Pages: [1] 2
Author Topic: 2005 VW Jetta GLI 1.8T AWP 180HP 06A 906 032 SM  (Read 16758 times)
All_Euro
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 15


« on: November 08, 2011, 01:04:38 PM »

Hi guys,

I'm new here and would like to start using ME7Logger. I believe I need the original BIN as a starting point... my ECU has been flashed by Unitronic already so it has security I'm told.

Any help would be appreciated.
Logged
Gonzo
Sr. Member
****

Karma: +20/-30
Offline Offline

Posts: 483


« Reply #1 on: November 08, 2011, 01:26:57 PM »

Version 040 or 030?
Logged
All_Euro
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 15


« Reply #2 on: November 08, 2011, 06:53:52 PM »

Hey, thanks for the quick reply. I'm actually not sure what you mean by Version 040 or 030… how do I find out Smiley
Logged
Gonzo
Sr. Member
****

Karma: +20/-30
Offline Offline

Posts: 483


« Reply #3 on: November 23, 2011, 01:51:45 PM »

I mean which revision/software version do you need? There is 0030 and 0040
Logged
carlossus
Sr. Member
****

Karma: +38/-0
Offline Offline

Posts: 394

Leon Curpa Stg1+


« Reply #4 on: November 23, 2011, 02:05:49 PM »

Hey, thanks for the quick reply. I'm actually not sure what you mean by Version 040 or 030… how do I find out Smiley

Buy your lovely cheap KKL cable, connect using lovely free NefMoto and your s/w version should be in the status window. Or, if it's an unmodified ECU then read out the original yourself!
Logged
All_Euro
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 15


« Reply #5 on: November 24, 2011, 01:00:58 PM »

Lucky for me I have a lovely blue cable Smiley The option to read the ECU isn't available when I connect but here's what I get…
 
KWP1281 connect info: °6A906032SM 1.8L R4/5VT     G03 0030
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP2000 session.
Sending start communication request.
Connected


So version 030 then?
Logged
carlossus
Sr. Member
****

Karma: +38/-0
Offline Offline

Posts: 394

Leon Curpa Stg1+


« Reply #6 on: November 24, 2011, 02:28:01 PM »

Yes.

No read option? Have you chosen a memory layout?
Logged
All_Euro
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 15


« Reply #7 on: November 24, 2011, 09:54:12 PM »

Ah, thanks for your patience guys. None of the memory layouts will stick, they all read something like this…

Validating flash memory starts at 0x00800000 and ends at 0x00900000.
Validation failed, ECU reports RequestUpload service is not supported. RequestUpload may have been disabled by aftermarket engine software.
100% complete.


Probably no surprise there. Any way around this?
Logged
carlossus
Sr. Member
****

Karma: +38/-0
Offline Offline

Posts: 394

Leon Curpa Stg1+


« Reply #8 on: November 25, 2011, 01:05:56 AM »

Using a boot mode tool. Not possible with NefMoto yet.
Logged
Gonzo
Sr. Member
****

Karma: +20/-30
Offline Offline

Posts: 483


« Reply #9 on: November 25, 2011, 02:10:25 PM »

I have the original file for this. I will upload when I can.
Logged
All_Euro
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 15


« Reply #10 on: November 25, 2011, 03:48:24 PM »

Awesome - greatly appreciated!
Logged
All_Euro
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 15


« Reply #11 on: November 28, 2011, 07:58:20 AM »

I have the original file for this. I will upload when I can.

Any luck finding this?
Logged
chiptuners
Newbie
*

Karma: +4/-1
Offline Offline

Posts: 17


« Reply #12 on: December 07, 2011, 09:31:49 AM »

i got one here you go
Logged
All_Euro
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 15


« Reply #13 on: December 07, 2011, 09:47:21 PM »

Thanks! I'll let you know how it goes once I figure out how to load it into ME7Logger & get rolling   Grin

chiptuners - I finally made time to try your file out today… I've only done one test log but it worked perfectly. Thanks again!!
« Last Edit: December 24, 2011, 02:11:45 PM by All_Euro » Logged
doublerwest
Full Member
***

Karma: +5/-4
Offline Offline

Posts: 178



« Reply #14 on: July 21, 2021, 10:40:57 AM »

i got one here you go
Hey guys Im a baby fish in this could you give me a tip on what software opens this file  .ori please...
Logged

W357
Pages: [1] 2
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.023 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)