NefMoto > Noob Zone > Noob Guides and FAQs (Moderator: turboat) > ME7 ECU Coding Chart / Guide
Pages: [1] 2
« previous next »
Author Topic: ME7 ECU Coding Chart / Guide  (Read 45593 times)
Nosbeui
Newbie
*

Karma: +16/-2
Offline Offline

Posts: 19
« on: April 09, 2018, 08:09:52 AM »
Hey all this is compiled from VCDS definitions and other knowledge to make a more complete reference table for the coding stored in EEPROM.

16bit value located in EEPROM 7A,7B and 8A,8B (reverse values ex. 7E1D becomes 1D7E or 07550 in decimal)


Engine (J220) Coding
   00??xxx: Country/Emissions
      04 = Japan/EURO 2 & Mexico/Tier-I w/o SAI
      05 = Rest of World EURO 2 D3/D4 w/SAI
      06 = USA TLEV
      07 = USA LEV
      08 = China/Russia
      10 = Europe EURO 3
      11 = Rest of World/Japan EURO 4
      13 = North America LEV-II
      16 = North America ULEV
      25 = South Africa
      26 = Vapor-Pressure Critical
      27 = Brazil/Mexico
   00xx?xx: Powertrain
      0 = Front-Wheel-Drive (FWD) w/o ASR/ESP w/o CAN
      2 = All-Wheel-Drive (AWD) w/o CAN
      4 = All-Wheel-Drive (AWD) w/o ASR + CAN
      5 = Front-Wheel-Drive (FWD) with ESP + CAN
      6 = All-Wheel-Drive (AWD) w/o ESP + CAN
      7 = All-Wheel-Drive (AWD) with ESP + CAN
      8 = All-Wheel-Drive with Post-Switch Stage (Low Range - A6 Allroad only)
   00xxx?x: Transmission
      0 = 5-Speed Manual Transmission
      1 = 6-Speed Manual Transmission
      5 = Automatic Transmission (01V/5HP19/09A)
      7 = Automatic Transmission
      8 = Multitronic/CVT (01J/VL30)
   00xxxx?: Vehicle
      0 = Audi A3 A chassis (TT/VW Golf)
      1 = Audi A4 B chassis (VW Passat)
      2 = Audi A6 C chassis
      3 = Audi A8 D chassis (VW Phaeton)
      4 = Audi A4 Cabriolet (8H)
      5 = Audi A6 Allroad (4BH / excl. Engine Code APB)
« Last Edit: April 09, 2018, 08:25:55 AM by Nosbeui » Logged
tao13
Sr. Member
****

Karma: +107/-157
Offline Offline

Posts: 495
« Reply #1 on: July 10, 2018, 03:24:00 AM »
It is stored in eeprom only or it is in flash and after is write in eeprom?
Logged
nyet
Administrator
Hero Member
*****

Karma: +609/-169
Offline Offline

Posts: 12281


WWW
« Reply #2 on: July 10, 2018, 05:50:55 AM »
In general, the ECU can't modify its own flash unless it is in programming mode (or obviously bootmode)
Logged
ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
tao13
Sr. Member
****

Karma: +107/-157
Offline Offline

Posts: 495
« Reply #3 on: July 10, 2018, 12:07:05 PM »
DEAR NYET
Like every time your answer is very very very amigous
The right word is ambigous but i wrote very very very because 99% times i don't understood your explanation.
Mybe i'm stupid but...............
Thanks again for your time
Logged
nupustas
Full Member
***

Karma: +3/-7
Offline Offline

Posts: 122
« Reply #4 on: February 16, 2019, 10:47:06 AM »
Hi, i need to change ecu soft coding, because i made my car awd from fwd. Ecu ME7.5, coding 00002. Another car, from which i take all parts has ME7.1.1 ecu with coding 00132. Both coding doesnt mach with chart in this page.  What should i to do next - take coding from ME7.1.1 ecu or create new by chart in this page?
Logged
fknbrkn
Hero Member
*****

Karma: +192/-24
Online Online

Posts: 1483


mk4 1.8T AUM
« Reply #5 on: February 16, 2019, 10:57:54 AM »
All possible variants stored in VARTAB (vardef has default one)
« Last Edit: August 16, 2023, 06:39:02 PM by fknbrkn » Logged
nupustas
Full Member
***

Karma: +3/-7
Offline Offline

Posts: 122
« Reply #6 on: February 16, 2019, 12:36:29 PM »
Quote from: fukenbroken on February 16, 2019, 10:57:54 AM
All possible variants stored in VARDEF

search shows only 2 result for "vardef", i found .csv file there ir vardef ant thats all. I dont know that to do with this file
Logged
bazgreener
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 10
« Reply #7 on: July 20, 2022, 10:11:14 AM »
Hi ,  I have swapped a manual trans into my A3 1.8T and have changed the EEPROM coding from 0011550 to 0011500 but the ECU/ABS & Cluster are still looking for comms from the TCU. I've looked at the ABS and cluster coding but there doesn't appear to be any changes i can make that relate to the auto trans.
Any ideas what i'm missing?

thanks
Logged
denniss112
Full Member
***

Karma: +7/-1
Offline Offline

Posts: 114


Audi TT 99' | 180+HP FWD
« Reply #8 on: July 20, 2022, 03:44:07 PM »
Quote from: bazgreener on July 20, 2022, 10:11:14 AM
Hi ,  I have swapped a manual trans into my A3 1.8T and have changed the EEPROM coding from 0011550 to 0011500 but the ECU/ABS & Cluster are still looking for comms from the TCU. I've looked at the ABS and cluster coding but there doesn't appear to be any changes i can make that relate to the auto trans.
Any ideas what i'm missing?

thanks

did it save the 0011500 coding? Sometimes you need to login in order to save the changes.
Logged
fknbrkn
Hero Member
*****

Karma: +192/-24
Online Online

Posts: 1483


mk4 1.8T AUM
« Reply #9 on: July 20, 2022, 05:33:34 PM »
Quote from: bazgreener on July 20, 2022, 10:11:14 AM
Hi ,  I have swapped a manual trans into my A3 1.8T and have changed the EEPROM coding from 0011550 to 0011500 but the ECU/ABS & Cluster are still looking for comms from the TCU. I've looked at the ABS and cluster coding but there doesn't appear to be any changes i can make that relate to the auto trans.
Any ideas what i'm missing?

thanks

Tip ecus cannot be recoded to manual, reflash it first
What make some people seriously think that if its cannot be changed with vcds, changing it in eeprom solve all? thats not how the things work
Logged
bazgreener
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 10
« Reply #10 on: July 21, 2022, 12:12:17 PM »
Quote from: fukenbroken on July 20, 2022, 05:33:34 PM
Tip ecus cannot be recoded to manual, reflash it first
What make some people seriously think that if its cannot be changed with vcds, changing it in eeprom solve all? thats not how the things work

Do you mean i cannot use the auto ecu or i need to flash a manual file to it?

thanks
Logged
nyet
Administrator
Hero Member
*****

Karma: +609/-169
Offline Offline

Posts: 12281


WWW
« Reply #11 on: July 21, 2022, 06:06:03 PM »
Quote from: bazgreener on July 21, 2022, 12:12:17 PM
Do you mean i cannot use the auto ecu or i need to flash a manual file to it?

thanks

Most ME7.1 ECUs have trans specific ECUs flash PNs and cannot be recoded. You have to flash the right file.
Logged
ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
bamofo
Sr. Member
****

Karma: +34/-3
Offline Offline

Posts: 420
« Reply #12 on: August 02, 2022, 09:53:01 AM »
your best bet is to share your files, get the manual version of it, update the eeprom based off the vartab like mentioned above and checksum and flash both files..

Logged
Spawnb91rlf
Newbie
*

Karma: +0/-3
Offline Offline

Posts: 4
« Reply #13 on: August 16, 2023, 08:40:31 AM »
Hello
Please help me with a stock 1.8T AMK file to communicate with the automatic gearbox, I installed a DSG DQ250 6 speed gearbox and it doesn't communicate with it.
I tried to recode the ecu and I didn't succeed. It communicates ok with the ABS unit.
My stock file is 8N0906018AG 0261207213 360320 and the coding is 11500.
I understood that it should be coded to 11570, and I didn't manage to do that. 
Maybe someone can help me.
Thank you
Logged
fknbrkn
Hero Member
*****

Karma: +192/-24
Online Online

Posts: 1483


mk4 1.8T AUM
« Reply #14 on: August 16, 2023, 06:37:53 PM »
8N0906018BC is your choice
Or 06A906032HF
Logged
Pages: [1] 2
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • February 16, 2025, 01:29:39 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 1.341 seconds with 17 queries. (Pretty URLs adds 0.00099999999999989s, 0q)