NefMoto > Technical > NefMoto Software > NefMoto ME7 ECU Flasher and Data Logger Version 1.9.1.2 with Windows XP Support
Pages: 1 2 3 [4]
« previous next »
Author Topic: NefMoto ME7 ECU Flasher and Data Logger Version 1.9.1.2 with Windows XP Support  (Read 82619 times)
AndiS4
Full Member
***

Karma: +1/-0
Offline Offline

Posts: 117
Good to know.
So ignition cycle will now always be done first after beeing in programming mode.

I didnt flash anything yet, but maybe the d-box can now be listed up at the nefmoto software under tested vehicles, because i think if reading is possible, flashing should also be, doesnt it?
Logged
20VTMK1
Full Member
***

Karma: +0/-0
Offline Offline

Posts: 113
Hi ,

I get this error pack when trying to read my me7,5 ecu . I have no clue if this ecu is stock or not. The previous owner said that it might have a tune - he was not sure ..

29/May/2012 11:10:55.531: USER: ECU reports programming session preconditions have been met.
29/May/2012 11:10:55.531: USER: Negotiating communication timings.
29/May/2012 11:10:55.531: LOG: Reading current communication timings.
29/May/2012 11:10:55.593: LOG: Sent message with service ID AccessTimingParameters
29/May/2012 11:10:55.640: LOG: Received message with service ID: AccessTimingParametersPositiveResponse
29/May/2012 11:10:55.640: LOG: Set timing parameters to new values.
29/May/2012 11:10:55.640: LOG: Setting communication timing to defaults.
29/May/2012 11:10:55.703: LOG: Sent message with service ID AccessTimingParameters
29/May/2012 11:10:55.750: LOG: Received message with service ID: AccessTimingParametersPositiveResponse
29/May/2012 11:10:55.750: LOG: Reading current communication timings.
29/May/2012 11:10:55.812: LOG: Sent message with service ID AccessTimingParameters
29/May/2012 11:10:55.859: LOG: Received message with service ID: AccessTimingParametersPositiveResponse
29/May/2012 11:10:55.859: USER: Successfully changed to new communication timings.
29/May/2012 11:10:55.859: USER: Requesting security access.
29/May/2012 11:10:55.890: LOG: Sent message with service ID SecurityAccess
29/May/2012 11:10:55.937: LOG: Received message with service ID: NegativeResponse
29/May/2012 11:10:55.937: LOG: Received negative response for service ID: SecurityAccess, with response code: GeneralReject
29/May/2012 11:10:55.937: USER: ECU reports that security access request was rejected.
29/May/2012 11:10:55.937: LOG: Starting ProgrammingSession diagnostic session with 124800 baud rate.
29/May/2012 11:10:55.937: USER: Starting diagnostic session.
29/May/2012 11:10:55.968: LOG: Sent message with service ID StartDiagnosticSession
29/May/2012 11:10:56.031: LOG: Received message with service ID: NegativeResponse
29/May/2012 11:10:56.031: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending
29/May/2012 11:10:56.062: LOG: Received message with service ID: NegativeResponse
29/May/2012 11:10:56.062: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending
29/May/2012 11:10:56.109: LOG: Received message with service ID: NegativeResponse
29/May/2012 11:10:56.109: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending
29/May/2012 11:10:56.140: LOG: Received message with service ID: NegativeResponse
29/May/2012 11:10:56.140: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending
29/May/2012 11:10:58.218: LOG: Double checking receive buffer for embedded messages before flushing receive buffer due to P1 ECU response inter byte time out.
29/May/2012 11:10:58.218: LOG: Flushing 3 bytes from receive buffer due to P1 ECU response inter byte time out.
29/May/2012 11:11:06.000: LOG: Sent message with service ID TesterPresent
29/May/2012 11:11:06.109: LOG: Message received no replies.
29/May/2012 11:11:06.109: LOG: Resending message. Send attempts: 2
29/May/2012 11:11:06.125: LOG: Sent message with service ID TesterPresent
29/May/2012 11:11:06.234: LOG: Message received no replies.
29/May/2012 11:11:06.234: LOG: Resending message. Send attempts: 3
29/May/2012 11:11:06.250: LOG: Sent message with service ID TesterPresent
29/May/2012 11:11:06.359: LOG: Message received no replies.
29/May/2012 11:11:06.359: LOG: Failed to send message 3 times, message send failed.
29/May/2012 11:11:06.359: USER: Disconnecting because no response was received for the Tester Present message.
29/May/2012 11:11:06.359: USER: Disconnected
29/May/2012 11:11:06.359: USER: Reading ECU flash memory failed.
29/May/2012 11:11:06.875: LOG: Closing FTDI device.
29/May/2012 11:11:06.875: LOG: Send receive thread now terminated.
29/May/2012 11:11:08.906: USER: 100% complete.
29/May/2012 11:11:08.906: USER: Restoring Windows sleep mode.
Logged
Tony@NefMoto
Administrator
Hero Member
*****

Karma: +132/-4
Offline Offline

Posts: 1389


2001.5 Audi S4 Stage 3
Version 1.9.3.2 of the software is now available here: http://nefariousmotorsports.com/forum/index.php?topic=2200.0
Logged
Remember you have to log in if you want to see the file attachments!
Info or questions, please add to the wiki: http://www.nefariousmotorsports.com/wiki
Follow NefMoto developments on Twitter: http://twitter.com/nefmoto
Pages: 1 2 3 [4]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • April 05, 2025, 06:46:40 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.042 seconds with 14 queries. (Pretty URLs adds 0s, 0q)