Dev Blog
Forum
Wiki
About
NefMoto
>
Technical
>
Tuning
>
possible to run aeb m3.82 file on m5.92 aeb ecu ???
Pages: [
1
]
« previous
next »
Author
Topic: possible to run aeb m3.82 file on m5.92 aeb ecu ??? (Read 7742 times)
xxx8indxxx
Full Member
Karma: +0/-0
Offline
Posts: 115
possible to run aeb m3.82 file on m5.92 aeb ecu ???
« on: June 23, 2012, 09:31:52 AM »
seeing that i cannot find a damos or mappack for my 558 m ecu i took the file off my tuned 558m ecu and compared it to my stock 558m to help create a map pack it is a very slow process ..... i heard of someone using a m3.82 file on a m5.92 ecu and it ran fine it just had no diagnostic port im wondering if the diagnostic port info can be pasted from M5.92 FILE TO A M3.82 in order to have the obd port
Logged
pvl
Sr. Member
Karma: +32/-1
Offline
Posts: 350
Re: possible to run aeb m3.82 file on m5.92 aeb ecu ???
« Reply #1 on: July 01, 2012, 05:18:14 PM »
If you have 2 ecu's, you can test it. Don't forget the eeprom, as this might be the issue of obd-diags
The hardware is nearly the same, so should be very doable.
Logged
xxx8indxxx
Full Member
Karma: +0/-0
Offline
Posts: 115
Re: possible to run aeb m3.82 file on m5.92 aeb ecu ???
« Reply #2 on: July 01, 2012, 05:27:26 PM »
I'll have to try it I can always boot mode and refashio
My original
Logged
xxx8indxxx
Full Member
Karma: +0/-0
Offline
Posts: 115
Re: possible to run aeb m3.82 file on m5.92 aeb ecu ???
« Reply #3 on: July 02, 2012, 05:40:52 AM »
Do you think I willll have to pad the file to be 256k I don't think mops will write the file unless it's the right size
Logged
pvl
Sr. Member
Karma: +32/-1
Offline
Posts: 350
Re: possible to run aeb m3.82 file on m5.92 aeb ecu ???
« Reply #4 on: July 02, 2012, 04:48:13 PM »
Hi,
I missed that last .2 in your ecu-generation. Use a M3.8.3-file for the M5.92
Case sorted
If you need one, i can up one.
Cheers,
PvL
Logged
xxx8indxxx
Full Member
Karma: +0/-0
Offline
Posts: 115
Re: possible to run aeb m3.82 file on m5.92 aeb ecu ???
« Reply #5 on: July 02, 2012, 04:59:57 PM »
I'm trying to use a 3.82 file because I have the damos for it I haven't found a damos or map pack for 3.83 or5.92
Logged
prj
Hero Member
Karma: +1072/-481
Offline
Posts: 6037
Re: possible to run aeb m3.82 file on m5.92 aeb ecu ???
« Reply #6 on: July 03, 2012, 03:53:18 AM »
3.8.2 will not be possible to use.
3.8.3 you can use.
They are very similar structure, you can find all the maps in 3.8.3 easily with the 3.8.2 DAMOS.
Logged
PM's will not be answered, so don't even try.
Log your car properly
-
WinOLS database
-
Tools/patches
xxx8indxxx
Full Member
Karma: +0/-0
Offline
Posts: 115
Re: possible to run aeb m3.82 file on m5.92 aeb ecu ???
« Reply #7 on: July 03, 2012, 06:15:09 AM »
ok in short here is waht i did i took a 557b 3.82 file in winols i opened the project properties and its file size is 20000 so i doubled it to 40000 and filled the end of the file with ff then i used mpps to write to my ecu went successfully BUT lol the car did start for about 2 seconds so either the immo stopped it or something in the programming stopped it from running but it wasnt a total fail
Logged
prj
Hero Member
Karma: +1072/-481
Offline
Posts: 6037
Re: possible to run aeb m3.82 file on m5.92 aeb ecu ???
« Reply #8 on: July 03, 2012, 06:21:11 AM »
Any fault codes?
Logged
PM's will not be answered, so don't even try.
Log your car properly
-
WinOLS database
-
Tools/patches
xxx8indxxx
Full Member
Karma: +0/-0
Offline
Posts: 115
Re: possible to run aeb m3.82 file on m5.92 aeb ecu ???
« Reply #9 on: July 03, 2012, 06:28:09 AM »
with the 557b file on that ecu it will not let you use the obd port to read fault codes i dont know why the reason i wanted to try this is i was searching thru forums and i read that someone accidently did this and they said there car ran but could not use the obd port i wonder what could cause the port to go dead i wonder if 3.82 and 5.92 use a diff pin for diagnostics ?
Logged
prj
Hero Member
Karma: +1072/-481
Offline
Posts: 6037
Re: possible to run aeb m3.82 file on m5.92 aeb ecu ???
« Reply #10 on: July 03, 2012, 07:07:10 AM »
Just use 3.8.3...
Logged
PM's will not be answered, so don't even try.
Log your car properly
-
WinOLS database
-
Tools/patches
Pages: [
1
]
Print
« previous
next »
Jump to:
Please select a destination:
-----------------------------
General
-----------------------------
=> Introductions
=> General Discussion
-----------------------------
Noob Zone
-----------------------------
=> Noob Questions
=> Noob Guides and FAQs
-----------------------------
Technical
-----------------------------
=> NefMoto Software
=> Tuning
===> Documents & Helpers & How To's
===> Community Projects
=> Diagnostics
=> Flashing and Chipping
=> Cluster and Immobilizer
===> ECU EEPROM images
===> Original Cluster dumps
===> Original Cluster dump requests
=> Data Logging
=> Reverse Engineering
=> Communication Protocols
-----------------------------
ECU Files
-----------------------------
=> ECU Definition Files
===> ECU Definition File Requests
=> Original ECU Files
===> Original ECU File Requests
=> Checksum Update Requests
-----------------------------
Vehicles
-----------------------------
=> Vehicle Tech
=> Project Cars
-----------------------------
Regional
-----------------------------
=> Canadian Regional Discussion
=> US Regional Discussion
-----------------------------
Classifieds
-----------------------------
=> For Sale
=> Wanted
=> Services
-----------------------------
Miscellaneous
-----------------------------
=> Off Topic
=> Forum Tech Support
=> Bizarro Messages Posted by Bots and Spammers
Navigation
Home
Help
Login
Register
Personal Tools
November 27, 2024, 01:51:02 AM
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email?
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Search
Advanced Search
Loading...