Pages: [1]
Author Topic: 1.8t AVJ  (Read 5649 times)
ijik
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 8


« on: February 16, 2016, 07:25:33 AM »

Hello, someone could help me find LAMFA map in my ecu file? I think address this map is 26BE2 but i'm not sure
Regards Smiley
Logged
adam-
Hero Member
*****

Karma: +123/-33
Offline Offline

Posts: 2179


« Reply #1 on: February 16, 2016, 10:07:11 AM »

I've got 1D216, axis at 1D1FA.
Logged
ijik
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 8


« Reply #2 on: February 17, 2016, 02:39:38 AM »

hymm you're right Smiley When i wos looking for this map suggesting a Community Project 1.8t Stage 1, there are some diffrent address than in my file. I am a beginner and I did not know that the same maps can be so far apart in similar files Shocked
So thank you very much for your help!! Wink Now I will seek further map such as LDRXN LDRXNZK KFZW/2 KFLDHBN
Regards
Logged
adam-
Hero Member
*****

Karma: +123/-33
Offline Offline

Posts: 2179


« Reply #3 on: February 17, 2016, 02:57:04 AM »

Have you even attempted?
Logged
ijik
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 8


« Reply #4 on: February 17, 2016, 03:19:15 AM »

No, it's my first steps with ECU. I am a student interested in electronics and automotive. Analyzed community projects (1.8t and 2.7t) and am in the process of learning Advisory: Understanding ECU Remapping: The Audi TT 1.8T Variants / Motronic ME7.x, this is interesting stuff but I can see that little I can. I learned the basics Winols and I'm trying to finding and understanding some maps. When I read the articles I see that the important thing are the logs, but I did not do them yet and do not know which blocks i need to login.  So many questions, so few answers Smiley
Logged
jimmcgee5
Full Member
***

Karma: +7/-7
Offline Offline

Posts: 201


« Reply #5 on: February 17, 2016, 06:19:14 AM »

here knock yourself out  Cheesy
Logged
ijik
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 8


« Reply #6 on: February 17, 2016, 08:20:45 AM »

ol shittttt a lot of maps Grin thanks a lot bro Smiley
I think with a warm-up try to remove the rear 02 sensor, on Tuning-S4wiki is a lot about this, we'll see if I can make it Smiley The next step will be LAMFA modifications.
Regards!
Logged
ijik
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 8


« Reply #7 on: February 18, 2016, 10:44:37 AM »

I have a few questions...
1. My LAMFA map has strange x axis 85 87,5 90 92,5 95 97,5. I would like to be 50 60 70 80 90 and 97.5 like in community project. It is bad factory (i use 0,003052)? I don't know.
2. When i change something in my file and do checksum and is correct. Can i write this file to my ecu or i should check this file some other checksummer? I use Winols 2.24 end NefMoto VW Audi ME7 ECU Flasher 1.9.3.2?
Can anyone help?
Logged
ijik
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 8


« Reply #8 on: March 09, 2016, 08:57:45 AM »

Hello
I made some changes in my ecu. Changes concern LAMFA and LDRXN, I think engine load is too large. Can someone look at it and prompt what else i should do with this file? This can be used for daily driving?
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.019 seconds with 17 queries. (Pretty URLs adds 0s, 0q)