|
_nameless
|
 |
« Reply #900 on: April 19, 2022, 11:18:35 PM »
|
|
|
So 7 is updated 10 is in the process of being updated. Both run .exe apps from cmd . Just when I try to run these cli apps it just opens In a new cmd window and closes . Does the same on both 10 and 7 also I tried redownloading apps and same thing .
You're using CMD wrong. CD to the path you need, then run it.
 |
|
|
|
|
Logged
|
If you are in the market for a tune and would like the ease of downloading and flashing a dyno tested tune for a fair price check out https://instatune.sellfy.store/ |
|
|
vanitution
Newbie
Karma: +0/-0
 Offline
Posts: 1
|
|
« Reply #901 on: May 25, 2022, 11:43:23 AM »
|
|
|
Anyone have a new link to download an eeprom programmer that works with windows 10?
|
|
|
|
|
Logged
|
|
|
|
ChameleonD
Newbie
Karma: +0/-0
Offline
Posts: 1
|
|
« Reply #902 on: June 09, 2022, 02:53:26 PM »
|
|
|
Please help me further..
I don't know what this error is...
C:\ecu immo>me7rw --bootmode -wp2 immoOFF.bin
Ver: 1.31
Com Port: 2
Baud Rate: 10400
Opening COM2 ... OK
Starting Boot_mode ... uC identification response = 0xC5 (C167 derivatives) ...
OK
Sending Loader + MonitorCore ... MonitorCore successfully launched
Initializing registers ... FAIL. (error=0x01)
Closing COM2
Could you please tell how do you solve this problem? |
|
|
|
|
Logged
|
|
|
|
stuydub
Full Member
Karma: +24/-12
Offline
Posts: 227
|
|
« Reply #903 on: June 10, 2022, 11:05:21 PM »
|
|
|
Could you please tell how do you solve this problem?
change the options |
|
|
|
|
Logged
|
|
|
|
Alfista Veru
Newbie
Karma: +0/-0
Offline
Posts: 1
|
|
« Reply #904 on: June 23, 2022, 03:46:25 AM »
|
|
|
Hi does anyone know if the programme works on Bosch ECU ME763 AO (0261208969) Fiat Grande Punto 2009 with 1.4 16V Petrol engine (Starjet).
Thanks
|
|
|
|
|
Logged
|
|
|
|
Pyeah91
Newbie
Karma: +0/-0
Offline
Posts: 1
|
|
« Reply #905 on: July 15, 2022, 03:02:17 AM »
|
|
|
Hello,
i get Error 0x50101 with setting KKL-Cable in Com2 in OBD Mode and 10400 Baud.
When i changed the Baud Rate to 9600 i get 0x50001.
Windows 7 32 Bit
1.8t BFB ME7.5
What can i do?
Thanx
UPDATE:
I Choose the version 1.31 with same Com Port and 9600 Baud rate and a few attempts later it works. Sometimes it wont work so you must restart the PC and give the ECU some time without Power.
|
|
|
|
« Last Edit: July 21, 2022, 02:39:45 AM by Pyeah91 »
|
Logged
|
|
|
|
TeknoFi
Full Member
Karma: +1/-3
Offline
Posts: 83
|
|
« Reply #906 on: August 01, 2022, 07:43:26 PM »
|
|
|
You only need the 10k resistor if you are keeping the pin grounded all the time. If you remove the ground as soon as it's in bootstrap mode, then you don't need the resistor.
I get a flash erase error with mpps v18 for some reason almost every time if I keep the resistor in circuit. But if I do the job without resistor, or disconnect the connection with resistor shortly after booting ecu, the flash succeeds every time.  Well, maybe this is useful to someone. |
|
|
|
|
Logged
|
|
|
|
Rick81
Full Member
Karma: +0/-10
Offline
Posts: 75
|
|
« Reply #907 on: August 06, 2022, 01:53:46 AM »
|
|
|
Ive downloaded this tool and extracted it and nothing happens?
|
|
|
|
|
Logged
|
|
|
|
Vollmer
Full Member
Karma: +14/-255
Offline
Posts: 78
Professional Cat Herder
|
|
« Reply #908 on: August 07, 2022, 08:49:23 AM »
|
|
|
Looking to use this on an Audi 00 A8/01 S8 cluster swap.
Need to retain Original ODO and Immo
|
|
|
|
|
Logged
|
Volvo HALL of SHAME:
Guitar24t aka Robert Hilton
SparkyR aka Brandon Halme
Prometey1982 aka Artem Vasiliev
MAXX ECU - Brett Willet
VIDA Leach - David Leech
Useless Twats:
PRJ - Dmitri from Estonia
|
|
|
EuroXs4
Full Member
Karma: +15/-31
Offline
Posts: 209
|
|
« Reply #909 on: August 18, 2022, 08:12:04 PM »
|
|
|
Anyone have any idea why I can't read this ecu via obd on the bench??
c:\>me7eeprom --OBD -r -p5 95040.bin
ME7_EEPROM v1.40
COM: 5, Baud Rate: 10400
Opening COM5 ... OK
Initiating communication ... FAIL. (error=0x50501)
Closing COM5
I have confirmed the port is correct. I have changed the baudrate it didnt make a difference. I have both can and kline hooked up. ECU part number 4Z7907551AA. ME7.1.1 0261208538
Also note hexnet is talking to ecu without issues with same connection configuration on bench setup.
|
|
|
|
« Last Edit: August 18, 2022, 08:28:40 PM by EuroXs4 »
|
Logged
|
|
|
|
TeknoFi
Full Member
Karma: +1/-3
Offline
Posts: 83
|
|
« Reply #910 on: August 21, 2022, 03:54:42 PM »
|
|
|
Anyone have any idea why I can't read this ecu via obd on the bench??
c:\>me7eeprom --OBD -r -p5 95040.bin
ME7_EEPROM v1.40
COM: 5, Baud Rate: 10400
Opening COM5 ... OK
Initiating communication ... FAIL. (error=0x50501)
Closing COM5
I have confirmed the port is correct. I have changed the baudrate it didnt make a difference. I have both can and kline hooked up. ECU part number 4Z7907551AA. ME7.1.1 0261208538
Also note hexnet is talking to ecu without issues with same connection configuration on bench setup.
is your ecu in boot mode? connecting can-line is not necessary. |
|
|
|
|
Logged
|
|
|
|
siggi1
Newbie
Karma: +0/-0
Offline
Posts: 1
|
|
« Reply #911 on: March 22, 2023, 03:55:40 PM »
|
|
|
Thank you so so much! Reeding the eeprom of my me 7.1 with Version 1.31 worked flawlessly over OBD.
|
|
|
|
|
Logged
|
|
|
|
murfieus
Jr. Member
Karma: +1/-0
Offline
Posts: 48
|
|
« Reply #912 on: June 20, 2023, 02:56:48 AM »
|
|
|
hi all , i got a me7.1.1 022906032GE 5871 but cant figure out wich eeprom size i need to select. there is no infomation about this ecu around.
i tryed to read and write with the 95040 but fails varify after writing. code on the eeprom 5P08C3. i tryed 95p08 but says the size is not correct.
Read in 512bytes
Bin starts 30 30 30 30 30 - is this a 1024kb R32 bin?
EEPROM Status:
- Type: ECU_eeprom
- Version: Immo3
- VIN: TRUZZZ8N051006793 (Audi Hungary 2005 - TT 99-06, Gyor, Hungary)
- SKC: 06641
- Immobiliser: On
- Checksum: OK
- Size: 512bytes
- Cluster Code: 14 22 3C 5A 80 97 B9
- P0601 DTC: not set
- Immo ID: AUZ5Z0D5236079
- Softcoding ID: 0133
- Tuner Tag:
- Flash Programming (successful): 0
- Flash Programming (attempts): 0
|
|
|
|
|
Logged
|
|
|
|
elektronik13
Full Member
Karma: +10/-32
Offline
Posts: 200
|
|
« Reply #913 on: June 24, 2023, 02:20:05 PM »
|
|
|
hi all , i got a me7.1.1 022906032GE 5871 but cant figure out wich eeprom size i need to select. there is no infomation about this ecu around.
i tryed to read and write with the 95040 but fails varify after writing. code on the eeprom 5P08C3. i tryed 95p08 but says the size is not correct.
Read in 512bytes
Bin starts 30 30 30 30 30 - is this a 1024kb R32 bin?
EEPROM Status:
- Type: ECU_eeprom
- Version: Immo3
- VIN: TRUZZZ8N051006793 (Audi Hungary 2005 - TT 99-06, Gyor, Hungary)
- SKC: 06641
- Immobiliser: On
- Checksum: OK
- Size: 512bytes
- Cluster Code: 14 22 3C 5A 80 97 B9
- P0601 DTC: not set
- Immo ID: AUZ5Z0D5236079
- Softcoding ID: 0133
- Tuner Tag:
- Flash Programming (successful): 0
- Flash Programming (attempts): 0
first you need to read the eeprom as 95p08 and then you will be able to write it the reading of this eeprom is incomplete |
|
|
|
« Last Edit: June 24, 2023, 02:32:53 PM by elektronik13 »
|
Logged
|
|
|
|
murfieus
Jr. Member
Karma: +1/-0
Offline
Posts: 48
|
|
« Reply #914 on: June 27, 2023, 11:07:50 AM »
|
|
|
first you need to read the eeprom as 95p08 and then you will be able to write it
the reading of this eeprom is incomplete
Thnks for reply, i did read it with the p08 but when i check it in cmd/eeprom is says check the file size (512kb?) , i made immo off and did the chks but still show fails after writing. When i check it with the “on screen” button he did write the changes |
|
|
|
|
Logged
|
|
|
|
|
