Pages: [1]
Author Topic: Clueless and need all the help I can get!  (Read 5666 times)
Aneves
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 32


« on: September 06, 2016, 07:47:32 PM »

What's up guys? Have a mk4 vr6 looking to tune stock engine while learning, I'm building a turbo 2.8 vr6 that I would like to tune once I can get around tuning my own. All and any help greatly appreciated. Need help start to finish, hardware, software and know how!
Logged
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Online Online

Posts: 12270


WWW
« Reply #1 on: September 06, 2016, 07:53:34 PM »

One word of advice. Do not start buying parts until you have your tune fully planned out.

If you buy a random box of parts, and only after you installed them start to worry about your tune, you're fucked.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
Carsinc
Sr. Member
****

Karma: +17/-2
Offline Offline

Posts: 447


« Reply #2 on: September 07, 2016, 05:09:07 AM »

Nyet speaks the truth, that being said there are def some things that can be done.
I'd say its safe to build the bottom end, you know rods and pistons, if stock pitons
plan for a headspacer cause you will be wanting to lower the compression.
Other than that I'm going to tell you the same others will, to go from 0 to VRT in the
tuning world is far from easy and will most likely take years.
Logged
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Online Online

Posts: 12270


WWW
« Reply #3 on: September 07, 2016, 10:18:27 AM »

from 0 to VRT in the
tuning world is far from easy and will most likely take years.

x1000

Turboing an NA car is not a good way to start learning.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
vwaudiguy
Hero Member
*****

Karma: +53/-37
Offline Offline

Posts: 2024



« Reply #4 on: September 07, 2016, 10:57:17 AM »

plan for a headspacer

Try to avoid this. Do it right, or don't bother.
Logged

"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
Carsinc
Sr. Member
****

Karma: +17/-2
Offline Offline

Posts: 447


« Reply #5 on: September 07, 2016, 04:48:58 PM »

I agree but a headspacer is better than stock compression.
Logged
adam-
Hero Member
*****

Karma: +124/-33
Offline Offline

Posts: 2179


« Reply #6 on: September 08, 2016, 04:32:30 AM »

Doing it properly is also better than stock compression.
Logged
Aneves
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 32


« Reply #7 on: November 05, 2016, 03:42:08 PM »

As far as "hardware" I was speaking in terms of tuning electronically wise. Sorry for the mixup. Mechanically all hardware I have already been collecting it over the past months. I own a shop and have access lots of goodies. Vibrant sure helps a lot. My whole thing is that I would love to build a car and do everything myself, instead of subletting it out. All help greatly appreciated.


Sent from my iPad using Tapatalk
Logged
dokalanyi
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 119


« Reply #8 on: November 16, 2016, 07:59:38 AM »

Aneves,
Not sure what your tuning experience is, but if you're actually clueless as you say, one noob to another:

- Buy a stock 1.8T (K03(s), stock injectors)
- Swap it into your MK4
- Tune that to stage 1
- Change to bigger injectors and Turbo
- Tune to stage 3.

Revisit your VR6.

I could be wrong, but getting the hang of these things is difficult in easy level, you're playing God mode.
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.025 seconds with 16 queries. (Pretty URLs adds 0s, 0q)