Pages: [1]
Author Topic: ME7Logger not working  (Read 1147 times)
ibizaCUPRA18t
Full Member
***

Karma: +2/-26
Offline Offline

Posts: 151


« on: June 28, 2018, 06:46:41 AM »

Hi, I've setup ME7logger gui, selected my correct com port. I am using a VAG178 Dual-K CAN -> USB cable from a clone VCDS. I went to vcds, disabled "Boot in Intelligent Mode" and tried to log, but no connection. Do I need to download some kind of drivers, kinda worried I won't be able to use vcds afterwards.

Me7logger error log attached in Notepad. Also here copy pasted.

-> Reading log config file C:\xampp\htdocs\logs\MadsCopyCupraRONIv5_template.cfg
 .... done
-> Reading ecu characteristics file C:\xampp\htdocs\ecus\MadsCopyCupraRONIv5.ecu
 .... done
Used Ecu definition is:
[Communication]
Connect      = SLOW-0x11
Communicate  = HM0
LogSpeed     = 56000

[Identification]
HWNumber           = "0261207071"
SWNumber           = "1037354562"
PartNumber         = "6K0906032AA"
EngineId           = "RONITuned 20V"

Logged variables are:
#no.: name                , alias                           , addr  ,sz, bitm, S
, I,  A         ,   B, unit
#-------------------------------------------------------------------------------
-----------------------------
#001: dwkrz_0             , IgnitionRetardCyl1              , 380BC7, 1, 0000, 1
, 0,        0.75,   0, '¬¶KW'
Logged data size is 1 bytes.
Really logged are 1 entries with 1 bytes.
Start connecting to ECU at 28.06.2018 12:55:48.553
try connect slow(11)
try connect slow(11)
Could not connect
try connect slow(11)
12:55:54.065-031,6 os_setspeed(speed=10400)
12:55:54.067-666,3 os_receiver_off()
12:55:54.369-823,9 os_setbreak()
12:55:54.569-824,1 os_clrbreak()
12:55:54.769-823,9 os_setbreak()
12:55:54.969-823,8 os_setbreak()
12:55:55.169-823,2 os_setbreak()
12:55:55.369-823,5 os_clrbreak()
12:55:55.569-822,9 os_setbreak()
12:55:55.769-823,1 os_setbreak()
12:55:55.969-822,6 os_setbreak()
12:55:56.169-822,4 os_clrbreak()
12:55:56.171-270,6 os_receiver_on()
12:55:56.677-162,1 os_rcvbyte(timeout=500) -> TIMEOUT
try connect slow(11)
12:55:56.679-378,6 os_setspeed(speed=10400)
12:55:56.680-961,8 os_receiver_off()
12:55:56.982-342,9 os_setbreak()
12:55:57.182-342,8 os_clrbreak()
12:55:57.382-343,0 os_setbreak()
12:55:57.582-342,4 os_setbreak()
12:55:57.782-342,7 os_setbreak()
12:55:57.982-342,1 os_clrbreak()
12:55:58.182-341,9 os_setbreak()
12:55:58.382-342,2 os_setbreak()
12:55:58.582-341,6 os_setbreak()
12:55:58.782-341,9 os_clrbreak()
12:55:58.783-923,4 os_receiver_on()
12:55:59.288-988,2 os_rcvbyte(timeout=500) -> TIMEOUT
Could not connect
=> Could not connect to ECU, exiting ...
=> Logging failed
exiting (cause=0x4)...

C:\xampp\htdocs>
Logged
adam-
Hero Member
*****

Karma: +96/-24
Offline Offline

Posts: 1833


« Reply #1 on: June 28, 2018, 07:17:03 AM »

Disconnect cluster fuse.  A lot of this is already covered.
Logged
ibizaCUPRA18t
Full Member
***

Karma: +2/-26
Offline Offline

Posts: 151


« Reply #2 on: June 28, 2018, 03:10:53 PM »

Disconnect cluster fuse.  A lot of this is already covered.

Ok. I think I need to download those drivers since I'm using a vag cable. Will try with drivers then if it doesn't work just fuse. Thanks
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.017 seconds with 16 queries. (Pretty URLs adds 0s, 0q)