NefMoto > Technical > Cluster and Immobilizer (Moderator: ddillenger) > MK2 Golf 1.8T Conversion Immobilizer Issue ME7.5
Pages: [1]
« previous next »
Author Topic: MK2 Golf 1.8T Conversion Immobilizer Issue ME7.5  (Read 4064 times)
motorsportsz
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 13
« on: June 17, 2018, 08:26:06 PM »
Hiya guys

i have a mk2 golf running a 1.8t BAM engine. Attached is the original eeprom and the one i modified. I am using TL866A programmer as it is the only thing i have with me at the moment

when write the immo off file. the car starts then cuts out giving fault codes. Fuel Pump Kicks in fine

P1649 Powertrain Data Bus Missing Message from ABS ECU
P1523 Crash Signal from Airbag ECU Implausible Signal
p1650 Powertrain Data Bus Missing Message from Instrument Cluster

We have another car with a similar conversion, when his ecu is used, the car runs fine. I cannot really open his ecu due to it having a warranty tamperproof label on it with his tuning company
Logged
k0mpresd
Hero Member
*****

Karma: +146/-54
Offline Offline

Posts: 1655
« Reply #1 on: June 18, 2018, 01:37:37 AM »
you need many more modifications to the ecu files than simply disabling immo for a proper conversion into older chassis.
Logged
elektronik13
Full Member
***

Karma: +10/-36
Offline Offline

Posts: 204
« Reply #2 on: June 18, 2018, 02:28:42 AM »
Quote from: motorsportsz on June 17, 2018, 08:26:06 PM
Hiya guys

i have a mk2 golf running a 1.8t BAM engine. Attached is the original eeprom and the one i modified. I am using TL866A programmer as it is the only thing i have with me at the moment

when write the immo off file. the car starts then cuts out giving fault codes. Fuel Pump Kicks in fine

P1649 Powertrain Data Bus Missing Message from ABS ECU
P1523 Crash Signal from Airbag ECU Implausible Signal
p1650 Powertrain Data Bus Missing Message from Instrument Cluster

We have another car with a similar conversion, when his ecu is used, the car runs fine. I cannot really open his ecu due to it having a warranty tamperproof label on it with his tuning company
this ecu can not be used for this car
here's immo off
« Last Edit: June 18, 2018, 02:33:58 AM by elektronik13 » Logged
motorsportsz
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 13
« Reply #3 on: June 18, 2018, 04:50:54 AM »
Quote from: k0mpresd on June 18, 2018, 01:37:37 AM
you need many more modifications to the ecu files than simply disabling immo for a proper conversion into older chassis.

Yes I know this as the car was running a emerald ecu prior to this but now want to get it started with this me7.5. Like I said the other me7.5 ecu starts the car fine but it’s off another car. How do I get this ecu to start the car ?
Also would like to add the clusters are still original

Cheers
« Last Edit: June 18, 2018, 04:52:57 AM by motorsportsz » Logged
motorsportsz
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 13
« Reply #4 on: June 18, 2018, 04:55:58 AM »
Can it be a checksum issue? I’ve just noticed after plugged into the car then read the 95040 with tl866a the two bytes that are meant to be 02 change to 04
Logged
_nameless
Hero Member
*****

Karma: +342/-466
Offline Offline

Posts: 2802
« Reply #5 on: June 18, 2018, 06:57:10 AM »
On block 91 in adaptations check what it says. For immo off the value should be 1. It's 4 bites that change for immo off if you're using a chip burner be sure to load your new file before writing otherwise you'll just be writing back the ori. If you need a swap file for the bam pm me Ivan help you out
Logged
Giving your mom a tuneup
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 28, 2024, 09:52:01 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.028 seconds with 18 queries. (Pretty URLs adds 0.001s, 0q)