Pages: [1]
Author Topic: ME7.1.1 ECM and Flashing Equipment!  (Read 11523 times)
CoupedUp
Full Member
***

Karma: +0/-0
Offline Offline

Posts: 59


« on: September 07, 2016, 04:10:33 PM »

I recently sold my last and only VAG car so I don't have a need for any of this stuff since I'm not an Electrical Engineer. All prices are OBO.

The ECU is a 4Z7907551R with a Stock BIN(I believe) only used it to start the car(2003 A6 2.7T) before this listing. It is missing all 4 screws on the back side but the adhesive is very much intact. Price: $100 shipped.



All of below: Price: $95 shipped



The PSU has been modified with switch for easy start/kill and all 12V and ground rails trimmed and made accessible from the outside. Also, soldered to this is a setup for an ME7.1.1 bench flash(ECU pigtail, OBD-II connector, etc). I had planned on putting wire wrap on it after solidifying it was all correct but never got to it. Price: $25

Galletto Cable and Dumb Blue Cable - Price: $20 shipped



USB PIC Programmer with 8-Pin Ponoma SOIC Clip - Price: $50

Logged
Ephry
Newbie
*

Karma: +1/-0
Offline Offline

Posts: 16


« Reply #1 on: September 22, 2016, 07:51:30 PM »

Any of this available still?

E

I recently sold my last and only VAG car so I don't have a need for any of this stuff since I'm not an Electrical Engineer. All prices are OBO.

The ECU is a 4Z7907551R with a Stock BIN(I believe) only used it to start the car(2003 A6 2.7T) before this listing. It is missing all 4 screws on the back side but the adhesive is very much intact. Price: $100 shipped.



All of below: Price: $95 shipped



The PSU has been modified with switch for easy start/kill and all 12V and ground rails trimmed and made accessible from the outside. Also, soldered to this is a setup for an ME7.1.1 bench flash(ECU pigtail, OBD-II connector, etc). I had planned on putting wire wrap on it after solidifying it was all correct but never got to it. Price: $25

Galletto Cable and Dumb Blue Cable - Price: $20 shipped



USB PIC Programmer with 8-Pin Ponoma SOIC Clip - Price: $50


Logged
Ephry
Newbie
*

Karma: +1/-0
Offline Offline

Posts: 16


« Reply #2 on: October 02, 2016, 09:19:45 AM »

Sent PM


Sent from my iPhone using Tapatalk
Logged
Tricky0
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 8


« Reply #3 on: February 21, 2017, 05:49:28 AM »

Pm sent

Sent from my SM-G935U using Tapatalk
Logged
vw4life
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 8


« Reply #4 on: May 13, 2017, 03:24:54 AM »

Hello, could u/would u duplicate that set up?
I'll pay u up front, I have the galletto 1260 interface /cables.
K line, lmk thank u.

Sent from my SM-G900V using Tapatalk
Logged
CoupedUp
Full Member
***

Karma: +0/-0
Offline Offline

Posts: 59


« Reply #5 on: May 21, 2017, 05:07:38 PM »

Hello, could u/would u duplicate that set up?
I'll pay u up front, I have the galletto 1260 interface /cables.
K line, lmk thank u.

Sent from my SM-G900V using Tapatalk

Are you just wanting the PSU with ME7.1.1 and OBD-II connectors? Also, it is much easier to reach me by email: seandeanc at gmail...
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.016 seconds with 18 queries. (Pretty URLs adds 0s, 0q)