NefMoto > Noob Zone > Noob Questions (Moderator: turboat) > Noob alert. How d hell do i change these offsets?!
Pages: [1]
« previous next »
Author Topic: Noob alert. How d hell do i change these offsets?!  (Read 4599 times)
GocaMo
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9
« on: November 17, 2017, 02:48:02 PM »
Ok, i'm tryin to delete EGTs on my S4 B5 D box. I installed tunerpro, looked for proper XDF file (i think i found it but if someone has proper D box XDF file i would be greatful), i have my bin file from my ecu, did lots of reading till my eyes bled out, tryin to learn about Tunerpro and i'm stuck on changing offsets in CDATR, CDATS etc. S4 wiki says that i change these offsets:

EGT
Removal

If you want to disable your EGT sensors:[64] (Note that my old M-box xdf is wrong[65] for CDATR/ATS. Please use these offsets.)

    CDATR (0x18196) - Configuration byte diagnosis exhaust gas temperature regulation
    CDATS (0x18197) - Configuration byte diagnosis exhaust gas temperature sensor
    CATR (0x192CA) - Configuration byte exhaust gas temperature regulation (disables ATR)[66][67][68]

Alternately, setting both of these to their maximum (1229) may help: [69]

    TABGSS (0x1C514) and TABGSS2 (0x1C516) - Desired exhaust gas temperature for EGT regulation

You shouldn't have to touch these, but are included here for completeness:

    CLAATR - Error class exhaust gas temperature regulation
    CLAATR2 - Error class exhaust gas temperature regulation bank 2
    CLAATS - Error class exhaust gas temperature sensor
    CLAATS2 - Error class exhaust gas temperature sensor bank 2


But change offsets how and where?!?

I've got this in TP, can someone please tell me what should change and how  Huh Huh Huh
Logged
KasperH
Hero Member
*****

Karma: +24/-8
Offline Offline

Posts: 630
« Reply #1 on: November 17, 2017, 03:49:40 PM »
address is correct and value looks correct, so i cant really see where the problem is?
or am i missing something?
Logged
GocaMo
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9
« Reply #2 on: November 17, 2017, 03:52:35 PM »
Quote from: KasperH on November 17, 2017, 03:49:40 PM
address is correct and value looks correct, so i cant really see where the problem is?
or am i missing something?

Value is correct? What value? That's my question exactly, what value should I change o.O?
Logged
KasperH
Hero Member
*****

Karma: +24/-8
Offline Offline

Posts: 630
« Reply #3 on: November 17, 2017, 05:59:43 PM »
You need to understand the changes you make, before you make them.

The changes you want to make is described in detail with a guide.
And you still don't know what to do.

For your own sake, don't do anything until you know what you are changing.
You will likely damage your ECU or engine.

Unless you accept that risk, then go ahead and do whatever you like Smiley

And don't take this as a slap in the face but rather motivation to learn
a new skill that will give you a lot of fun.

This forum have all the info you'll need, and if it's not there.
The are some VERY skilled people here that is willing to help,
provided they don't need to spoon feed you everything and you do the hard work yourself.

Welcome to the forum, see you around Smiley

P.S.
the slider in the scalar should be all the way to the left, so the 1 becomes a 0. (So I don't leave you empty handed)
Logged
fknbrkn
Hero Member
*****

Karma: +185/-23
Offline Offline

Posts: 1454


mk4 1.8T AUM
« Reply #4 on: November 17, 2017, 06:44:28 PM »
the value is 1
the offset is 0x18186; its a value location in your bin

change value to 0 to disable diagnosis
and do not forget about checksum

pretty simple
Logged
GocaMo
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9
« Reply #5 on: November 18, 2017, 12:04:05 AM »
Quote from: fukenbroken on November 17, 2017, 06:44:28 PM
the value is 1
the offset is 0x18186; its a value location in your bin

change value to 0 to disable diagnosis
and do not forget about checksum

pretty simple

Well it is simple, but not mentioned anywhere. Was it so hard to mention - slider should be to the left all the way so value is 0  Roll Eyes? Anyway thank you for the advice.
Logged
GocaMo
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9
« Reply #6 on: November 18, 2017, 12:10:03 AM »
Quote from: KasperH on November 17, 2017, 05:59:43 PM
You need to understand the changes you make, before you make them.

The changes you want to make is described in detail with a guide.
And you still don't know what to do.

For your own sake, don't do anything until you know what you are changing.
You will likely damage your ECU or engine.

Unless you accept that risk, then go ahead and do whatever you like Smiley

And don't take this as a slap in the face but rather motivation to learn
a new skill that will give you a lot of fun.

This forum have all the info you'll need, and if it's not there.
The are some VERY skilled people here that is willing to help,
provided they don't need to spoon feed you everything and you do the hard work yourself.

Welcome to the forum, see you around Smiley

P.S.
the slider in the scalar should be all the way to the left, so the 1 becomes a 0. (So I don't leave you empty handed)

Thank you sir also, it's a good advice i'll try to learn as much as possible  Smiley
Logged
GocaMo
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9
« Reply #7 on: November 18, 2017, 12:16:21 AM »
So it should look like this if i'm not wrong?
Logged
GocaMo
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9
« Reply #8 on: November 18, 2017, 12:55:32 AM »
Of course there's no CATR in scalars cause i don't have right XDF... i mean there's no right file for D box anywhere  Sad.... back to the drawing board...
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12268


WWW
« Reply #9 on: November 18, 2017, 01:24:23 AM »
why not switch to m
Logged
ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
GocaMo
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9
« Reply #10 on: November 18, 2017, 04:38:30 AM »
Quote from: nyet on November 18, 2017, 01:24:23 AM
why not switch to m

Gladly, but you're tellin a noob to switch from A to Y Cheesy. As I understood, hardware is same, I just need to make adjustments cause M is Hitachi and D is Bosch MAF. And M has perfectly good XDF file. Need to learn more Smiley
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 25, 2024, 08:33:44 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.037 seconds with 18 queries. (Pretty URLs adds 0.001s, 0q)