tuningfreak
Newbie
Karma: +9/-5
 Offline
Posts: 18
|
 |
« Reply #225 on: July 27, 2020, 02:43:24 AM »
|
|
|
Hello guys, as you know dq500 and dq250mqb has boosted launch feature and some tuners can make this feature to the older dq250 versions. Here is the example video : https://youtu.be/jsUEcDTKf_4Is anyone have experience about it? which maps should we touch? Best Regards |
|
|
|
|
Logged
|
|
|
|
teobolo
Full Member
Karma: +24/-6
Offline
Posts: 112
|
|
« Reply #226 on: July 27, 2020, 05:02:54 AM »
|
|
|
mate did you look previous posts?or just post what you need for .
As i write on that topic almost none have manage to make it (only TVS )
|
|
|
|
|
Logged
|
|
|
|
|
birchbark506
|
|
« Reply #227 on: August 07, 2020, 07:42:11 PM »
|
|
|
KusLaunchNAbMax_ko
do you know what address that would be. my a2l dose not have that map |
|
|
|
|
Logged
|
|
|
|
mantasos
Newbie
Karma: +0/-1
Offline
Posts: 8
|
|
« Reply #228 on: September 30, 2020, 12:39:00 AM »
|
|
|
mate did you look previous posts?or just post what you need for .
As i write on that topic almost none have manage to make it (only TVS )
Haven't tried it but, i believe that you can implement hard launch control on ecu like you would for a manual but having break switch & full throttle instead of clutch switch. set to 200-300rpm lower than dsg launch control threshold. i mean, if im thinking right, it will never get to dsg lc rpm so it will never cut throttle and the engine's ecu hard launch control will be enabled  |
|
|
|
« Last Edit: September 30, 2020, 12:43:25 AM by mantasos »
|
Logged
|
|
|
|
|
FlyboyS4
|
|
« Reply #229 on: October 18, 2020, 06:28:02 PM »
|
|
|
Have any of you used HP Tuners software for tuning the DQ250? Some screen shots of the interface http://mygolfmk7.com/knowledgebase/hp-tuner-suite-screenshots/There's little guidance on the HP Tuners site and the software appears to be limited to providing brief descriptions of the variables. |
|
|
|
|
Logged
|
|
|
|
newai
Newbie
Karma: +0/-0
Offline
Posts: 2
|
|
« Reply #230 on: October 27, 2020, 09:58:48 PM »
|
|
|
Hi everyone! Please help enable launch control on DSG250.
|
|
|
|
|
Logged
|
|
|
|
|
gman86
|
|
« Reply #231 on: October 27, 2020, 11:46:26 PM »
|
|
|
Hi everyone! Please help enable launch control on DSG250.
Sure! How about we do your engine too? For completeness. |
|
|
|
|
Logged
|
|
|
|
newai
Newbie
Karma: +0/-0
Offline
Posts: 2
|
|
« Reply #232 on: October 28, 2020, 09:46:06 PM »
|
|
|
Sure! How about we do your engine too? For completeness.
Thanks, but I have 225 hp and 480 nm. And now the problem is in a good start. I deal with DSG myself with the help of this forum. But I can't figure out how to turn on the launch control. |
|
|
|
|
Logged
|
|
|
|
|
birchbark506
|
|
« Reply #233 on: January 23, 2021, 07:49:41 AM »
|
|
|
anyone got anything for the DQ250 MQB i been using the Exx full damos but there a few maps that seem to be missing for the MQB dq250
|
|
|
|
|
Logged
|
|
|
|
marchewa
Full Member
Karma: +4/-0
Offline
Posts: 53
|
|
« Reply #234 on: May 05, 2021, 03:03:13 AM »
|
|
|
DSG DQ250 reverse light signal
Old dq250 (eg. in audi tt 1gen) had direct reverse gear signal on pin 12 while newer gearboxes are not using this pin. I have newer DSG (02E300014H 069D61902ec__getriebe_DSG_chD6 F31S) and would like to ask if is it possible to activate this signal in software? I need it as this gearbox will be working in older chassis.
dsg readout attached
|
|
|
|
|
Logged
|
|
|
|
Leonhard
Full Member
Karma: +29/-2
Offline
Posts: 115
|
|
« Reply #235 on: May 05, 2021, 12:44:10 PM »
|
|
|
check this one:
3191B 1x1 8Bit
Id: SbeEnableRFL_ko
"Ausgabe Rückfahrlicht ein-/ausschalten"
|
|
|
|
|
Logged
|
|
|
|
marchewa
Full Member
Karma: +4/-0
Offline
Posts: 53
|
|
« Reply #236 on: May 07, 2021, 12:00:41 AM »
|
|
|
Thanks Leonhard, I set to 1 but it is not working and still constant +3V on pin 12.
|
|
|
|
|
Logged
|
|
|
|
Leonhard
Full Member
Karma: +29/-2
Offline
Posts: 115
|
|
« Reply #237 on: May 09, 2021, 03:48:42 AM »
|
|
|
Ok, too bad, but that's all I got  |
|
|
|
|
Logged
|
|
|
|
jochen_145
Full Member
Karma: +9/-4
Offline
Posts: 177
|
|
« Reply #238 on: May 09, 2021, 09:42:56 AM »
|
|
|
Thanks Leonhard, I set to 1 but it is not working and still constant +3V on pin 12.
Witch way did you check ? T20a/12 should be a low-side-switch AFAIR.. |
|
|
|
|
Logged
|
|
|
|
kepsus
Newbie
Karma: +0/-1
Offline
Posts: 7
|
|
« Reply #239 on: July 14, 2021, 11:53:11 AM »
|
|
|
Now my DQ250 is not in a vag car, but i still have med 9.1 ecu. Would it possible to code the dq250 to have launch , even that i dont have any ESP /ABS
|
|
|
|
|
Logged
|
|
|
|
|
