Pages: [1] 2
Author Topic: DSLOFS and DSLGRAD 3bar map sensor  (Read 13008 times)
armageddon
Sr. Member
****

Karma: +20/-3
Offline Offline

Posts: 348


« on: July 29, 2017, 01:47:35 AM »

I have been using the 4bar map sensor without problem, but now I am using 3bar map 038906051A but theres a ~60mbar discrepancy between baro pressure and actual pressure at idle being actual pressure lower.

I remember julex had a similar problem that was caused by DSLGRAD / DSLOFS.

I am using DSLGRAD 658.82 and DSLOFS -63.51

Can anyone confirme if this is correct? and if so, what else could cause this?


« Last Edit: July 29, 2017, 03:07:53 AM by armageddon » Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #1 on: July 29, 2017, 09:35:51 AM »

You logged req pressure, not baro.
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
armageddon
Sr. Member
****

Karma: +20/-3
Offline Offline

Posts: 348


« Reply #2 on: July 29, 2017, 10:12:46 AM »

baro vs actual




Logged
dgpb
Full Member
***

Karma: +3/-3
Offline Offline

Posts: 176


« Reply #3 on: July 29, 2017, 12:53:26 PM »

I made this simple table for me some time ago and it works well. Hope it's useful for you too. Its calculations are already @3bar, but you'd better know the setup points for your specific sensor.

PS: Your calculation was wrong
« Last Edit: July 29, 2017, 12:56:27 PM by dgpb » Logged
armageddon
Sr. Member
****

Karma: +20/-3
Offline Offline

Posts: 348


« Reply #4 on: July 29, 2017, 12:57:58 PM »

thanks, will try those and report back

Logged
dgpb
Full Member
***

Karma: +3/-3
Offline Offline

Posts: 176


« Reply #5 on: August 14, 2017, 12:06:34 PM »

thanks, will try those and report back



Does it work?
Logged
armageddon
Sr. Member
****

Karma: +20/-3
Offline Offline

Posts: 348


« Reply #6 on: August 14, 2017, 05:00:14 PM »

not tested yet...
Logged
fknbrkn
Hero Member
*****

Karma: +176/-18
Offline Offline

Posts: 1401


mk4 1.8T AUM


« Reply #7 on: August 14, 2017, 10:00:23 PM »

658 / -59
Logged
Khendal
Full Member
***

Karma: +9/-8
Offline Offline

Posts: 226


« Reply #8 on: August 15, 2017, 06:06:11 AM »

I made this simple table for me some time ago and it works well. Hope it's useful for you too. Its calculations are already @3bar, but you'd better know the setup points for your specific sensor.

PS: Your calculation was wrong

With this formula is it possible to change map sensor and have it worked? For example changing the 2550mbar ori with a 3bar or 4 bar? Is it enough?
Logged
armageddon
Sr. Member
****

Karma: +20/-3
Offline Offline

Posts: 348


« Reply #9 on: October 26, 2017, 10:21:49 AM »

Sorry the late reply, but it was only possible to test today.

Still the same, whith dgpb values it reads the same diference

with fukenbroken values its even worst.

any clues?

could it be a bad sensor?

first log with dgpb values, second with fukenbroken values

I find various spec values for the sensor, but the more constant is 20-300kpa 0.4-4.65V that gives the DSLOFS/DSLGRAD on the first post.

regards

Logged
fknbrkn
Hero Member
*****

Karma: +176/-18
Offline Offline

Posts: 1401


mk4 1.8T AUM


« Reply #10 on: October 26, 2017, 05:06:22 PM »

im using the same sensor
with values i shared (if we talking about non-5120 file)

it shows ~ 960..980 mbar
« Last Edit: October 26, 2017, 06:01:04 PM by fukenbroken » Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #11 on: October 26, 2017, 05:45:23 PM »

Log voltage if possible.
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
GianniNOS
Jr. Member
**

Karma: +2/-0
Offline Offline

Posts: 37


« Reply #12 on: October 27, 2017, 02:07:28 AM »

when do you measure the engine is off?
Logged
armageddon
Sr. Member
****

Karma: +20/-3
Offline Offline

Posts: 348


« Reply #13 on: October 27, 2017, 02:10:20 AM »

On the last two logs yes,  first was runing.
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #14 on: October 27, 2017, 02:17:33 AM »

pointless until you log voltage.
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
Pages: [1] 2
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.02 seconds with 16 queries. (Pretty URLs adds 0s, 0q)