Searching for xdf file for A4 1.8T AT AMB'02 8E0909518F SW 360910

Pages: [1]

« previous next »

Author

Topic: Searching for xdf file for A4 1.8T AT AMB'02 8E0909518F SW 360910 (Read 6967 times)

Tim Taler

Newbie

Karma: +0/-0
Offline

Offline

Posts: 4

	Searching for xdf file for A4 1.8T AT AMB'02 8E0909518F SW 360910 « on: May 07, 2018, 01:29:47 AM »

Hello!

I'm looking for a XDF file for a Audi A4 1.8T AT (Tiptronic) with AMB engine. All i have found are not the right i believe.

Are ECU data or the addresses of the individual maps from cars with automatic transmission the same as from manuell transmission?

I can not get any further Sad

, ask you for help...

Thanks!


	Logged

Tim Taler

Newbie

Karma: +0/-0
Offline

Offline

Posts: 4

	Re: Searching for xdf file for A4 1.8T AT AMB'02 8E0909518F SW 360910 « Reply #1 on: May 07, 2018, 02:04:10 AM »

Sorry, here is my currently ECU file....


	Logged

gt30avant

Newbie

Karma: +0/-0
Offline

Offline

Posts: 9

	Re: Searching for xdf file for A4 1.8T AT AMB'02 8E0909518F SW 360910 « Reply #2 on: May 11, 2018, 03:13:48 AM »

maybe this will help


	Logged

Tim Taler

Newbie

Karma: +0/-0
Offline

Offline

Posts: 4

	Re: Searching for xdf file for A4 1.8T AT AMB'02 8E0909518F SW 360910 « Reply #3 on: May 14, 2018, 11:11:39 PM »

Everything helps, thank you very much!

I think i must disable torque monitoring and can not found

TMNSMN
TANSMN
NASNOTKL

Is Table KFMIZUOF adress correct in this XDF?

Problem i have is, if i have WOT and boost over 21 psi, i get a load error "18265.P1857 Load Signal error" to engine control unit and "Load Signal error message from engine control unit" + "01119.Gear recognition signal" to gearbox unit. And engine goes in one second in limp mode...no boost.

If i delete errors, i have boost for one second and again limp mode.....

Anyone can help?


	Logged

Tim Taler

Newbie

Karma: +0/-0
Offline

Offline

Posts: 4

	Re: Searching for xdf file for A4 1.8T AT AMB'02 8E0909518F SW 360910 « Reply #4 on: May 14, 2018, 11:23:42 PM »

...i forgot when i get the load error - ASR lamp is on, maybe that's important ?


	Logged

aleckerchner

Newbie

Karma: +0/-0
Offline

Offline

Posts: 15

	Re: Searching for xdf file for A4 1.8T AT AMB'02 8E0909518F SW 360910 « Reply #5 on: February 03, 2020, 07:41:55 PM »

Sorry for the old bump, but this is the same setup i am working on. I am using the .XDF that was so generously provided here. However when i open my bin and ESKONF table, all i get is zero's. I just deleted all emissions and am looking to self tune them out. Not asking for someone to do it for me, but can someone check that the bin i pulled looks correct?

Thanks,
Alec


	Logged

Pages: [1]

« previous next »

Jump to:

Navigation

Personal Tools

November 25, 2024, 10:55:08 AM

Welcome, Guest. Please login or register.
Did you miss your activation email?