Kacza
Full Member
Karma: +20/-7
 Offline
Posts: 216
|
 |
« on: October 08, 2017, 12:11:02 PM »
|
|
|
I would like to raise the power in the Audi A3 2.0TFSI AXX.
I found a maps:
LDRXN
LDRXNZK
KFMIRL
KFMIOP
KFZW
KFZW2
KFLDIMX
KFLDRL
LAMFA
KFLBTS
KFFDLBTS
KFLDHBN
Usually in ME7 these maps were enough.
Is it enough for MED9 too? Do you need more maps?
|
|
|
|
|
Logged
|
|
|
|
|
gman86
|
|
« Reply #1 on: October 09, 2017, 12:14:11 AM »
|
|
|
KFPRSOLHKS, KFPRSOLHOM and KLPRMAX to give a little extra rail pressure.
|
|
|
|
|
Logged
|
|
|
|
bobbyz0r
Jr. Member
Karma: +3/-0
Offline
Posts: 43
|
|
« Reply #2 on: October 09, 2017, 03:07:02 PM »
|
|
|
KFMLDMX, KLDLUL and LDPBN might need editing as well.
|
|
|
|
|
Logged
|
|
|
|
|
birchbark506
|
|
« Reply #3 on: October 14, 2017, 05:02:00 AM »
|
|
|
what map again to disable the 02 sensor i can't remember
|
|
|
|
|
Logged
|
|
|
|
Kacza
Full Member
Karma: +20/-7
Offline
Posts: 216
|
|
« Reply #4 on: October 14, 2017, 01:42:59 PM »
|
|
|
OK I find maps: KFPRSOLHKS KFPRSOLHOM KLPRMAX KFMLDMX KLDLUL LDPBN Now I will tune the file.  O2 sensor: CDKATSP - 1DA17B |
|
|
|
|
Logged
|
|
|
|
|
birchbark506
|
|
« Reply #5 on: October 14, 2017, 03:49:02 PM »
|
|
|
i did that one i think it also has to be CDKAT
|
|
|
|
|
Logged
|
|
|
|
|
Rick
|
|
« Reply #6 on: October 14, 2017, 04:01:33 PM »
|
|
|
CDKAT is zero from factory
|
|
|
|
|
Logged
|
|
|
|
|
birchbark506
|
|
« Reply #7 on: October 14, 2017, 04:16:48 PM »
|
|
|
i always thought CDKAT should be 1 and then to disable 02 should be set to 0
|
|
|
|
|
Logged
|
|
|
|
Kacza
Full Member
Karma: +20/-7
Offline
Posts: 216
|
|
« Reply #8 on: October 14, 2017, 11:21:21 PM »
|
|
|
CDKATSP - 7
|
|
|
|
|
Logged
|
|
|
|
|
birchbark506
|
|
« Reply #9 on: October 15, 2017, 03:13:54 AM »
|
|
|
And CDKAT should be 0?
|
|
|
|
|
Logged
|
|
|
|
Kacza
Full Member
Karma: +20/-7
Offline
Posts: 216
|
|
« Reply #10 on: October 15, 2017, 04:02:48 AM »
|
|
|
Yes
|
|
|
|
|
Logged
|
|
|
|
|
birchbark506
|
|
« Reply #11 on: October 15, 2017, 04:04:25 AM »
|
|
|
Okay I must of found it then but I still can't get the 02 to disable with CDKATSP I'm working on 7115B sw0040 file for mk5 vw Jetta 2.0 tfsi
|
|
|
|
|
Logged
|
|
|
|
|
birchbark506
|
|
« Reply #12 on: October 15, 2017, 05:15:05 AM »
|
|
|
i think i have found it and it looks like the address on my file was 1DAD79 for CDKATSP i set to 0 and i am going to reflash and go for a drive and see if it throw the DTC for bank 1
|
|
|
|
|
Logged
|
|
|
|
Kacza
Full Member
Karma: +20/-7
Offline
Posts: 216
|
|
« Reply #13 on: October 15, 2017, 11:37:40 AM »
|
|
|
I have errors in the car:
008200 P2008
012600 P3138
What can I do with it?
Can I turn off the Intake Manifold Flaps?
I will add that Intake Manifold Flaps are clean.
|
|
|
|
|
Logged
|
|
|
|
|
gman86
|
|
« Reply #14 on: October 15, 2017, 01:18:52 PM »
|
|
|
I have errors in the car:
008200 P2008
012600 P3138
What can I do with it?
Can I turn off the Intake Manifold Flaps?
I will add that Intake Manifold Flaps are clean.
Check the linkage arm hasn't been disconnected. It's not wise to delete the flaps if they still exist unless you can pin them open. In which case, the flaps can be deleted in SW |
|
|
|
|
Logged
|
|
|
|
|
