Pages: [1]
Author Topic: S4 4.2 8E0910560H SAI, EVAP and CAT delete with Readiness  (Read 3943 times)
chain_slappinS4
Full Member
***

Karma: +11/-9
Offline Offline

Posts: 58


« on: December 27, 2016, 10:33:27 AM »

thought i would share my settings for the 8E0910560H ecu for sai, evap and cat delete

address and id are as follows:

181A1 CDKAT = 0
181A5 CDLASH = 0
181A6 CDLDP = 0
181AA CDLSHV = 0
181B0 CDSLS = 0
181B3 CDTES = 0
181BA CWKONABG =0 --- no sai and no cat installed
19994 FKHABMN = 0

i left MSLUB (1B48C) alone, and when i checked readiness in VCDS everything showed as passed.

i have all 4 O2 sensors plugged in, and SAI pump and valves removed, vac. line capped. for some reason i did not need to disable circuit diagnotics in ESKONF ( not sure why, but i need to read up on it some more, and when i figure out why, i'll update this post).

i've been running this way for about 2 1/2 - 3 weeks ( 270 or so miles ) and no check engine light, and DTC's.... yet..

hope this helps.....

Mark
Logged

microsoft asked me to install windows nt or better, so i installed Solaris!!
metronet
Full Member
***

Karma: +5/-0
Offline Offline

Posts: 73



« Reply #1 on: December 27, 2016, 12:35:06 PM »

Not sure if it's the same for the S4 4.2 but for the N/A 3.0 ME7.1.1 I had to do a modification in assembly code in order for the front two O2 sensors to "check" and PASS.

I believe if you set CDLSV=0 (Bit B_cdlsv) than it doesn't "check" and will always show PASS.

>> http://nefariousmotorsports.com/forum/index.php?topic=8764.msg90946#msg90946

On another note, I haven't done anything yet for CDLDP. I do however see part# listed in ETKA for countries that do not require Leak Detection Pump with a plug at the throttle body: 034133335D Would be interesting to see if anyone has done LDP delete but still keep EVAP N80 Smiley

Logged
mister t
Sr. Member
****

Karma: +74/-18
Offline Offline

Posts: 343


« Reply #2 on: January 05, 2017, 08:08:43 PM »

Awesome, thanks for the info  Smiley
Logged
SoerenDa
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4


« Reply #3 on: August 28, 2022, 10:09:40 PM »


181BA CWKONABG =0 --- no sai and no cat installed
19994 FKHABMN = 0



Good morning Guys!

I know this thread is pretty old and outdated, but let me share my thoughts.
Im pretty much a beginner, but from my understanding it should be irrelevant to set FKHABMN = 0, because the FR states that bit#1 in CWKONABG already sets B_kath=0, which in return should mean that FKHABMN = 0 isn't nessesary, am I right?

Please correct me if I'm wrong, as this is more of a question Smiley

Cheers,
Soeren
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.015 seconds with 18 queries. (Pretty URLs adds 0s, 0q)