Pages: [1]
Author Topic: Fueling not matching requested  (Read 5127 times)
savages4
Sr. Member
****

Karma: +10/-5
Offline Offline

Posts: 251


« on: July 14, 2013, 11:52:21 PM »

Just got my wideband, fuel pump etc in and I'm trying to dial in my fueling finally.  I was curious what maps you would suggest correcting to get the fueling to follow requested more.  I'm using an RS4 MAF and bosch rs4 maf sensor and I have copied over MLOFS, KFKHM, and MLHFM from K-box rs4 bin.  Also, is it safe to copy KFLF and KFLF axis's from the k-box file, I haven't done this yet but thinking of trying it to see if it helps however after looking at the values they are higher which would seem to throw it even richer which isn't what I need.

Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Online Online

Posts: 12268


WWW
« Reply #1 on: July 15, 2013, 09:16:14 AM »

Thats actually pretty close.

Just pull a bit through KFLF or KFKHM.

Also, log ps_w to make sure you aren't at its limit.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
savages4
Sr. Member
****

Karma: +10/-5
Offline Offline

Posts: 251


« Reply #2 on: July 15, 2013, 11:12:13 AM »

So when adjusting it a bit through KHKFM should I do the entire load range or just the high load parts?
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Online Online

Posts: 12268


WWW
« Reply #3 on: July 15, 2013, 11:32:12 AM »

I'd stick to load areas you have logged.

That said, you should attempt to keep it relatively smooth.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
pablo53
Full Member
***

Karma: +5/-1
Offline Offline

Posts: 94


« Reply #4 on: July 15, 2013, 09:13:02 PM »

No issues using the k box axes but don't go beyond the K-box upper load line of 191.25.



 
Logged
savages4
Sr. Member
****

Karma: +10/-5
Offline Offline

Posts: 251


« Reply #5 on: July 15, 2013, 11:42:33 PM »

Adjusted KFKHFM and looks like I got it pretty dialed, just need to get desired leaned up a bit over 4500 rpm..

Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Online Online

Posts: 12268


WWW
« Reply #6 on: July 16, 2013, 09:59:48 AM »

Awesome! nice work.

btw.. thats pretty rich... might want to consider not going any richer than 11.5 ...

Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
julex
Hero Member
*****

Karma: +79/-4
Offline Offline

Posts: 923


« Reply #7 on: July 16, 2013, 11:18:47 AM »

Awesome! nice work.

btw.. thats pretty rich... might want to consider not going any richer than 11.5 ...



I concur. My car usually starts bogging down at anything richer than 10.8, but that's with 2 x 630cc of W/M so it would probably go down a bit more on pure gas.
« Last Edit: July 16, 2013, 11:20:40 AM by julex » Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.021 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)