NefMoto > Technical > Flashing and Chipping > edc17cp14 2500rpm limit
Pages: [1]
« previous next »
Author Topic: edc17cp14 2500rpm limit  (Read 5732 times)
Sadas
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 2
« on: December 04, 2016, 03:19:03 PM »
Hi all,

I need to disable 2500rpm limit, which comes on the dash after some spirited driving. This limit comes with faults:

Oil Pressure Regulating Valve P164E - 001 - Electrical Malfunction
Oil Pressure Switch P164B - 001 - Malfunction - Intermittent

I've disabled those faults by changing fault class to 0. Those no longer show on ECU, but the limit still kicks in.

Any ideas how to get rid of it?
Logged
vwaudiguy
Hero Member
*****

Karma: +53/-37
Offline Offline

Posts: 2024
« Reply #1 on: December 04, 2016, 03:45:52 PM »
I guess I'll be the first to ask. What's up with your oil pressure/ warning system?
Logged
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
prj
Hero Member
*****

Karma: +915/-427
Offline Offline

Posts: 5839
« Reply #2 on: December 04, 2016, 11:45:04 PM »
Switch off the diagnosis not the fault display, but yeah - why are you trying to disable these?

Have you measured actual oil pressure? These faults come up together when the oil pressure is low at high RPM.
Logged
PM's will not be answered, so don't even try.
Log your car properly.
turbojohan
Full Member
***

Karma: +5/-0
Offline Offline

Posts: 185
« Reply #3 on: December 05, 2016, 07:48:50 AM »
Put fehlerklasse to 0 won't change anything accept from dtc Not sent to dtclist and MIL. You need to turn limp off from this dtc with abschaltmaske.


Verzonden vanaf mijn iPhone met Tapatalk
Logged
Sadas
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 2
« Reply #4 on: December 05, 2016, 04:51:56 PM »
the new engine is slightly different, and has no oil pressure regulator. So I need to adapt software and disable the diagnosis to prevent limp mode.

Quote from: turbojohan on December 05, 2016, 07:48:50 AM
Put fehlerklasse to 0 won't change anything accept from dtc Not sent to dtclist and MIL. You need to turn limp off from this dtc with abschaltmaske.
Turbojohan, I tried to change abschaltmaske from 00FF to 0000, but that did not help. Am I doing it wrong?
Logged
turbojohan
Full Member
***

Karma: +5/-0
Offline Offline

Posts: 185
« Reply #5 on: December 06, 2016, 01:04:59 AM »
yes you do it wrong.
Look how it works and try again ;-)
Logged
prj
Hero Member
*****

Karma: +915/-427
Offline Offline

Posts: 5839
« Reply #6 on: December 06, 2016, 01:30:58 AM »
You need to set the MSB (bit, not byte) of the Abschaltmaske to always disable.
Logged
PM's will not be answered, so don't even try.
Log your car properly.
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • April 22, 2024, 10:29:55 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.028 seconds with 16 queries. (Pretty URLs adds 0.005s, 0q)