Measurement_Equipment_ET&hash=item1e91b6c6b5
Logged
turboat
Hero Member
*****

Karma: +45/-3
Offline Offline

Posts: 619


« Reply #12 on: September 16, 2014, 05:16:24 AM »

I use one of these: http://www.ebay.com/itm/Farnell-Instruments-Dual-Stabilized-Voltage-Power-Supply-LT30-2-220V-/301144489257?pt=LH_DefaultDomain_0&hash=item461d9c3d29

Overkill, but its nice having ammeter so you can see what the ecu is doing Smiley
Logged
vwaudiguy
Hero Member
*****

Karma: +53/-37
Offline Offline

Posts: 2024



« Reply #13 on: September 16, 2014, 01:12:35 PM »

Have good luck with this. Cheap and portable

http://laptopchargerfactory.com/syncmaster-150mp
Logged

"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.06 seconds with 16 queries. (Pretty URLs adds 0s, 0q)