Pages: [1]
Author Topic: Running lean in boost  (Read 6918 times)
nagoL
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 3


« on: October 18, 2013, 02:44:54 PM »

Guys,

I'm running a bit lean while in boost around 12.8 and I believe I should be in the 11's - I've also got a weird issue where if I throw her into neutral an coast to a red light she tends to idle as if I have a vac leak and my wide band runs up to 17s and back down over and over. It will do this consistently until I get under around 15 mph to a stopping point then shes back to a normal idle.  I believe this also has to do with my AFR.   Any help would be greatly appreciated.  Specs are shown below and I can supply my recent logs if needed.

'03 VW 1.8 GTI  - Eurodyne Maestro Software
  - GT3071r turbo w/ billet wheel
  - Tial stainless steel GT3- v-band exhaust housing
  - Tial MV-R 44mm wastegate
  - InjectorDynamics ID725 injectors
  - APR intake manifold
  - 3" exhaust system. no cat. Magnaflow resonator and muffler. Dual tips.
  - Eurojet grenade Diverter Valve
  - Greddy 500hp core
  - Devils Own's DVC-30 water methanol
  - 42DD oil catch can
  - Aeromotive 340 fuel pump
  - 2.0T coil pack upgrade with IE spacers
  - Fluidampr lower pulley
  - Brute 19mm Connection rods



« Last Edit: October 18, 2013, 05:12:58 PM by nagoL » Logged
adam-
Hero Member
*****

Karma: +124/-33
Offline Offline

Posts: 2179


« Reply #1 on: October 18, 2013, 02:46:40 PM »

Why enrich then lean out towards redline?
Logged
terminator
Sr. Member
****

Karma: +15/-4
Offline Offline

Posts: 425


« Reply #2 on: October 18, 2013, 04:35:13 PM »

Of course, because you have made it lean  Wink.

KFLF is not AFR request.
0.85 means 14.7(aprox) + 15% = around 16.9 without lambda correction.

But if you use methanol you should lean it a little via KFLF or KFKHFM to prevent misfires.


By the way, what software do you use? ECM Titanium also "think" that KFLF = AFR request.
« Last Edit: October 18, 2013, 04:37:40 PM by terminator » Logged
nagoL
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 3


« Reply #3 on: October 18, 2013, 05:10:26 PM »

Hrm, well i run 14.7 when cruising and i thought 0.1000 was the desired lambda for 14.7

The software is Eurodyne Maestro
Logged
ddillenger
Hero Member
*****

Karma: +641/-21
Offline Offline

Posts: 5640


« Reply #4 on: October 18, 2013, 05:42:46 PM »

Think that is BTS...
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
B234R
Full Member
***

Karma: +11/-0
Offline Offline

Posts: 75


« Reply #5 on: October 18, 2013, 05:43:48 PM »

No!
Lambda 0,85 means:
14,7 AFR * 0,85 = AFR 12,5.

If you see 12,8 on your WB gauge, it can be due to a lot of things.
Request is AFR 12,5 from that map.

No rocket science.
Logged
nagoL
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 3


« Reply #6 on: October 18, 2013, 07:42:39 PM »

Eh, appreciate the patience everyone.  New to the tuning scene.

So, i need to tune more towards .78 request for this map if I want 11.5ish while in WOT (boost)?
Logged
RaraK
Hero Member
*****

Karma: +58/-2
Offline Offline

Posts: 539


« Reply #7 on: October 18, 2013, 09:32:28 PM »

.81-.82 max if you have meth as itll add an extra point or so depending on your nozzles.

Logged
terminator
Sr. Member
****

Karma: +15/-4
Offline Offline

Posts: 425


« Reply #8 on: October 19, 2013, 06:07:38 AM »

Think that is BTS...
Yeap, I was wrong  Grin

No!
Lambda 0,85 means:
14,7 AFR * 0,85 = AFR 12,5.

Its for BTS or LAMFA, not for KFLF, like I thought) Strange thoughts  Grin
Logged
userpike
Hero Member
*****

Karma: +22/-1
Offline Offline

Posts: 763


« Reply #9 on: October 19, 2013, 07:51:33 AM »

There is a huge Eurodyne thread on VWVortex.
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.041 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)