NefMoto > Noob Zone > Noob Questions (Moderator: turboat) > LDRXN - Strange values
Pages: [1]
« previous next »
Author Topic: LDRXN - Strange values  (Read 1238 times)
Renegade187
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 19
« on: August 10, 2023, 03:49:46 AM »
Hi All,
I am trying to interpret this table but the values look very strange.  My ecu is a ME7.6.2 - Opel.
For the x axis which is the RPM the following shows:  54.75, 182.500, 7460, 15677.500, 12287, 54.750, 16188.500, 10689......
On the z axis the values where supposed to % but show as follows corresponding to the x axis values above:  12.0003, 0.0000, 12.0003, 0.0469, 12.0471, 0.0000

offset on x axis is 0.25*eprom
offset on z axis is 0.023438*eprom

Is the offset correct - please help
Logged
aef
Hero Member
*****

Karma: +69/-46
Offline Offline

Posts: 1601
« Reply #1 on: August 10, 2023, 05:23:14 AM »
No way to help you because you didnt upload a file and adress of where you think ldrxn is
Logged
Renegade187
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 19
« Reply #2 on: August 10, 2023, 06:11:58 AM »
apologies: the file as now been added

The start address shows as: A6342 from the hexdumpcursor

I also read somewhere that for the 7.6.2, the LDRXN is replaced by the KFRLSNT @ address - ADCC4

TIA
Logged
fknbrkn
Hero Member
*****

Karma: +186/-24
Offline Offline

Posts: 1455


mk4 1.8T AUM
« Reply #3 on: August 10, 2023, 07:58:59 AM »
Its obviously wrong defined / non exist
Logged
Silencesilja
Newbie
*

Karma: +2/-2
Offline Offline

Posts: 10
« Reply #4 on: August 10, 2023, 11:14:06 AM »
You read that right, there is no LDRXN in that SW

KFRLSNT - ADCC4 16bit LoHi ( 16x8 )  factor=0.023438*Eprom
X-Axis(U/min) - ADCA4 16bit LoHi ( 1x16 )  factor=0.25*Eprom
Y-Axis(Grad C) - ADC9C 8bit ( 1*8 )  factor=0.75*Eprom-48
« Last Edit: August 10, 2023, 11:16:41 AM by Silencesilja » Logged
Renegade187
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 19
« Reply #5 on: August 10, 2023, 12:04:26 PM »
Quote from: Silencesilja on August 10, 2023, 11:14:06 AM
You read that right, there is no LDRXN in that SW

KFRLSNT - ADCC4 16bit LoHi ( 16x8 )  factor=0.023438*Eprom
X-Axis(U/min) - ADCA4 16bit LoHi ( 1x16 )  factor=0.25*Eprom
Y-Axis(Grad C) - ADC9C 8bit ( 1*8 )  factor=0.75*Eprom-48

Thank you very much

One more question,  the TVUB on this software is also very strange.   It was supposed to be voltage and injector ms.  I'm seeing degrees Celsius on the one axis and ms on the z axis.
This is at address A3FE2.  the graph title says intake air temp / ms.
Is this correct?  Does this sw incorporate injection time vs voltage?
Logged
Silencesilja
Newbie
*

Karma: +2/-2
Offline Offline

Posts: 10
« Reply #6 on: August 10, 2023, 12:53:24 PM »
Sure it has voltage correction..
TVUB - A3F22 16bit LoHi ( 5x1 ) factor=0.002667*Eprom
X-Axis - A3F1D 8bit factor=0.0681*Eprom
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 26, 2024, 12:03:04 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.02 seconds with 17 queries. (Pretty URLs adds 0s, 0q)