m_haiser
Full Member
Karma: +0/-2
 Offline
Posts: 68
|
 |
« Reply #15 on: May 07, 2018, 07:56:31 PM »
|
|
|
alright, does this appear to be a good read on the 95040?
if so, does the me7eeprom tool write over obd yet or still boot mod only?
thanks guys!
|
|
|
|
|
Logged
|
|
|
|
|
adam-
|
|
« Reply #16 on: May 07, 2018, 11:31:13 PM »
|
|
|
It's bootmode only.
|
|
|
|
|
Logged
|
|
|
|
m_haiser
Full Member
Karma: +0/-2
Offline
Posts: 68
|
|
« Reply #17 on: May 08, 2018, 09:40:49 AM »
|
|
|
damn that's what I was afraid of. alright well did you by chance check out the read and see if it is correct/complete?
|
|
|
|
|
Logged
|
|
|
|
m_haiser
Full Member
Karma: +0/-2
Offline
Posts: 68
|
|
« Reply #18 on: May 17, 2018, 05:10:12 PM »
|
|
|
sucessfully crossflashed just now, maiden voyage will be on the way home from work (what better place to have car troubles than a dealership) surprisingly no key light or immo issues. wish me luck!
|
|
|
|
|
Logged
|
|
|
|
m_haiser
Full Member
Karma: +0/-2
Offline
Posts: 68
|
|
« Reply #19 on: May 17, 2018, 09:25:08 PM »
|
|
|
spoke too soon. immediately after flash the car started, but later on it wouldnt and neither nefmoto nor vcds will connect to the ecu so now it is bricked. and when i try to use galletto (albeit a bootleg copy, it says "Start data reading...Opening port impossible"
please help this is my only car
|
|
|
|
|
Logged
|
|
|
|
|
aef
|
|
« Reply #20 on: May 17, 2018, 11:25:32 PM »
|
|
|
Is Galletto working with com port? Which port does galletto listen too und which port does the cable actually use in device manager?
|
|
|
|
|
Logged
|
|
|
|
|
adam-
|
|
« Reply #21 on: May 18, 2018, 03:21:05 AM »
|
|
|
Did you checksum the file?
|
|
|
|
|
Logged
|
|
|
|
m_haiser
Full Member
Karma: +0/-2
Offline
Posts: 68
|
|
« Reply #22 on: May 18, 2018, 08:36:41 AM »
|
|
|
realized after it was too late I did not checksum the file (which I did after realizing it but that doesn't help unless I can unbrick).
Im not sure what port galetto uses, how do I find out? my cable typically uses com port 4
|
|
|
|
|
Logged
|
|
|
|
m_haiser
Full Member
Karma: +0/-2
Offline
Posts: 68
|
|
« Reply #23 on: May 18, 2018, 10:36:42 AM »
|
|
|
Second pin from the left bottom of chip is boot pin correct? Can't seem to get into boot mode at all  Sent from my Z917VL using Tapatalk |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #24 on: May 18, 2018, 11:02:13 AM »
|
|
|
You are using galletto to write the flash or the eeprom?
They are two very different things.
|
|
|
|
|
Logged
|
|
|
|
m_haiser
Full Member
Karma: +0/-2
Offline
Posts: 68
|
|
« Reply #25 on: May 18, 2018, 11:14:36 AM »
|
|
|
trying to use it to write the flash after having flashed with a non checksum-ed file and bricked the ecu. may very well need to rewrite the eeprom later but ill cross that bridge when I come to it.
|
|
|
|
|
Logged
|
|
|
|
m_haiser
Full Member
Karma: +0/-2
Offline
Posts: 68
|
|
« Reply #26 on: May 18, 2018, 04:02:13 PM »
|
|
|
well I am not getting "boot mode inactive" so the com port issue is resolved but nothing else. please help
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #27 on: May 18, 2018, 04:08:24 PM »
|
|
|
did you flash a checksummed file?
|
|
|
|
|
Logged
|
|
|
|
m_haiser
Full Member
Karma: +0/-2
Offline
Posts: 68
|
|
« Reply #28 on: May 18, 2018, 04:11:21 PM »
|
|
|
the file I flashed yesterday was not checksummed. I now cannot connect to the ecu to reflash
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #29 on: May 18, 2018, 04:13:32 PM »
|
|
|
You said you are not getting "boot mode inactive", which means galletto should be able to flash it in boot mode.
|
|
|
|
|
Logged
|
|
|
|
|
