Pages: [1]
Author Topic: Delete OBD Fault Code  (Read 7799 times)
mbkr89
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 96


« on: October 10, 2016, 08:15:49 AM »

I have Problem with my APY.
After install 400kpa map sensor and uninstall Maf, car got fault code 1662 (P0238) Maifold Pressure / Boost Sensor -->Signal too High.
I have log Voltage on sensor with multimeter and everthing is ok, go to 3.8 Volt.
Now I want kill the Fault code, ECU doesn't go to limp mode.
How to kill the Error Code ?
Logged
adam-
Hero Member
*****

Karma: +122/-33
Offline Offline

Posts: 2177


« Reply #1 on: October 10, 2016, 10:08:52 AM »

Why have you installed a different MAP sensor?
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #2 on: October 10, 2016, 10:39:34 AM »

are you running the 5120 hack? If not, changing the map sensor isn't going to do anything but cause problems.
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
mbkr89
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 96


« Reply #3 on: October 10, 2016, 10:50:46 AM »

i would drive mafless with 2,7 bar boost and the ecu have to know the correct boost.
Logged
adam-
Hero Member
*****

Karma: +122/-33
Offline Offline

Posts: 2177


« Reply #4 on: October 10, 2016, 02:13:48 PM »

It doesn't work like that I'm afraid.
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #5 on: October 10, 2016, 02:20:04 PM »

i would drive mafless with 2,7 bar boost and the ecu have to know the correct boost.

Maximum in the ECU is 2550mBar. No matter what sensor you choose, it can never understand any higher boost.

Please reread the wiki and all of the various 5120 mbar threads.

Even worse, "mafless" makes no sense in ME7 since it has no in-manifold pressure sensor.
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
mbkr89
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 96


« Reply #6 on: October 11, 2016, 12:51:50 AM »

Thank You all. I had found a solution. Mafless was the only way because gtx pump a lot of air during spool up.
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #7 on: October 11, 2016, 01:01:24 AM »

Mafless was the only way because gtx pump a lot of air during spool up.

That makes even less sense than just about every one of your posts in this thread.
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
_nameless
Hero Member
*****

Karma: +320/-445
Offline Offline

Posts: 2654



« Reply #8 on: October 11, 2016, 03:23:32 AM »

Might as well delete the o2 sensors too
Logged

If you are in the market for a tune and would like the ease of downloading and flashing a dyno tested tune for a fair price check out https://instatune.sellfy.store/
TijnCU
Hero Member
*****

Karma: +60/-4
Offline Offline

Posts: 690


flying brick


« Reply #9 on: October 11, 2016, 04:27:32 AM »

sensors are soooo 2015 Grin
Logged

vwaudiguy
Hero Member
*****

Karma: +53/-37
Offline Offline

Posts: 2024



« Reply #10 on: October 11, 2016, 08:15:39 AM »

Might as well delete the o2 sensors too

MK3 Turbo C2 style!
Logged

"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #11 on: October 11, 2016, 10:15:12 AM »

Might as well delete the o2 sensors too

It is the only way, because the half shafts spin "too fast" on acceleration.
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
10101011
Full Member
***

Karma: +10/-13
Offline Offline

Posts: 161



WWW
« Reply #12 on: October 19, 2016, 01:45:32 PM »

I need to wash off the DUMB off after reading this post  Roll Eyes. My head hurts now . .... Undecided
Logged

Poor quality lingers long after the price is forgotten ....
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.025 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)