|
dream3R
|
 |
« Reply #105 on: September 21, 2013, 06:34:03 AM »
|
|
|
KLine code may be in there but Volvo flash these controller with a SBL over CAN-BUS.
They reside on the low-speed, 125KBPS network.
Can you find any 'maps' per say?
|
|
|
|
|
Logged
|
|
|
|
jacob21
Newbie
Karma: +0/-0
 Offline
Posts: 5
|
|
« Reply #106 on: September 21, 2013, 09:44:31 AM »
|
|
|
A quick scan and the K-line stuff used in the VAG Gen1 controller is not there. The only K-line stuff appears to be a small KWP1281 function, just to read info and call a function which doesn't appear to be present, possible development stuff, not implemented in the production controllers.
If you're looking for maps, the data section is contained in the "DEM EXE.vbf-block2" file in the rar you posted. Disassembly will be needed to figure out the particular characteristics, etc., unless you have an a2l, etc. file.
|
|
|
|
|
Logged
|
|
|
|
|
dream3R
|
|
« Reply #107 on: September 21, 2013, 09:46:27 AM »
|
|
|
Cool, I know what I'll be trying to-do tonight...
IDA isn't easy though, any chance you can share a file correctly setup to give me a chance?
|
|
|
|
|
Logged
|
|
|
|
jacob21
Newbie
Karma: +0/-0
Offline
Posts: 5
|
|
« Reply #108 on: September 21, 2013, 03:55:51 PM »
|
|
|
Here's a bin that I believe is setup in the correct order, haven't created an ida file though.
|
|
|
|
|
Logged
|
|
|
|
|
dream3R
|
|
« Reply #109 on: September 22, 2013, 02:18:08 AM »
|
|
|
Thank you.
I cant find much but then I don't really know IDA.
|
|
|
|
|
Logged
|
|
|
|
|
dream3R
|
|
« Reply #110 on: October 29, 2013, 03:11:42 AM »
|
|
|
Anyone got any further with this. I'd really like to change my torque split.
|
|
|
|
|
Logged
|
|
|
|
ejg3855
Full Member
Karma: +6/-0
Offline
Posts: 123
|
|
« Reply #111 on: November 05, 2013, 05:33:45 AM »
|
|
|
yay guys, keep up the good work.
|
|
|
|
|
Logged
|
|
|
|
|
dream3R
|
|
« Reply #112 on: December 18, 2013, 09:51:36 AM »
|
|
|
yay guys, keep up the good work.
I've got my hands on one of these. Does anyone know the pinout for the 8 pin connector? I assume kline will be there. |
|
|
|
|
Logged
|
|
|
|
ejg3855
Full Member
Karma: +6/-0
Offline
Posts: 123
|
|
« Reply #113 on: December 30, 2013, 07:10:11 AM »
|
|
|
Haldex Pinouts:
T8 - Socket between car and control unit
T8/1, Red = Ign.
T8/2, Black = Gnd.
T8/3, White = BLS (brake light switch)
T8/4, Blue = HBLS (hand brake light switch)
T8/5, Brown = K-line (diagnostics)
T8/7, Blue/Grey = CAN low
T8/8, Blue/Orange = CAN high
T2 - Socket between control unit and feeder pump(pwm switched voltage)
T2/1, Yellow = Pump 1
T2/2, Yellow/Black = Pump 2
here. |
|
|
|
|
Logged
|
|
|
|
|
dream3R
|
|
« Reply #114 on: December 30, 2013, 07:44:56 AM »
|
|
|
Thanks, sorry missed that post. I'll try and bootmode the spare one I have here.
|
|
|
|
|
Logged
|
|
|
|
|
|
|
dream3R
|
|
« Reply #116 on: January 12, 2014, 04:26:52 PM »
|
|
|
Well no joy in my boot mode experiment. |
|
|
|
|
Logged
|
|
|
|
ejg3855
Full Member
Karma: +6/-0
Offline
Posts: 123
|
|
« Reply #117 on: April 05, 2014, 01:59:23 PM »
|
|
|
apparently United Motorsports has achieved this.
|
|
|
|
|
Logged
|
|
|
|
edgy
Full Member
Karma: +2/-0
Offline
Posts: 66
|
|
« Reply #118 on: May 21, 2014, 12:25:03 PM »
|
|
|
Threadsurrection...
Was going through some of my car stuff today and found two Haldex controllers. One has an internal memory fault, the other is a working backup for the one in my TT.
I'm going to tear into the bad one this afternoon a little and monkey with it.
If any of the highly experienced members here want me to send them the bad unit to research and see if we cant get the eeprom and flash read, please contact me. I'm interested in getting this undertaking back off the ground and add a chapter to the DIY tuning history books.
|
|
|
|
|
Logged
|
2002 S4 full stg 3
2001 S4 stg 2
2001 TT 225 stg 2
1988 80q 4.2
2005 A4 (the wife's)
|
|
|
ported2flow
Full Member
Karma: +2/-0
Offline
Posts: 78
|
|
« Reply #119 on: July 14, 2014, 05:35:30 AM »
|
|
|
Hey guys
If unitedmotorsport sorted this out then we have to get it working too!!
As far as I know customers are able to flash the haldex unit at home with their loaner tool.that means the customer plugs in the cable to the obd port and flash the file via obd
I know sounds easy so it has to be for customer that doesn't have a clue about tuning.has to be easy.
Back to the bootmode stuff.since most guys in this thread said there is an cr167 infineon like ecu in the haldex unit
Didn't anyone tried to connect to the unit with minimon??
The tool was made for this..
Let's get this back....
|
|
|
|
|
Logged
|
|
|
|
|
