NefMoto > Technical > Flashing and Chipping > ME7.5.10 and 95040
Pages: [1]
« previous next »
Author Topic: ME7.5.10 and 95040  (Read 5236 times)
izoom
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4
« on: September 08, 2017, 02:46:11 AM »
I read my VW Polo ME7.5.10 ECU using Argdubs 95040 software in the car using a KKL cable. I made a change to the bin file but the softwear would not flash back into the eeprom. I read that this would not work and that it would have to be done on the bench. So I have got some wire, clips a battery. But I do not want to burnout any components or damage the ECU, so I am asking if anyone who has successfully flashed  to a ME7.5.10 using Argdubs 95040 software on the bench can show me a wiring diagram for the ECU PINS and using a VAG KKL USB cable setup. I have looked, but I want opinions on the best diagram/wiring for this,
izoom
Logged
adam-
Hero Member
*****

Karma: +124/-33
Offline Offline

Posts: 2179
« Reply #1 on: September 08, 2017, 05:36:36 AM »
There is no "best" wiring diagram.

Bootmode as usual.
Logged
fknbrkn
Hero Member
*****

Karma: +186/-24
Offline Offline

Posts: 1455


mk4 1.8T AUM
« Reply #2 on: September 11, 2017, 09:20:54 AM »
Logged
izoom
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4
« Reply #3 on: September 12, 2017, 04:23:45 AM »
Quote from: fukenbroken on September 11, 2017, 09:20:54 AM


ME7.5.10 bench read problem. Used the diagram for wiring, KKL cable in Com2, battery at 14Volts (can see it in device manage and is Ok, and LED is lit) I tried me7_eeprom.exe –OBD -r -p 2 95040.bin says connecting,  and I get the error fail 0x21007,

KKL cable was connections were…..
4, ground -
7, kline
16, 12 volts +

Whats wrong?

izoom
Logged
fknbrkn
Hero Member
*****

Karma: +186/-24
Offline Offline

Posts: 1455


mk4 1.8T AUM
« Reply #4 on: September 12, 2017, 04:46:31 AM »
that bench working good for me
what about vcds? is it connects? did you try bootmode?
Logged
izoom
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4
« Reply #5 on: September 12, 2017, 05:41:16 AM »
Quote from: fukenbroken on September 12, 2017, 04:46:31 AM
that bench working good for me
what about vcds? is it connects? did you try bootmode?
I can read the ME7.5.10 when it is in the car using me7_eeprom  and KKL cable , but cannot bench read it with me7_eeprom? Can I write to the ME7.5.10 in the car using me7_eeprom and KKL cable?
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 27, 2024, 12:47:12 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.017 seconds with 16 queries. (Pretty URLs adds 0s, 0q)