Pages: [1]
Author Topic: WMI nozzle size suggestions for the 2.7T  (Read 7004 times)
vwaudiguy
Hero Member
*****

Karma: +53/-37
Offline Offline

Posts: 2024



« on: October 08, 2016, 10:29:41 AM »

I'm going to be installing 3-4 systems on 2.7t's this upcoming month. One will be stock (reflashed), 2 will be using Tial 605's (28 psi), and one with I think 770's. Looking for some real world system nozzle sizes (in cc if possible) for these different setups. We will be using Aquamist kits. The calculators I've seen suggest different numbers, so I figured I'd ask what people are using, and had success with. Thanks, guys.
Logged

"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
Dave9n3
Sr. Member
****

Karma: +26/-0
Offline Offline

Posts: 284


« Reply #1 on: October 25, 2016, 04:45:36 AM »

Had hoped someone would have replied to this by now lol. I don't know much so hopefully this reply isn't going to be useless to you but I was under the impression you wanted about 10-20% water methanol injected of the overall injector flow in cc/min for all cylinders so. for mine i run 317cc injectors x 4 cylinders = 1268cc/min then 10% of that is obviously 126.8cc/min and 20% would be 253.6cc/min. I then selected a nozzle of 250cc/min @100 psi from devilsown.

I cant remember where I found that information but I'll do some digging when I'm home from work to try and find it. Sorry if that was totally useless lol,
Logged
Dave9n3
Sr. Member
****

Karma: +26/-0
Offline Offline

Posts: 284


« Reply #2 on: October 25, 2016, 10:19:11 AM »

http://howertonengineering.com/calculating-jetting/ found it. hopefully that is useful for you.
Logged
vwaudiguy
Hero Member
*****

Karma: +53/-37
Offline Offline

Posts: 2024



« Reply #3 on: October 26, 2016, 11:18:50 AM »

http://howertonengineering.com/calculating-jetting/ found it. hopefully that is useful for you.

Thanks, Dave.
Logged

"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
prj
Hero Member
*****

Karma: +903/-420
Offline Offline

Posts: 5787


« Reply #4 on: October 26, 2016, 12:25:35 PM »

Don't use calculator.

K03's - 360hp crank - dual 0.8mm
PJ K04's - 530hp crank - dual 0.9mm
600-620hp crank - dual 1.0mm
Anything over 700hp crank - dual 1.2mm
Logged

PM's will not be answered, so don't even try.
Log your car properly.
vwaudiguy
Hero Member
*****

Karma: +53/-37
Offline Offline

Posts: 2024



« Reply #5 on: October 26, 2016, 12:31:57 PM »

Don't use calculator.

K03's - 360hp crank - dual 0.8mm
PJ K04's - 530hp crank - dual 0.9mm
600-620hp crank - dual 1.0mm
Anything over 700hp crank - dual 1.2mm

Thanks. The info I was looking for.  Smiley
Logged

"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.015 seconds with 16 queries. (Pretty URLs adds 0s, 0q)