ME7 EEPROM programmer

Pages: 1 ... 18 19 [20] 21 22 ... 63

« previous next »

Author

Topic: ME7 EEPROM programmer (Read 920799 times)

esilviu

Newbie

Karma: +1/-0
Offline

Offline

Posts: 22

	Re: ME7_95040 - EEPROM programmer « Reply #285 on: April 26, 2013, 09:50:23 PM »

I'm on my way to where the car is parked , trying the EEPROM reading after connecting the spare ECU in place of my original one.
I'll post the results.
Thanks for the info.


	Logged

esilviu

Newbie

Karma: +1/-0
Offline

Offline

Posts: 22

	Re: ME7_95040 - EEPROM programmer « Reply #286 on: April 27, 2013, 08:57:46 AM »

I Just read my spare ECU's EEPROM 95040 through OBD . IT worked like a charm and it took only 1.5 minutes, I want to mention that the ECU was not paired and it was read with ArgDub's tool after it was connected to the car without removing the cluster's fuse. After that with DDillenger -how to guide- I learned the SKC of the spare ECU and paired with my car cluster using VagCom. Everything went from the first time and all the procedure with the car running at the end with the spare ECU took less than 10 mins.
I thank you everybody , this is an awesome SITE.
Next that I have a spare working ECU is to write a new map in order to accomodate my supercharger to my NA engine without having DTC's and sustain a good fueling
Thanks ones again everybody for their input.


	Logged

allen123

Newbie

Karma: +0/-0
Offline

Offline

Posts: 3

	Re: ME7_95040 - EEPROM programmer « Reply #287 on: May 18, 2013, 12:49:28 PM »

Okay guys, I can't figure out why this doesn't work. I've tried everthing.

I have 4 different cables, 1 Ross-Tech old-school HEX-COM interface. 3 different variants of blue and black vag-tacho-like interfaces.
The one I'm trying now is a blue one with a FT232RL chip.

Set up using COM 1, baud rate set to 115200 in Windows XP sp3 under VirtualBox.

I always get error 0x50001 without seeing any communication with the ECU.

The Ross-Tech cable communicates effortly via a prolific usb-serial adapter in this setup.

ANY pointers would be appreaciated!

Oh, the car in question is a 2003 Audi A4 1.8T engine code BFB (think european AMB).

Cheers!


	Logged

dream3R

Hero Member

Karma: +18/-8
Offline

Offline

Posts: 1194

	Re: ME7_95040 - EEPROM programmer « Reply #288 on: May 22, 2013, 05:59:37 AM »

Hello and thank you for the great tool.

I'm trying to get this to work bootmode on a 2005> Volvo ME7 ECU with 95080 flash chip.

I get the following:

Starting Boot_mode ... uC identification response = 0xD5. Not supported. (error=0x01)

Are there any other avenue that I can explore or am I stuck desoldering etc?

Many thanks..


	Logged

How to work out values from an A2L

http://nefariousmotorsports.com/forum/index.php?topic=5525.msg52371#msg52371

Starting Rev's http://nefariousmotorsports.com/forum/index.php?topic=5397.msg51169#msg51169

noobs read this before asking http://nefariousmotorsports.com/forum/index.php?topic=9014.0title=

ORGORIGINAL 05 5120 creator for Volvo
ORIGINAL Datalogger (Freeware) Author
ORGINAL finder of the 'extra' torque' limits
I don't have ME7.01 A2L I just use ID

krazydbiker

Full Member

Karma: +4/-1
Offline

Offline

Posts: 202

	Re: ME7_95040 - EEPROM programmer « Reply #289 on: May 22, 2013, 06:12:38 AM »

same error i get dreamR, it doesnt do this with older 99 me7 from volvo's Undecided


	Logged

dream3R

Hero Member

Karma: +18/-8
Offline

Offline

Posts: 1194

	Re: ME7_95040 - EEPROM programmer « Reply #290 on: May 22, 2013, 09:17:17 AM »

Quote from: krazydbiker on May 22, 2013, 06:12:38 AM

same error i get dreamR, it doesnt do this with older 99 me7 from volvo's Undecided

Got it to read 100%! I assume writing will work but haven't tried.

Thanks to a friend who helped (rkam).

The bin file was a 1:1 match from the read I took with my chip programmer off-board.

Here is the console output if it helps anyone:

Quote

ME7EEPROM.exe -p 1 --bootmode 95080 -r --CSpin P8.2 dump2.bin
ME7_EEPROM v1.40
COM: 1, Baud Rate: 10400
Memory type: 95080, size: 1024
Chip Select pin: P8.2
Opening COM1 ... OK
Starting Boot_mode ... uC ID response 0xD5 ... OK
Sending Loader + MonitorCore ... MonitorCore successfully launched
Reading IDCHIP ... 0x0C44: C167CS ... OK
Initializing registers ... OK
Sending EEPROM driver ... OK
Configuring SPI Interface ... OK
Checking EEPROM Status Register ... 0x0080
Reading EEPROM ... OK
File saved
Closing COM1


	Logged

How to work out values from an A2L

krazydbiker

Full Member

Karma: +4/-1
Offline

Offline

Posts: 202

	Re: ME7_95040 - EEPROM programmer « Reply #291 on: May 22, 2013, 10:12:10 AM »

mind sharing how you got it to work :-D i went the old school method with mine, worked though, ofcourse i dont plan on frying my ecu again

edit : nvm, i read your commandline, thanks


	Logged

dirtygerman

Newbie

Karma: +0/-0
Offline

Offline

Posts: 5

	Re: ME7_95040 - EEPROM programmer « Reply #292 on: May 22, 2013, 06:40:59 PM »

noob question Embarrassed

but has anyone delt with error message boot_mode fail no echo from cable error=0x07? I am jumping pin 24 to ground via a switch I soldered from pin24 to the outer section of the PCB and if so what might be causing this issue? I have successfully read this ecu with my current cable and I am currently using version 1.31


	Logged

dream3R

Hero Member

Karma: +18/-8
Offline

Offline

Posts: 1194

	Re: ME7_95040 - EEPROM programmer « Reply #293 on: May 23, 2013, 02:44:19 AM »

Quote from: dirtygerman on May 22, 2013, 06:40:59 PM

noob question Embarrassed

I had this when I first used it yesterday, I updated the FTDI drivers from the site and set the cable to COM1 instead of 10 then rechecked my connections and it worked.

Not sure which one of those fixed it to be truthful.


	Logged

How to work out values from an A2L

dream3R

Hero Member

Karma: +18/-8
Offline

Offline

Posts: 1194

	Re: ME7_95040 - EEPROM programmer « Reply #294 on: May 29, 2013, 12:11:22 PM »

Hi there,

I've got issues writing to my 95080, I can read fine which makes me think it's some sort of write protection?

Quote

ME7EEPROM.exe -p 1 --bootmode 95080 -w --CSpin P8.2 dream3rimmo.bin
ME7_EEPROM v1.40
COM: 1, Baud Rate: 10400
Memory type: 95080, size: 1024
Chip Select pin: P8.2
Opening COM1 ... OK
Starting Boot_mode ... uC ID response 0xD5 ... OK
Sending Loader + MonitorCore ... MonitorCore successfully launched
Reading IDCHIP ... 0x0C44: C167CS ... OK
Initializing registers ... OK
Sending EEPROM driver ... OK
Configuring SPI Interface ... OK
Checking EEPROM Status Register ... 0x0080
Writing EEPROM ................................................................
OK
Verifying EEPROM write ... FAIL. (error=0x70101)
Closing COM1


	Logged

How to work out values from an A2L

MyTunes

Full Member

Karma: +9/-5
Offline

Offline

Posts: 83

	Re: ME7_95040 - EEPROM programmer « Reply #295 on: May 30, 2013, 09:59:49 AM »

Quote from: dream3R on May 22, 2013, 09:17:17 AM

When I use your exact same argument except I use 95P08 instead of 95080 and P6.3 instead of P8.2 I get: error: too many arguments specified...

If I use bootmode to try to read without the CSpin and P6.3 I get:
Starting Boot_mode... uC ID response 0X00. Unknown ID. (error=0x40201)
My chip is 95P08C3

If I try to do a bootmode write I get an error of: Invalid file size 'file.bin'. (error=0x3010C)

This in an a ME7.1.1 from a D3A8 and again the eeprom chip is 95P08C3
Here is a sample read I got from using a couple of various tools...
Any ideas Argdub?
And thank you for this wonderful tool


	Logged

dream3R

Hero Member

Karma: +18/-8
Offline

Offline

Posts: 1194

	Re: ME7_95040 - EEPROM programmer « Reply #296 on: May 30, 2013, 10:08:32 AM »

Which version are you using it HAS to be 1.4


	Logged

How to work out values from an A2L

MyTunes

Full Member

Karma: +9/-5
Offline

Offline

Posts: 83

	Re: ME7_95040 - EEPROM programmer « Reply #297 on: May 30, 2013, 11:51:22 AM »

Quote from: dream3R on May 30, 2013, 10:08:32 AM

Which version are you using it HAS to be 1.4

Yes I am using 1.40 from page 12 I think it was


	Logged

MyTunes

Full Member

Karma: +9/-5
Offline

Offline

Posts: 83

	Re: ME7_95040 - EEPROM programmer « Reply #298 on: June 03, 2013, 06:36:44 AM »

Hmm I just noticed something odd that may explain the write error.
On my computer the file shows as 1kb so I didn't think anything of it, but I just noticed that when I uploaded it to here it shows as 512. I took a pic of the chip on the board and it is indeed the 5P08C3.
Now i'm corn fused...


	Logged

EuroDriven

Newbie

Karma: +0/-0
Offline

Offline

Posts: 4

	Re: ME7_95040 - EEPROM programmer « Reply #299 on: June 06, 2013, 07:43:29 AM »

Quote from: masterj on June 03, 2012, 04:50:59 AM

understood

Now please look at attached image and tell me if I am correct

So I am just trying to understand the checksum calculations. I know there is a utility to do it, but I want to know exactly how it works.

I understand 0xFFFF - (Sum of Octets) but that seems over simplified.

It looks like it is actually 0xFFFF - (Sum of Octets) - (row offset from 0x10)

The above is where 0x10 counts as the 0th row. This mostly makes sense to me but why is row 0x10 and 0x20 the same with a checksum offset by 1, but then rows 0x90 and 0xA0 are the same values as well but the checksums are exactly the same? Same thing with rows 0x70 and 0x80.


	Logged

Pages: 1 ... 18 19 [20] 21 22 ... 63

« previous next »

Jump to:

Navigation

Personal Tools

November 22, 2024, 05:18:42 PM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search