Pages: 1 ... 52 53 [54]
Author Topic: ME7 EEPROM programmer  (Read 441160 times)
SQT
Full Member
***

Karma: +2/-4
Offline Offline

Posts: 56


Respectfully SQT ;)


« Reply #795 on: August 12, 2019, 06:29:27 AM »

Has anyone been able to read the eeprom of a Touareg ecu (especially a 4D0 907 560 DB)?  I've used both 1.31 and 1.4 and can't get it to read, either via OBD or bootmode.  I've done this tons of time on 518 and 551 ECU's, previously...  Soon as it gets to Starting Boot_mode it errs with 0x09 and then hangs the command prompt, requiring a reboot.
Use only 1.4 version, chip 95P08, please share the file, in my opinion I have not the original firmware file
« Last Edit: August 12, 2019, 06:43:23 AM by SQT » Logged

a6 2.7
sorry for my English
Steve Bassen
Newbie
*

Karma: +2/-0
Offline Offline

Posts: 19


« Reply #796 on: August 15, 2019, 06:40:18 PM »

Use only 1.4 version, chip 95P08, please share the file, in my opinion I have not the original firmware file

When I get a chance this weekend I'll pull the ECU and try again, I'll post if it I'm successful with that setting.  Thanks!
Logged
bogdan wst
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4


« Reply #797 on: November 03, 2019, 10:07:53 AM »

Just want to say i can not conect to my car's ecu (audi a3 8L, 1.6 BFQ petrol engine- atached photo) in order to get the SKC so i could upgrade my half screen Magneti Marelli cluster to a VDO full DIS cluster. I only tried in OBD mode because i am not skilled in opening the ecu to put it in boot mode. I tried with genuine ross tech interface (VCP drivers installed, intelligent mode unckecked - unable to open COM PORT), INPA blue cable (initialising comunication error 21007), VAG Commander 3.6 cable (same error like with INPA cable). I tried connecting with the cluster connected and disconnected (the same result).
Can someone give me other suggestions?
Thank you.

Trimis de pe al meu SM-G950F folosind Tapatalk

Logged
macxxx
Sr. Member
****

Karma: +11/-0
Offline Offline

Posts: 304


« Reply #798 on: November 03, 2019, 01:39:55 PM »

As I remember Simos eeprom can be read only directly with a programeer
Logged
tunstyle
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 1


« Reply #799 on: December 22, 2019, 04:19:46 AM »

Hello
Is my first experience with this eeprom programmer, i need read 95080 eeprom for me7.3H4 Fiat.
I tried read this one with kkl 409.1 black cable and have error with "initializing registers fail". Any idea what to solve??
thanks all
Logged
bignslow
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 15


« Reply #800 on: December 28, 2019, 03:12:50 PM »

I am trying to read Volvo ME 7.1 EEPROM with 5P0C83 chip. No matter what options I chose I keep getting the same result. It goes through then a blank 1kb file. Any ideas?

Quote
ME7EEPROM" --bootmode 95040 --CSpin P8.2 -p 1 -b 10400 -r SavedROM.bin
ME7_EEPROM v1.40
COM: 1, Baud Rate: 10400
Memory type: 95040, size: 512
Chip Select pin: P8.2
Opening COM1 ... OK
Starting Boot_mode ... uC ID response 0xC5: C167CR ... OK
Sending Loader + MonitorCore ... MonitorCore successfully launched
Initializing registers ... OK
Sending EEPROM driver ... OK
Configuring SPI Interface ... OK
Checking EEPROM Status Register ... 0x00FF
Reading EEPROM ... OK
File saved
Closing COM1
Logged
Pages: 1 ... 52 53 [54]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.019 seconds with 18 queries. (Pretty URLs adds 0s, 0q)