Pages: [1]
Author Topic: Audi TT 8j0920981c Cluster Corrupt Sware  (Read 7007 times)
Nogger
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« on: September 01, 2017, 10:05:37 AM »

Hi all, i have a TT Cluster 8j0920981c in which apparently the software is corrupt. It was displaying DEF and all lights were lit up (ABS etc). Now, on the bench it reads SAFE with all the lights on.  I understand there may be corruption of the Micronas and EEP software, i have taken dumps from the Micronas and the EEPROM.

Is ANYONE on here able to check these and advise if they are indeed corrupt or if they can correct for me.  2 or 3 people off other boards claim they could but couldn't.

Any help/advice greatly appreciated
Regards
Nogger
Logged
Nogger
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #1 on: September 04, 2017, 06:10:35 AM »

OK, as no one seems able to assist on repairing the corrupt files does anyone know where the SKC is stored (address) or what software would be capable of repairing these files
Thanks
Nogger
Logged
4ringpieces
Full Member
***

Karma: +4/-4
Offline Offline

Posts: 232


« Reply #2 on: September 04, 2017, 09:24:49 AM »

Upload your files.

What tool are you using to read the dash?
Logged
Nogger
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #3 on: September 04, 2017, 10:54:18 AM »

Files attached, i used XProg (original sware) to read the 24c32 and the Micronas. Fault was initially that display was lit up like a xmas tree with DEF on the display. At present powered up on bench it say SAFE and all lights on(pic attached)
Thanks
Nogger
Logged
Nogger
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #4 on: September 04, 2017, 11:01:02 AM »

Had to attach pics separately
Nogger
Logged
4ringpieces
Full Member
***

Karma: +4/-4
Offline Offline

Posts: 232


« Reply #5 on: September 04, 2017, 12:53:49 PM »

have you plugged back into the car and coded the key?
Logged
Nogger
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #6 on: September 04, 2017, 01:30:57 PM »

I don't have the car here, just cluster on bench, nothing has been changed since it was sent to me except i power on bench.
I know there will be lots of lights on when just on the bench but that was also the original fault, basically  i just need the flash and EEP checking to see if they are indeed corrupt
Nogger

Logged
aef
Hero Member
*****

Karma: +69/-46
Offline Offline

Posts: 1566


« Reply #7 on: September 04, 2017, 11:30:12 PM »

Your Xprog should be able to show and change you pin/skc and everything.
On DK someone wrote: If I chose "dashboards" / VW / Golf V from 07-2006 i can change vin/pin/km/serialnumber
Logged
Nogger
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #8 on: September 04, 2017, 11:59:44 PM »

That's what  i thought , maybe it's because i read the EEP & Fl;ash seperately.
Logged
Nogger
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #9 on: September 09, 2017, 10:10:37 AM »

Still got this issue ongoing, haven't had chance yet to re-read using XPROG Dashboard tool.

If anyone has experience with these Micronas/EEPROM dumps could you possibly have a look and advise if they are definitely corrupt. I reads somewhere that locations $A8610 to $F7FFF  must read only "FF" however mine doesn't , having said that that info was for an Audi A3 Micronas dump and this is a MK2 TT (2012)

Also, what is it that corrupts in these clusters ? is it the Micronas Flash, the eeprom or both?
Thanks
Nogger
« Last Edit: September 09, 2017, 10:12:20 AM by Nogger » Logged
focalpoint519
Full Member
***

Karma: +29/-63
Offline Offline

Posts: 148



« Reply #10 on: September 12, 2017, 12:28:04 AM »

anyone use SuperVAg on micronas cluster?
« Last Edit: September 12, 2017, 12:32:32 AM by focalpoint519 » Logged
Nogger
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #11 on: September 13, 2017, 12:40:36 AM »

Your Xprog should be able to show and change you pin/skc and everything.
On DK someone wrote: If I chose "dashboards" / VW / Golf V from 07-2006 i can change vin/pin/km/serialnumber

I have a secondhand Cluster which is identical to the one that is faulty except for the very last digit in the part no:

I have managed to read both clusters using the XProg Dashboard utility so i now have the vin/pin/km & serial number from both clusters. My question now is:

1:  If i change the vin/pin/km & serial number on this new cluster to that of the faulty one and write is this all that is required to clone the dash (will it enable the immobilser)

2:  Is the Serial number the same thing as SKC

If i am wrong in my assumptions then any advice on how to clone this repllacement cluster up (i only have XProg available at present) would be appreciated and all this is done on the bench (the car is over 100 miles away)

Thanks in advance
Nogger
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.066 seconds with 16 queries. (Pretty URLs adds 0.001s, 0q)