bombis
Jr. Member
Karma: +0/-2
 Offline
Posts: 31
|
 |
« on: September 11, 2024, 05:39:19 AM »
|
|
|
HI,
How to find location for KFLDRL? (my mappack dont find this)
I know the map is 10x16. 16bit. Factor 0.005
ECU 4B0906018DC
Found this map right below kfldimx
|
|
|
|
« Last Edit: September 16, 2024, 11:40:39 AM by bombis »
|
Logged
|
|
|
|
bombis
Jr. Member
Karma: +0/-2
Offline
Posts: 31
|
|
« Reply #1 on: September 11, 2024, 05:43:28 AM »
|
|
|
my ecu
|
|
|
|
|
Logged
|
|
|
|
|
IamwhoIam
|
|
« Reply #2 on: September 11, 2024, 07:46:24 AM »
|
|
|
If you think the axis in KFLDRL is throttle angle, that tells me that you shouldn't be looking for KFLDRL in the first place but rather going through the S4 wiki, all the pinned posts on here and a decent Funktionsrahmen. Hopefully you realize that before you go and call me names.
|
|
|
|
|
Logged
|
I have no logs because I have a boost gauge (makes things easier)
|
|
|
bombis
Jr. Member
Karma: +0/-2
Offline
Posts: 31
|
|
« Reply #3 on: September 11, 2024, 11:42:06 AM »
|
|
|
I know the table is duty cycle %, for wastegate control. I need to reduce it at high rpm, because i have external wastegate with stiffer spring. Therefore i need lower dutycycle. I only need the location for the map. I¨ve read some of the litterature, about the PID. The result; ldtvr_w is input  |
|
|
|
« Last Edit: September 11, 2024, 12:33:35 PM by bombis »
|
Logged
|
|
|
|
|
gremlin
|
|
« Reply #4 on: September 11, 2024, 03:53:52 PM »
|
|
|
KFLDRL[%]=f(nmot_w, lvtvr_w) -> 0x1EBB2
Axis nmot -> 0x134BE
Axis lvtvr -> 0x1EDC0
BTW the "more stiffer spring" means some changes in i, p, d factors of PID-Control.
To make boost control flawless may be isn't enough to patch only KFLDRL.
KFLDRQ0, KFLDRQ1 and KFLDRQ2 may need some corrections also.
|
|
|
|
« Last Edit: September 11, 2024, 04:13:50 PM by gremlin »
|
Logged
|
|
|
|
bombis
Jr. Member
Karma: +0/-2
Offline
Posts: 31
|
|
« Reply #5 on: September 12, 2024, 04:46:20 AM »
|
|
|
thanks a lot Gremlin.
|
|
|
|
« Last Edit: September 16, 2024, 11:55:36 AM by bombis »
|
Logged
|
|
|
|
bombis
Jr. Member
Karma: +0/-2
Offline
Posts: 31
|
|
« Reply #6 on: September 16, 2024, 11:50:32 AM »
|
|
|
Looks like wastegate dutycycle is living its own life
I did reduce imx and kfldrl, but gets exactly the same dc.
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #7 on: September 16, 2024, 12:17:33 PM »
|
|
|
|
|
|
|
|
Logged
|
ME7.1 tuning guideECUx PlotME7Sum checksumTrim heatmap toolPlease do not ask me for tunes. I'm here to help people make their own. Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
|
|
|
bombis
Jr. Member
Karma: +0/-2
Offline
Posts: 31
|
|
« Reply #8 on: September 16, 2024, 02:31:30 PM »
|
|
|
sorry
insert; log
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #9 on: September 16, 2024, 10:51:25 PM »
|
|
|
There is nothing good going on there. Put everything back to stock and start again.
|
|
|
|
|
Logged
|
ME7.1 tuning guideECUx PlotME7Sum checksumTrim heatmap toolPlease do not ask me for tunes. I'm here to help people make their own. Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
|
|
|
bombis
Jr. Member
Karma: +0/-2
Offline
Posts: 31
|
|
« Reply #10 on: September 19, 2024, 10:35:45 AM »
|
|
|
That solved the problem nyet  Boost pressure follows boost pressure desired much better now |
|
|
|
|
Logged
|
|
|
|
fknbrkn
Hero Member
Karma: +185/-21
Offline
Posts: 1447
mk4 1.8T AUM
|
|
« Reply #11 on: September 19, 2024, 12:04:21 PM »
|
|
|
That solved the problem nyet Boost pressure follows boost pressure desired much better now low wgdc at spool, why? imx super-weirdo also +3 deg advance @5000 is way too low wiki is pretty clear with tighten springs and all you need is KFVPDKSE axis, imx axis/values and DRL linearising (or imx linearising in case of precontrol way) |
|
|
|
|
Logged
|
|
|
|
bombis
Jr. Member
Karma: +0/-2
Offline
Posts: 31
|
|
« Reply #12 on: September 20, 2024, 06:40:21 AM »
|
|
|
low wgdc at spool, why?
imx super-weirdo
also +3 deg advance @5000 is way too low
wiki is pretty clear with tighten springs
and all you need is KFVPDKSE axis, imx axis/values and DRL linearising (or imx linearising in case of precontrol way)
imx and drl was stock. Raised them to get 95% wgdc at spool (y) Increased timing to 9,75@5000. why is it dropping 3-7deg occasionally? 0 ignition retard, dwkrz |
|
|
|
|
Logged
|
|
|
|
|
