NefMoto > Noob Zone > Noob Guides and FAQs (Moderator: turboat) > LC/NLS
Pages: 1 ... 5 6 [7] 8 9 ... 21
« previous next »
Author Topic: LC/NLS  (Read 234427 times)
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12268


WWW
« Reply #90 on: September 03, 2019, 11:57:04 PM »
Quote from: jaremyhawk on September 03, 2019, 06:26:38 PM
^ thanks

now an update on the LC NLS issue... no lift shift is working confirmed this when some dodge cummins tried pulling on me (took it to gapplebees ) i believe its been set at 5500 interesting enough i think lc is semi working but is set at 6000 rpm? has anyone gotten this working on a vr6 12v? me7.1

Please read the whole thread from the start. There is a reason I merged your post. I have also updated post #3 since apparently bold and red is not obvious enough.
Logged
ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
Blazius
Hero Member
*****

Karma: +89/-40
Offline Offline

Posts: 1282
« Reply #91 on: September 04, 2019, 12:21:11 AM »
Quote from: jaremyhawk on September 03, 2019, 10:17:52 AM
to minimize wheel spin they both have the same function right?

No. LC is to build boost off the start line so you dont get boost lag, as that you would cost you important miliseconds or seconds for racecars. Antilag is basically the same only that its active while the car is rolling and your foot is off the accelerator to keep the turbine spinning.
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12268


WWW
« Reply #92 on: September 04, 2019, 12:23:33 AM »
Quote from: Blazius on September 04, 2019, 12:21:11 AM
No. LC is to build boost off the start line

The problem is that the term "LC" is used to mean many different things depending on context. You're wasting your time on a purely semantic argument.

In *THIS* thread, LC means both building boost and holding launch RPM right before launch, not traction control.
« Last Edit: September 04, 2019, 12:26:11 AM by nyet » Logged
ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
Blazius
Hero Member
*****

Karma: +89/-40
Offline Offline

Posts: 1282
« Reply #93 on: September 04, 2019, 12:38:11 AM »
Quote from: nyet on September 04, 2019, 12:23:33 AM
The problem is that the term "LC" is used to mean many different things depending on context. You're wasting your time on a purely semantic argument.

In *THIS* thread, LC means both building boost and holding launch RPM right before launch, not traction control.

Well yes people call TC and other things things like ALS launch control too. But LC must hold hold a spool RPM to retain the boost too, so by definition you are at a "launch" RPM, RPM holding "launch control" without ignition retard in my books is called soft launch control.

But yes its a waste time to argue about stupid stuff like this. The only reason you'd want launch control in an NA car is to impress your friends thats all IMO.
Logged
LuckkyLuke
Newbie
*

Karma: +2/-21
Offline Offline

Posts: 16
« Reply #94 on: October 23, 2019, 01:21:10 PM »
Hi, Can you help me, please? I need LC +ALS for the ECU, VW Jetta VR6 ME7.1.1

I am tested, but not start car. Checksum is OK.


Thank you very much.
Logged
ZakDodge
Jr. Member
**

Karma: +2/-0
Offline Offline

Posts: 42
« Reply #95 on: October 23, 2019, 01:32:07 PM »
Post the original file please
Logged
LuckkyLuke
Newbie
*

Karma: +2/-21
Offline Offline

Posts: 16
« Reply #96 on: October 23, 2019, 01:44:11 PM »
Quote from: ZakDodge on October 23, 2019, 01:32:07 PM
Post the original file please

The original file is attached.
Logged
Kompiesto
Full Member
***

Karma: +4/-5
Offline Offline

Posts: 109
« Reply #97 on: October 24, 2019, 02:30:55 AM »
if is ST10 ecu You need do ASM mods.
Logged
LuckkyLuke
Newbie
*

Karma: +2/-21
Offline Offline

Posts: 16
« Reply #98 on: October 24, 2019, 02:53:05 AM »
Quote from: Kompiesto on October 24, 2019, 02:30:55 AM
if is ST10 ecu You need do ASM mods.

What is ASM mods. Where can I find a description?

Thank you very much.
Logged
adam-
Hero Member
*****

Karma: +123/-33
Offline Offline

Posts: 2179
« Reply #99 on: October 24, 2019, 04:52:26 AM »
Quote from: LuckkyLuke on October 24, 2019, 02:53:05 AM
What is ASM mods. Where can I find a description?

Yeaaaahhh, with that question, you're gonna be up shit creek with no paddle.
Logged
_nameless
Hero Member
*****

Karma: +342/-466
Offline Offline

Posts: 2800
« Reply #100 on: October 24, 2019, 05:00:29 AM »
this is not st10 fwiw
Logged
Giving your mom a tuneup
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12268


WWW
« Reply #101 on: October 24, 2019, 09:04:48 AM »
Merged with master "I ABSOLUTELY HAVE TO HAVE LC" noob thread
Logged
ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
LuckkyLuke
Newbie
*

Karma: +2/-21
Offline Offline

Posts: 16
« Reply #102 on: October 24, 2019, 01:07:40 PM »
Probably nobody will help.

:-)
Logged
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425
« Reply #103 on: November 12, 2019, 01:28:01 AM »
At many places it have warning that LC/NLS will burn coil pack, or output in ECU...
LC/NLS sets  tsrldyn = 0, what schould be dwell time set to zero. Acording to that when tsrldyn is set to 0, there schould not be output voltage from ECU to charge coils. So how that can burn anything?
Logged
gt-innovation
Sr. Member
****

Karma: +60/-91
Offline Offline

Posts: 449
« Reply #104 on: November 12, 2019, 07:41:08 AM »
Quote from: BlackT on November 12, 2019, 01:28:01 AM
At many places it have warning that LC/NLS will burn coil pack, or output in ECU...
LC/NLS sets  tsrldyn = 0, what schould be dwell time set to zero. Acording to that when tsrldyn is set to 0, there schould not be output voltage from ECU to charge coils. So how that can burn anything?

That is only specific to the code that floats around here and only for old coilpacks and 29f400 ecus...

There are many ways to build boost and make a proper lc with 0 impact on the engine reliability... of course if you need flames and stuff on stock turbo and engine at so point you need to replace both of them but again if done correctly most of the things will last long enough...

st10 or not code does the same thing on retard the ignition through the array or any other algorithm and do fuel or ignition cut at +100 or 150 rpm.
You can set the boost while doing that and deactivate b_kr or dmd algorithms while you are running the code.
i have posted something on st10 thread which applies to older me7.1.1 with c167 as well...

More help you will not get for free...So help yourself by reading around here
Logged
Pages: 1 ... 5 6 [7] 8 9 ... 21
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 22, 2024, 05:28:00 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.025 seconds with 18 queries. (Pretty URLs adds 0.001s, 0q)