|
eliotroyano
|
 |
« Reply #90 on: August 14, 2014, 08:13:14 AM »
|
|
|
does anybody know how to delete errors in this older motronics?
would like to remove 18259 - Powertrain Data Bus: Missing Message from ABS Controller P1851 - 35-10
You can clean DTC errors in eeprom dump, make it FF after backup zone. Check it out:  Also here are located adaptation channels. Test it. |
|
|
|
« Last Edit: August 14, 2014, 08:16:52 AM by eliotroyano »
|
Logged
|
|
|
|
|
aef
|
|
« Reply #91 on: August 14, 2014, 02:18:50 PM »
|
|
|
So i have to clear Codes with vagcom, read out the Clean eeprom with monoscan.
Then run it in the Car to Set the Error, read it out again and compare?
Or is there another Way to find the right Spot?
|
|
|
|
|
Logged
|
|
|
|
|
eliotroyano
|
|
« Reply #92 on: August 14, 2014, 06:04:36 PM »
|
|
|
So i have to clear Codes with vagcom, read out the Clean eeprom with monoscan.
Then run it in the Car to Set the Error, read it out again and compare?
Yes that way it should work. |
|
|
|
|
Logged
|
|
|
|
|
aef
|
|
« Reply #93 on: August 15, 2014, 11:25:06 AM »
|
|
|
I tried it on the bench. unfortunately the ABS / Powerbrake error was not included.
Looks like i have to find the software way in the flash...
|
|
|
|
|
Logged
|
|
|
|
grey
Full Member
Karma: +4/-1
 Offline
Posts: 146
|
|
« Reply #94 on: November 18, 2014, 08:02:26 AM »
|
|
|
Hi guys,
I have a 8D0907557T - Bosch M3.8.2 (1.8T AEB)
The chip is a 27C1024, and i changed with M28F102
Now,can i do flashed via MPPS bench flash?
|
|
|
|
|
Logged
|
|
|
|
technic
Full Member
Karma: +18/-5
Offline
Posts: 227
|
|
« Reply #95 on: November 18, 2014, 08:23:02 AM »
|
|
|
No
|
|
|
|
|
Logged
|
|
|
|
|
TCSTigersClaw
|
|
« Reply #96 on: November 18, 2014, 11:49:20 AM »
|
|
|
Flashing is not a function of the eeprom ,but of the proccessor  |
|
|
|
|
Logged
|
VAG cars newbie tuner  |
|
|
grey
Full Member
Karma: +4/-1
Offline
Posts: 146
|
|
« Reply #97 on: November 18, 2014, 12:11:42 PM »
|
|
|
No
Flashing is not a function of the eeprom ,but of the proccessor Thanks,so certainly necessary a epromreader  |
|
|
|
|
Logged
|
|
|
|
|
eliotroyano
|
|
« Reply #98 on: November 18, 2014, 02:43:03 PM »
|
|
|
Thanks,so certainly necessary a epromreader That´s right. But I have seen that many maps needed for ECU operation are uploaded to RAM, and can be readed. Also good areas of flash eeprom can be read, but not completely. Also factory test code (Reset or Boot secuence) does not include code to access serial or flash eeproms. |
|
|
|
|
Logged
|
|
|
|
technic
Full Member
Karma: +18/-5
Offline
Posts: 227
|
|
« Reply #99 on: November 18, 2014, 04:13:37 PM »
|
|
|
Thanks,so certainly necessary a epromreader Yes, and also be aware that the 28F102 use completely different programming algorithms than your old 27C1024. Something to think of when you buy a programmer |
|
|
|
|
Logged
|
|
|
|
|
eliotroyano
|
|
« Reply #100 on: November 18, 2014, 06:06:31 PM »
|
|
|
Friends a question, I have seen some kinf of module that can replace a flash eeprom with a module that simulates eeprom itself but also have a serial port that allow memory to be flashed. I have some brands like Xilink, but do you know which boards are those?
|
|
|
|
|
Logged
|
|
|
|
grey
Full Member
Karma: +4/-1
Offline
Posts: 146
|
|
« Reply #101 on: November 19, 2014, 06:06:58 AM »
|
|
|
Yes, and also be aware that the 28F102 use completely different programming algorithms than your old 27C1024. Something to think of when you buy a programmer Thank you for informations I think a GQ-4X Willem Programmer and ADP-054,it works? |
|
|
|
|
Logged
|
|
|
|
|
eliotroyano
|
|
« Reply #102 on: November 19, 2014, 06:27:58 AM »
|
|
|
Thank you for informations
I think a GQ-4X Willem Programmer and ADP-054,it works?
I have been using a GQ-4X with great sucess. Also GQ-3X, TL866 and other eeprom programmers will work with it associated adapter. |
|
|
|
|
Logged
|
|
|
|
grey
Full Member
Karma: +4/-1
Offline
Posts: 146
|
|
« Reply #103 on: November 19, 2014, 06:29:37 AM »
|
|
|
I have been using a GQ-4X with great sucess. Also GQ-3X, TL866 and other eeprom programmers will work with it associated adapter.
Thanks Elio  |
|
|
|
|
Logged
|
|
|
|
jona29
Newbie
Karma: +1/-1
Offline
Posts: 22
|
|
« Reply #104 on: December 13, 2014, 09:39:01 PM »
|
|
|
without reading through all the thread as its 4.30 am , is the immo data stored in the 24c02 on these and if so is it possible to access the eeprom while on the board without an eeprom programmer . i.e with other software . or do i need to purchase a new eeprom reader as my clone carprog seems it cannot read eeproms wether on or off the board .
|
|
|
|
|
Logged
|
|
|
|
|
