Pages: [1]
Author Topic: Rpm per mph calculation  (Read 6095 times)
6L20vt
Full Member
***

Karma: +2/-0
Offline Offline

Posts: 152


« on: December 09, 2016, 02:00:47 PM »

Hello, what is the formula to calculate correct rpm/mph for ecuxplot?
I have info about my gearbox but i dont know calculate the correct number for my car in this units here is the info:

1ª   9,1
2ª   15,4   
3ª   22,0   
4ª   28,9   
5ª   36,6   
R   9,8

Kph x 1000rpm. I make my logs in 4° gear usually. Can help me?. Regards
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #1 on: December 09, 2016, 02:13:55 PM »

Get a GPS receiver or just use your phone and a GPS app.
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
6L20vt
Full Member
***

Karma: +2/-0
Offline Offline

Posts: 152


« Reply #2 on: December 09, 2016, 02:21:49 PM »

I have torque app and obd elm can i make anything with it?What should I measure on my GPS? For example I keep the rpm to 2000 in fourth gear and see how many mph I get? And then divide them by 1000?. Regards
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #3 on: December 09, 2016, 04:37:33 PM »

No. Just divide rpm by mph.
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
6L20vt
Full Member
***

Karma: +2/-0
Offline Offline

Posts: 152


« Reply #4 on: December 10, 2016, 04:46:28 PM »

Hello again, I have done what you told me, but I have a doubt, if I do that dovision let's say 4000, it does not give me the same result as if I do the division with the mph I get 5000 for example. What am I doing wrong? Sorry to ask so much but I would like to have well configured ecuxplot. Thank you
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #5 on: December 10, 2016, 04:52:10 PM »

rpm/mph should be constant for a given gear.

I have no idea what you're asking.

How is "4000" a "division"?
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
TijnCU
Hero Member
*****

Karma: +60/-4
Offline Offline

Posts: 690


flying brick


« Reply #6 on: December 11, 2016, 05:01:21 AM »

Gears are liniar.
Step 1. Drive at 3000rpm
Step 2. Check gps for actual speed (in mph)
Step 3. Divide 3000 by your actual speed.
Result is your rpm per mph in that specific gear.
Logged

6L20vt
Full Member
***

Karma: +2/-0
Offline Offline

Posts: 152


« Reply #7 on: December 11, 2016, 01:33:47 PM »

Ok, solved, it was a failure in my measurements, thank you very much for your clarifications. a greeting
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.015 seconds with 16 queries. (Pretty URLs adds 0s, 0q)