NefMoto > Technical > Tuning > Rev limiter
Pages: [1]
« previous next »
Author Topic: Rev limiter  (Read 8059 times)
littco
Hero Member
*****

Karma: +52/-7
Offline Offline

Posts: 903
« on: March 29, 2013, 02:38:27 PM »
Is there a way of getting a hard cut rev limiter? Rather than running up to the limiter at 300rpm before and feeling it back off is it possible to get it run up and then cut at the limit dead. I assume it may need some routine change on the rpm limiter to cut ignition but before I go down that route just wondered if any one had a pearls of wisdom I've over looked.
Logged
Axis
Full Member
***

Karma: +4/-4
Offline Offline

Posts: 91
« Reply #1 on: March 29, 2013, 02:46:10 PM »
Read FR or the following thread and you will find what you need.
nefariousmotorsports.com/forum/index.php?topic=151.0
Logged
littco
Hero Member
*****

Karma: +52/-7
Offline Offline

Posts: 903
« Reply #2 on: March 29, 2013, 03:40:12 PM »
Quote from: littco on March 29, 2013, 02:38:27 PM
Is there a way of getting a hard cut rev limiter? Rather than running up to the limiter at 300rpm before and feeling it back off is it possible to get it run up and then cut at the limit dead. I assume it may need some routine change on the rpm limiter to cut ignition but before I go down that route just wondered if any one had a pearls of wisdom I've over looked.

Mmm
No help...
Logged
Rick
Hero Member
*****

Karma: +63/-4
Offline Offline

Posts: 704
« Reply #3 on: March 29, 2013, 03:41:24 PM »
You can use fuel cut to give you a harder limiter.  If you want to bounce of it, you need custom code.

Rick
Logged
littco
Hero Member
*****

Karma: +52/-7
Offline Offline

Posts: 903
« Reply #4 on: March 29, 2013, 03:46:43 PM »
Quote from: Rick on March 29, 2013, 03:41:24 PM
You can use fuel cut to give you a harder limiter.  If you want to bounce of it, you need custom code.

Rick

Thanks Rick.. That was the answer I was looking for.
Logged
matchew
Hero Member
*****

Karma: +47/-22
Offline Offline

Posts: 503
« Reply #5 on: March 29, 2013, 03:48:09 PM »
Even though it is wrong?
Logged
littco
Hero Member
*****

Karma: +52/-7
Offline Offline

Posts: 903
« Reply #6 on: March 29, 2013, 03:58:47 PM »
Quote from: matchew on March 29, 2013, 03:48:09 PM
Even though it is wrong?


Please tell me more.

I'm always open to suggestions and seemingly as Rick does know what he's talking about most of the time I'd have to listen to him over a " read FR comment"!

I was hoping someone might have a simple answer for me rather than the cryptic " you must learn young Jedi" none sense that turns up every now and then...
Logged
Axis
Full Member
***

Karma: +4/-4
Offline Offline

Posts: 91
« Reply #7 on: March 29, 2013, 04:03:39 PM »
But why would you want a limiter that are more prune to destroy engine mounts and other stuff? Why is it not enough to decrease the mentioned 300rpm?
Logged
littco
Hero Member
*****

Karma: +52/-7
Offline Offline

Posts: 903
« Reply #8 on: March 29, 2013, 04:18:29 PM »
Quote from: Axis on March 29, 2013, 04:03:39 PM
But why would you want a limiter that are more prune to destroy engine mounts and other stuff? Why is it not enough to decrease the mentioned 300rpm?


Because I want to know if its possible , for no other reason. The 300rpm just seems soft...
Logged
Rick
Hero Member
*****

Karma: +63/-4
Offline Offline

Posts: 704
« Reply #9 on: March 29, 2013, 04:22:11 PM »
Quote from: matchew on March 29, 2013, 03:48:09 PM
Even though it is wrong?


What's wrong?
Logged
Snow Trooper
Hero Member
*****

Karma: +90/-24
Offline Offline

Posts: 689


WWW
« Reply #10 on: March 29, 2013, 10:05:25 PM »
Play with DNMAXH, I run my car at 50 compared to the stock 200.
Logged
cartoons?
6A 61 72 65 64 40 76 6C 6D 73 70 65 63
littco
Hero Member
*****

Karma: +52/-7
Offline Offline

Posts: 903
« Reply #11 on: March 30, 2013, 07:35:46 AM »
Quote from: Snow Trooper on March 29, 2013, 10:05:25 PM
Play with DNMAXH, I run my car at 50 compared to the stock 200.

Thank you.. I will give it ago...
Logged
krazydbiker
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 202
« Reply #12 on: March 31, 2013, 07:33:19 AM »
i have tried the dnmaxh a few times for mine, only for the first second or two its a hard limiter, then it seems to go soft Sad, so it seems in my case custom code is needed, or atleast modification of the original code

edit : i did not read post fully, to early Undecided... snow troopers method worked for me up high, but i turned it back after almost hitting the windshield a few times, its definitely a HARD limit
« Last Edit: March 31, 2013, 07:59:09 AM by krazydbiker » Logged
Axis
Full Member
***

Karma: +4/-4
Offline Offline

Posts: 91
« Reply #13 on: March 31, 2013, 07:42:20 AM »
Are you guys sure you are not talking about gear dependent torque limiter at high rpm?
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 27, 2024, 01:44:07 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.026 seconds with 17 queries. (Pretty URLs adds 0s, 0q)