Pages: [1]
Author Topic: 022906032EG r32 mk4 def needed! thank you!  (Read 3159 times)
up50lut3
Full Member
***

Karma: +1/-0
Offline Offline

Posts: 55


« on: July 30, 2018, 09:56:44 PM »

hey all,

i can't find a damos or xdf for my ecu.. ive tried others to compare but to no avail.

I still have the rear 02's but no cats. i can either delete them or numb them to go through emissions but i cant figure out which bit is what for ither situation

anyone with a little insight as to whats what would be much appreciated

0x18194 is where control bits start.

i have the are where the control bits are but cant find the correct addresss for

You maybe able to numb ME7's sensitivity (note: untested) using: [55][56]

AHKATMN (0x18672) - leave alone
AHKATMX (0x18673) - set to max
AHKATS (0x18674) - set to max
AHKATSB (0x18675) - set to max

....or


 CDHSH - Post cat O2 heater diagnosis
CDHSHE - Post cat O2 heater amplifier diagnosis
CDLATV - Lambda sensor aging diagnosis (tv) in OBDII-Mode (inverse: EURO-Mode)
CDLASH - Lambda sensor aging diagnosis (SHK) in OBDII-Mode (inverse: EURO-Mode)
CDLSH - Post cat O2 sensor diagnosis
CDLSHV - Lambda sensor sensor interchange recognition (N/A for vehicles equipped with a single post cat sensor, IE 1.8t and certain vr6)
CWKONLS (0x181BB) - Vehicles with 4 installed sensors - change from 51 (0x33/00110011b) to 17 (0x11/00010001b)[58] Vehicles with 2 installed sensors (default value 3), set to 1. When setting CWKONLS CDLSH must also be configured to prevent malfunction in circuit DTC's.
CWKONLS.1 = 0
CWKONLS.5 = 0
Change these to disable rear O2 lambda control:[59][60]

CLRHK (0x11A87) - Code word for Lambda - Bit 0 is Control post cat on/off. Set bit 2 and 0, clear bit 3 to disable; i.e. set from 72 (0x48/01001000b) to 5 (00000101b)[61]
CLRHK.0 = 1
CLRHK.2 = 1
CLRHK.3 = 0
CLRHK.6 = 0 (don't care)
CLRSHK - Wideband vehicles use CLRSHK. In these the default value is typically 16 (0x10/0001000b). Set bit 0 (and possibly set bit 2 and clear bit 3?) to disable (set to 5?)
CLRSHK.0 = 1
CLRSHK.2 = 1(?) unconfirmed.
CLRSHK.3 = 0(?) unconfirmed.
CLRKA (0x11A72) - set to 0[62]


* r32 eg.png (123.73 KB, 2131x911 - viewed 3 times.)
* 022906032EG.bin (1024 KB - downloaded 1 times.)
Logged
vwdubNam
Jr. Member
**

Karma: +1/-0
Offline Offline

Posts: 27


« Reply #1 on: July 31, 2018, 03:15:58 AM »

im not sure if this would be of help
keep the post updated please. i am very much interested in it
Logged
tonytony232
Jr. Member
**

Karma: +0/-4
Offline Offline

Posts: 26


« Reply #2 on: August 04, 2018, 01:08:52 AM »

hey all,

i can't find a damos or xdf for my ecu.. ive tried others to compare but to no avail.

I still have the rear 02's but no cats. i can either delete them or numb them to go through emissions but i cant figure out which bit is what for ither situation

anyone with a little insight as to whats what would be much appreciated

0x18194 is where control bits start.

i have the are where the control bits are but cant find the correct addresss for

You maybe able to numb ME7's sensitivity (note: untested) using: [55][56]

AHKATMN (0x18672) - leave alone
AHKATMX (0x18673) - set to max
AHKATS (0x18674) - set to max
AHKATSB (0x18675) - set to max

....or


 CDHSH - Post cat O2 heater diagnosis
CDHSHE - Post cat O2 heater amplifier diagnosis
CDLATV - Lambda sensor aging diagnosis (tv) in OBDII-Mode (inverse: EURO-Mode)
CDLASH - Lambda sensor aging diagnosis (SHK) in OBDII-Mode (inverse: EURO-Mode)
CDLSH - Post cat O2 sensor diagnosis
CDLSHV - Lambda sensor sensor interchange recognition (N/A for vehicles equipped with a single post cat sensor, IE 1.8t and certain vr6)
CWKONLS (0x181BB) - Vehicles with 4 installed sensors - change from 51 (0x33/00110011b) to 17 (0x11/00010001b)[58] Vehicles with 2 installed sensors (default value 3), set to 1. When setting CWKONLS CDLSH must also be configured to prevent malfunction in circuit DTC's.
CWKONLS.1 = 0
CWKONLS.5 = 0
Change these to disable rear O2 lambda control:[59][60]

CLRHK (0x11A87) - Code word for Lambda - Bit 0 is Control post cat on/off. Set bit 2 and 0, clear bit 3 to disable; i.e. set from 72 (0x48/01001000b) to 5 (00000101b)[61]
CLRHK.0 = 1
CLRHK.2 = 1
CLRHK.3 = 0
CLRHK.6 = 0 (don't care)
CLRSHK - Wideband vehicles use CLRSHK. In these the default value is typically 16 (0x10/0001000b). Set bit 0 (and possibly set bit 2 and clear bit 3?) to disable (set to 5?)
CLRSHK.0 = 1
CLRSHK.2 = 1(?) unconfirmed.
CLRSHK.3 = 0(?) unconfirmed.
CLRKA (0x11A72) - set to 0[62]


* r32 eg.png (123.73 KB, 2131x911 - viewed 3 times.)
* 022906032EG.bin (1024 KB - downloaded 1 times.)


So, u need to delete rear o2 sensors and that’s all?
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.016 seconds with 17 queries. (Pretty URLs adds 0s, 0q)