Pages: [1]
Author Topic: dump firmware from haldex gen4 controller  (Read 7733 times)
k0mpresd
Hero Member
*****

Karma: +146/-54
Offline Offline

Posts: 1655


« on: April 12, 2017, 11:19:13 PM »

p0l.4 and tx/rx found in zip file.
also connect rstin to 5v via switch.

Quote
_connect
_clearselections
_addselection 00000,4ffff
_upload
_save test.hex

read the datasheet.  Wink

http://www109.zippyshare.com/v/jUebJZbj/file.html
Logged
aef
Hero Member
*****

Karma: +69/-46
Offline Offline

Posts: 1566


« Reply #1 on: April 12, 2017, 11:31:18 PM »

Smiley

Hat's off to you!
Logged
vwaudiguy
Hero Member
*****

Karma: +53/-37
Offline Offline

Posts: 2024



« Reply #2 on: April 12, 2017, 11:34:18 PM »

Yugo boi
Logged

"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
k0mpresd
Hero Member
*****

Karma: +146/-54
Offline Offline

Posts: 1655


« Reply #3 on: April 13, 2017, 12:12:11 PM »

do not even know why i bother posting. we are too busy worried how we can steal vcds cables and too lazy to actually use an application for all its functionality.

but maybe there is still hope.

write controller:
 
Initializing ST10Flasher.dll
Init COM1 at 9600 bauds
 
*LOAD MONITOR-->OK
 
* ERASE BANKS -->OK
 
*LOAD HEXFILE:F:\WinOLS 0BR907554C 0_7FFF (Original) - .hex-->OK
 
*FILE INFO FOR FILE:WinOLS 0BR907554C 0_7FFF (Original) - .hex
Size = 32768 bytes.
Programming time = 35 s.
Block(s): 0, 1, 2, 3
 
*PROGRAM FLASH MEMORY -->OK
 
*LOAD HEXFILE:F:\WinOLS 0BR907554C  18000_4FFFF (Original) - .hex-->OK
 
*FILE INFO FOR FILE:WinOLS 0BR907554C  18000_4FFFF (Original) - .hex
Size = 229376 bytes.
Programming time = 239 s.
Block(s): 4, 5, 6, 7
 
*PROGRAM FLASH MEMORY -->OK
Logged
vwaudiguy
Hero Member
*****

Karma: +53/-37
Offline Offline

Posts: 2024



« Reply #4 on: April 13, 2017, 12:26:09 PM »

WAIT. We can steal VCDS cables?HuhHuhHuhHuh Where do I sign up??
Logged

"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
john9357
Full Member
***

Karma: +10/-1
Offline Offline

Posts: 54


« Reply #5 on: July 13, 2018, 05:14:14 AM »

k0mpresd, the link is dead. can you reupload? thanks
Logged
k0mpresd
Hero Member
*****

Karma: +146/-54
Offline Offline

Posts: 1655


« Reply #6 on: July 13, 2018, 07:17:23 AM »

k0mpresd, the link is dead. can you reupload? thanks

you can find p0l.4, tx, rx in the data sheet of the mcu. then the rest needed is posted in this thread.
Logged
john9357
Full Member
***

Karma: +10/-1
Offline Offline

Posts: 54


« Reply #7 on: July 13, 2018, 07:30:29 AM »

ahh i think it's dump! i have already the pin for bm. Its possible to post yout ori?
Logged
purepower
Newbie
*

Karma: +5/-1
Offline Offline

Posts: 22



« Reply #8 on: July 22, 2018, 07:31:20 AM »

Sorry guys.

First of all which tool are you using to read the Haldex Controller?

I can't catch this point.

Thank you
Logged

PurePowerPerformance
Danielsvamp
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 4

yo


« Reply #9 on: November 03, 2023, 04:05:12 AM »

^^^
+1
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.02 seconds with 17 queries. (Pretty URLs adds 0s, 0q)